Page 3: Table Of Contents
Table of Contents Introductory Information ....... 1 Safety Restraints ..........9 Starting Your Probe ........37 Warning Lights and Gauges ....... 51 Instrument Panel Controls ......63 Steering Column Controls ......77 Features ............95 Electronic Sound Systems ......121 Driving Your Probe ........
Page 4: Introductory Information
Introductory Information Ford’s Commitment to You At Ford Motor Company, excellence is the continuous commitment to achieve the best result possible. It is dedication to learning what you want, determination to develop the right concept, and execution of that concept with care, precision, and attention to detail.
Page 5 This guide describes equipment and gives specifications for equipment that was in effect when this guide was approved for printing. Ford may discontinue models or change specifications or design without any notice and without incurring obligation.
Page 6 Canadian Owners — French Version French Owner Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3.
Page 7 If you lose your Warranty Information Booklet, you can get a new one free of charge. Contact any Ford or Lincoln-Mercury dealer, or refer to the addresses and phone numbers on the first page of this owner guide.
Page 8 Your Ford dealer has information about the availability of many items of equipment which may be ordered for your vehicle.
Page 9 Use only the type of engine oil that Ford recommends. See Engine oil recommendations in the Index. Do not use special “break-in” oils. Cleaning the Outside of Your Vehicle Washing and Polishing Your Vehicle Wash the outside of your vehicle, including the underside, with a mild detergent.
Page 10 Cleaning Chrome and Aluminum Parts Wash chrome and aluminum parts with a mild detergent. Do not use steel wool, abrasive cleaners, fuel or strong detergents. Cleaning Plastic Parts Some of your vehicle’s exterior trim parts are plastic. Clean with a tar and road oil remover if necessary.
Page 11: Safety Restraints
Safety Restraints Important Safety Belt Information The use of safety belts helps to restrain you and your passengers in case of a collision. In most states and in Canada the law requires their use. Safety belts provide best restraint when: the seatback is upright the occupant is sitting upright (not slouched) the lap belt is snug and low on the hips...
Page 12 Failure to follow these precautions could increase the risk and/or severity of injury in a collision. RWARNING Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Safety belt assemblies...
Page 13: Combination Lap And Shoulder Belts
Combination Lap and Shoulder Belts While your vehicle is in motion, the combination lap and shoulder belt adjusts to your movement. However, if you brake hard, turn hard, or if your vehicle receives an impact of 5 mph (8 km/h) or more, the lap and shoulder belt locks and helps reduce your forward movement.
Page 14 Unfastening the combination lap and shoulder belt — front and rear seating positions While the belt retracts, guide the tongue to its original position to prevent it from striking you or the vehicle. Lap/Shoulder Belt Retractors (Dual Locking Modes) Your vehicle is equipped with a dual locking mode retractor on the shoulder belt portion of the combination lap/shoulder safety belt for all passengers.
Page 15 Automatic locking mode In this operating mode, the shoulder belt retractor will be automatically locked and will remain locked when the combination lap/shoulder safety belt is buckled, and does not allow the occupant freedom of movement. This mode provides the following: A tight lap/shoulder belt on the occupant.
Page 16: Safety Belt Maintenance
(slide bar) (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after any collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision...
Page 17 Cleaning the Safety Belts Clean the safety belts with any mild soap solution that is recommended for cleaning upholstery or carpets. Do not bleach or dye the belt webbing because this may weaken it. Air Bag Supplemental Restraint System (SRS) The driver and right front passenger air bags are Supplemental Restraint Systems (SRS), provided at these seating positions in addition to the...
Page 18 There are four very important reasons to use safety belts even with an air bag system. Use your safety belts to: help keep you in the proper position (away from the air bag) when it inflates reduce the risk of harm in rollover, side or rear impact collisions, because an air bag is not designed to inflate in such situations reduce the risk of harm in frontal collisions...
Page 19 In rear-facing infant seats, the infant’s head is closer to the air bag. The force of the rapidly inflating air bag could push the top of the rear-facing seat against the vehicle seatback or center armrests (if so equipped), or center console (if so equipped).
