Related Manuals for Clarion CX201A
Summary of Contents for Clarion CX201A
- Page 1 Owner’s manual CX201A 2-DIN CD/USB/MP3/WMA RECEIVER UNIT PENERIMA CD/USB/MP3/WMA 2-DIN CD/USB/MP3/WMA 2-DIN...
- Page 2 CX201A...
-
Page 3: Table Of Contents
Thank you for purchasing this Clarion product. ∗ Please read this owner’s manual in its entirety before operating this equipment. Contents 1. FEATURES ............................3 2. PRECAUTIONS ..........................4 3. CONTROLS ............................. 5 Names of the Buttons and Their Main Functions ................5 4. -
Page 4: Precautions
EXPOSURE. THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL. CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. CX201A... -
Page 5: Controls
3. CONTROLS Names of the Buttons and Their Main Functions [CD SLOT] CX201A [DIRECT] [DIRECT] [SCN] [F-UP] [RPT] [F-DN] [RDM] RECEIVER] [SOURCE ] [BAND] [RESET ] [AUX] [ROTARY ] [SOUND] [USB] [DISP] [ISR ] [DIRECT] buttons [SOUND] button • Store radio stations in memory or recall it •... -
Page 6: Remote Control
• Recalls ISR radio station stored in memory. and hold the button (1 sec.) to perform folder • Press and hold the button (2 sec.) to store random play. current station in ISR memory (radio mode only). [DISP] button • Press to select the desired display. CX201A... -
Page 7: Inserting The Battery
• Do not subject battery to heat, or dispose of in compartment. fire or water. Do not attempt to disassemble the 4 Replace the cover and slide in until it clicks battery. into place. • Dispose of used batteries properly. Insertion guide CX201A... -
Page 8: Operations
Select the one you prefer. ∗ The volume level is from 0 (minimum) to 33 ∗ The factory default setting is “OFF”. (maximum). 2-1. Select “BEAT EQ” Switching the display Press the [DISP] button to select the desired display. CX201A... -
Page 9: Adjusting The Balance
You can set the low pass filter of subwoofer. 3-3. Turn the [ROTARY] knob to select the This adjustment can be performed only when setting. the “REAR/S-W” is set to “S-WOOFER”. BASS<G>:The factory default setting is “0”. 2-1. Select “LPF”. (Adjustment range: +7 to – CX201A... -
Page 10: Adjusting The High Pass Filter
“THROUGH” ↔ “60” ↔ “90” ↔ “120” ∗ The factory default setting is “THROUGH” (through). Note: • During SOUND adjustment mode, if no operation is performed for more than 10 seconds, this mode can be cancelled and return to previous mode. CX201A... -
Page 11: Radio Operations
● Recalling a station with ISR In any mode, press the [ISR] button to turn on the radio function and tune the selected radio station. “ISR” appears in the display. Press the [ISR] button again to return to the previous mode. CX201A... -
Page 12: Cd/Mp3/Wma Operations
2. Files without MP3/WMA data will not play. Instead, “- - : - -” will appear in the play time display. ∗ When MP3/WMA files are played, a little no sound part is caused between tunes. CX201A... -
Page 13: Displaying Cd Titles
1. Press the [x] button to move back to the Notes: beginning of the current track. • Never insert foreign objects into the CD SLOT. 2. Press the [x] button twice to move back to the beginning of the previous track. CX201A... -
Page 14: Random Play
MP3/WMA disc. 1. Press and hold the [SCN] button (1 sec.) to perform folder scan play. ● Repeat play This function allows you to play the current track repeatedly. 1. Press the [RPT] button to perform repeat play. CX201A... -
Page 15: Operations Common To Each Mode
Setting the anti-theft function To change adjustment setting (CATS) 1. Press and hold the [DISP] button (1 sec.) “CATS” is the acronym of “Clarion Anti-Theft to switch to the adjustment selection System”. When you set a PIN code (called as display. - Page 16 “OFF”. • If you have lost your Personal Code, please ● Anti-theft indicator contact Clarion customer service. 1. Enter your Personal Code currently set. The red Anti-theft indicator is a function for preventing theft. When the ACC is off, this 2.
- Page 17 ∗ The factory default setting is “MID”. 1. Press and hold the [DISP] button (1 sec.). 2. Select “AUX SENS”. 3. Turn the [ROTARY] knob to select “HIGH”, “MID” or “LOW”. Note: • When AUX mode is selected, AUX IN sensitivity can be set. CX201A...
-
Page 18: Accessories
• To prevent the accidental loss of data, always back up important data on your computer. • This unit does not support connections to a computer. In addition, connections made through a USB hub device are also not supported. CX201A... -
Page 19: Usb Memory Device
USB mode is selected, since it may result in loss or damage to data on the USB memory device. Always backup and save important data on your computer. 2. Remove the USB memory device from the USB connector. CX201A... -
Page 20: Ipod/Iphone Operations
Switch between these modes by pressing the • Some iPod models do not support this function. [BAND] button (1 sec.). Consult your nearest Clarion dealer or website to confirm which models do not support this Note: function. - Page 21 [ROTARY] knob fast, playback may not be performed. 2. Turn the [ROTARY] knob to select “Music” or “Video”. 3. Press the [ROTARY] knob. 4. Turn the [ROTARY] knob to switch between categories. The iPod menu categories alternate in the following order: CX201A...
- Page 22 [ROTARY] knob to select the desired subfolder. 3. When the track name display is showing, press the [ROTARY] knob. Playback will begin from the first track in the selected category, and the iPod menu mode will be canceled. CX201A...
-
Page 23: Troubleshooting
1. Turn down sound volume. Function can also be is operating. restored by turning the power off and on again. (Speaker volume is reduced automatically when the speaker protection circuit operates). 2. If the sound is muted again, consult our service department. CX201A... - Page 24 Can’t insert the The device has been inserted Try reversing the connection direction of the device device. improperly. (usually the brand name surface should be facing left). The connector is broken. Replace with a new device. CX201A...
-
Page 25: Error Displays
Do not support the HUB Do not use the HUB devices. devices. If an error display other than the ones described above appears, press the reset button. If the problem persists, turn off the power and consult your store of purchase. CX201A... -
Page 26: Specifications
Signal to Noise Ratio (1 kHz): 92 dB Dimensions / Source unit: Dynamic Range (1 kHz): 80 dB 178 (W) ✕ 100 (H) ✕ 155 (D) mm Harmonic Distortion: 0.03% Note: • Specifications and design are subject to change without notice for further improvement. CX201A... - Page 27 Clarion Co., Ltd. All Rights Reserved. Copyright © 2011: Clarion Co., Ltd. PE-3419K-B Printed in China / 2011/01 280-9006-00 Dicetak di Cina...