Transmitting A 1750 Hz Tone; Reverse Function; Automatic Simplex Checker (Asc); Tone Frequency Id - Kenwood TM-D710A (K type) Instruction Manual

TRANSMITTING A 1750 Hz TONE

Most repeaters in Europe require that a transceiver
transmit a 1750 Hz tone. On a E type model, simply
pressing Microphone [CALL] causes it to transmit a 1750
Hz tone. It is also possible to program [1750] on the front
panel as a PF key for transmitting a 1750 Hz tone.
Note: The transceiver continuously transmits a 1750 Hz tone until
you release Microphone [CALL] or PF key(1750).
Some repeaters in Europe must receive continuous
signals for a certain period of time, following a 1750 Hz
tone. This transceiver is also capable of remaining in the
transmit mode for 2 seconds after transmitting a 1750 Hz
tone.
1 Enter Menu mode and access Menu 402.
2 Set the tone to ON or OFF.
• When set to ON, the 1750 Hz tone will transmit. When
set to OFF, the tone will not be transmitted.
Note: While remaining in the transmit mode, the transceiver does not
continuously transmit a 1750 Hz tone.

REVERSE FUNCTION

After setting a separate receive and transmit frequency,
you can exchange these frequencies using the Reverse
function. This allows you to manually check the strength
of signals you receive directly from other stations, while
using a repeater. If the station's signal is strong, move to
a simplex frequency to continue the contact and free up
the repeater.
Press [REV] to turn the Reverse function ON or OFF.
• When the Reverse function is ON, the
the display.
Note:
◆ If the transmit frequency is outside the allowable transmit
frequency range when using Reverse, pressing [PTT] will cause
an error tone to sound and transmission will be inhibited.
◆ If the receive frequency is outside the receive frequency range
when using Reverse, an error tone will sound and Reverse will
not operate.
◆ The ARO (Automatic Repeater Offset) will not function when
Reverse is ON.
◆ You cannot switch Reverse ON or OFF while transmitting.

AUTOMATIC SIMPLEX CHECKER (ASC)

While using a repeater, ASC periodically monitors the
strength of signals you receive directly from the other
stations. If the station's signal is strong enough to allow
direct contact without a repeater, the
Press [REV] (1s) to turn the ASC ON.
• When the ASC is ON, the
icon will appear on
icon blinks.
icon will appear on the display.
• While direct contact is possible, without the use of a repeater,
the icon will begin blinking.
• To exit ASC, press [REV].
Note:
◆ Pressing [PTT] will cause the
◆ ASC does not function if you are using simplex operation.
◆ ASC does not function while scanning.
◆ Activating ASC while using Reverse will switch the Reverse
function OFF.
◆ If you recall a Memory channel or the Call channel, and those
channels are set up with the Reverse function switched ON, the
ASC will switch OFF.
◆ You cannot use ASC when the built-in TNC is turned ON.
◆ ASC causes received signals to be momentarily intermitted every
3 seconds.

TONE FREQUENCY ID

This function scans through all tone frequencies to identify
the incoming tone frequency on a received signal. You
can use this function to find which tone frequency is
required by your local repeater.
1 Press [TONE] to switch the Tone function ON.
• The icon appears on the display.
2 Press [F], [T.SEL] (1s) to run the Tone Frequency ID
scan.
• The icon blinks and SCAN appears on the display.
• To reverse the scan direction, turn the Tuning control
clockwise (upward scan) or counterclockwise (downward
scan).
• To quit the function, press [ESC].
• When the tone frequency is identified, the identified
frequency appears on the display and blinks. Press any
key other than the Tuning control while the identified
frequency is blinking, to resume scanning.
3 Press the Tuning control to program the identified
frequency in place of the currently set tone frequency.
• The Tone function will remain ON. You can press
[TONE] to switch the Tone function OFF.
• Press [ESC] if you do not want to program the identified
frequency.
REPEATER-3
icon to stop blinking.