Page 20 THE FORCE OF THE RAPIDLY INFLATING PASSENGER AIR BAG COULD PUSH THE TOP OF THE REAR-FACING SEAT AGAINST THE VEHICLE SEATBACK, ARMRESTS OR CONSOLE. REAR-FACING INFANT SEATS MUST ALWAYS BE SECURED IN THE REAR SEAT. RWARNING Do not place objects or mount equipment on or near the air bag cover on the steering wheel or in front seat areas that may come in contact with a deploying air...
Page 21 The location of the air bag and warning labels If a collision occurs, the sensors sense the severity of the impact and activate the air bags if necessary. The air bag system is designed to deploy in frontal and front-angled collisions more severe than hitting a parked vehicle (of similar size and weight) head-on at about 28 mph (45 km/h).
Page 22 When the sensors activate the system, the air bags inflate rapidly, filling with non-toxic nitrogen gas in a fraction of a second. Immediately after inflation, the air bags deflate by releasing the nitrogen gas through vent holes. The whole process takes place in a matter of seconds.
Page 23 Inflated passenger-side air bag RWARNING If the air bag is inflated, THE AIR BAG WILL NOT FUNCTION AGAIN AND MUST BE REPLACED IMMEDIATELY. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 24 If any of these things happen, have the air bag system serviced at your Ford or Lincoln-Mercury dealer immediately. Unless serviced, the air bag supplemental restraint system may not function properly in the event of a collision.
Page 25: Safety Restraints For Children
Safety Restraints for Children In the U.S. and Canada, you are required by law to use safety restraints for children. If small children ride in your vehicle — this generally includes children who are four years old or younger and who weigh 40 pounds (18 kg) or less —...
Page 26 When possible, put children in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating positions. RWARNING Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle.
Page 27 Always follow the safety seat manufacturer’s instructions when installing and using the safety seat. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 28 RWARNING When using forward-facing child seats move the passenger seat as far back from the instrument panel as possible. NEVER SECURE REAR-FACING INFANT SEATS IN THE FRONT SEAT. THE FORCE OF THE RAPIDLY INFLATING PASSENGER AIR BAG COULD PUSH THE TOP OF THE REAR-FACING SEAT AGAINST THE VEHICLE SEATBACK, ARMRESTS OR CONSOLE.
Page 29 Installing Child Safety Seats Your vehicle is equipped with a dual locking mode retractor on the shoulder belt portoin of the front passenger seat and both rear seats. The automatic locking mode must be used when installing a child seat or infant carrier in the front passenger seat or rear seats.
Page 30 Grasping lap and shoulder belt together 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted.
Page 31 Routing safety belt through child seat or infant carrier Buckling the belt...
Page 32 4. Grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. At this time, the retractor is in the automatic locking mode (child seat restraint mode). Setting the retractor to automatic locking mode 5.
Page 33 Removing slack from belt 6. Before placing the child in the child seat or infant carrier, forcibly tilt the seat from side to side, and tug it forward to make sure that the seat is securely held in place.
Page 34 Checking that the seat is secure 7. Double check that the retractor is in the automatic locking mode. Try to pull more belt out of the retractor. If you cannot, the belt is in the automatic locking mode.
Page 35 Checking the retractor 8. Check to make sure that the child seat or infant carrier is properly secured prior to each use. If the belt is not locked, repeat steps 4 through 7. NOTE: To remove the retractor from automatic lock mode, allow seat belt retract fully to its stowed position and the retractor will automatically switch back to the...
Page 36 RWARNING When using any infant or child restraint system, it is important that you follow the instructions and warnings provided by the manufacturer concerning its installation and use. Failure to follow each of the restraint manufacturer’s instructions could increase the risk or severity of an injury in the event of a collision or sudden stop.
Page 37 Tether Anchorage Hardware Tether anchor hardware kits can be obtained at no charge from any Ford or Lincoln-Mercury dealer. Be sure to follow the child safety seat manufacturer’s instructions.
Page 38 3. Install the hardware for anchoring the tether following the instructions in the tether anchorage hardware kit. 4. Re-install luggage compartment cover. Installing the anchor bracket...
Page 39: Starting Your Probe
Starting Your Probe Ignition Understanding the Positions of the Ignition Ignition lock cylinder LOCK locks the steering wheel. It also locks the gearshift lever in P (Park) (automatic transaxle). LOCK is the only position that allows you to remove the key. The LOCK feature helps to protect your vehicle from theft.
Page 40 ON allows you to test your vehicle’s warning lights (except the brake system warning light) to make sure they work before you start the engine. The key returns to the ON position once the engine is started and remains in this position while the engine runs.
Page 41 Automatic console-mounted gearshift lever NOTE: When the ignition key is in the ACC or LOCK position, the transaxle cannot be shifted from the P (Park) position. If the brake pedal is repeatedly depressed and released when the ignition is in the ON position and the selector lever is in the P (Park) position, a chattering near the gearshift lever may be heard.
Page 42 Please refer to the chapter titled Servicing Your Probe in this Owner Guide for instructions on checking and replacing fuses.
Page 43 Removing the Key From the Ignition 1. Put the gearshift selector lever in P (Park) (automatic transaxle) or 1 (First) (manual transaxle). 2. Set the parking brake fully. 3. For a manual transaxle: Push in on the lock cylinder and turn the key from ACC to LOCK.
Page 44: Starting Your Vehicle
Fuel-Injected Engines When starting a fuel-injected engine, the most important thing to remember is to avoid pressing down on the accelerator before or during starting. Only use the accelerator when you have problems getting your vehicle started. See Starting Your Engine in this chapter for details about when to use the accelerator while you start your vehicle.
Page 45: Warning Lights And Gauges
Testing the Warning Lights Before you start your vehicle, you should test the warning lights on the instrument panel to make sure that they work. Refer to the Warning Lights and Gauges chapter. Starting Your Engine To start your engine: 1.
Page 46 For a warm engine: Do not hold the key in the START position for more than five (5) seconds at a time. If the engine does not start within five (5) seconds on the first try, turn the key to the OFF position.
Page 47 To turn the heater on, simply plug it into a grounded 110-volt outlet. Ford recommends that you use a 110-volt circuit that is protected by a ground fault circuit interrupter.
Page 48 RWARNING To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. For best results, plug the heater in at least three hours before you start your vehicle. Using the heater for longer than three hours will not damage the engine, so you can plug it in at night to start your vehicle the following morning.
Page 49 The location of the fuel pump shut-off switch RWARNING If you see or smell fuel, do not reset the switch or try to start your vehicle. Have all the passengers get out of the vehicle and call the local fire department or a towing service.
Page 50 If your engine cranks but does not start after a collision or substantial jolt: 1. Turn the key in the ignition to the LOCK position. 2. Check under the vehicle for leaking fuel. 3. If you do not see or smell fuel, push the red reset button on the fuel pump shut-off switch down.
Page 51 RWARNING If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Have the exhaust and body ventilation systems checked whenever: your vehicle is raised for service the sound of the exhaust system changes your vehicle has been damaged in a collision Improve your ventilation by keeping all air inlet vents clear of snow, leaves, and other debris.
Page 52: Warning Lights And Gauges
We call this grouping a cluster. To clean the lenses on your instrument panel, use Ford Glass Cleaner and a soft cloth. Never use paper towels or abrasive cleaners; they can scratch the lenses.
Page 55 The mechanical cluster on the Probe GT model is similar to the one shown. The two exceptions are: the speedometer on the GT model shows 140 mph (225 km/h) and it has a 7,000 rpm red-line tachometer. GT model speedometer and tachometer The following warning lights and gauges are on the cluster.
Page 56 Air bag readiness light RWARNING If any of these things happen, even intermittently, have the air bag system serviced at your Ford or Lincoln-Mercury dealer immediately. Brake System Warning Light Your vehicle has a divided brake system. If one part isn’t working, the other part can still work and stop you.
Page 57 This light should come on as you start the vehicle. If it doesn’t come on then, have it fixed so it will be ready to warn you if there’s a problem. Brake system and parking brake light This light comes on briefly when you turn the ignition key to START.
Page 58 Anti-Lock Brake System Warning Light When the ignition switch is turned to the ON position, the anti-lock brake system warning light will come on. When the engine is started, the anti-lock brake system control unit will determine if all components of the system are operating correctly.
Page 59 The Low Fuel Light This light comes on when fuel level in your tank has reached approximately 2-3 gallons (7-10 liters). Low fuel light High Beam Light This light comes on when the headlamps are turned to high beam or when you flash the lights.
Page 60 This light comes on briefly when you turn the ignition to the ON position, but should turn off when the engine starts. If the light does not come on when you turn the ignition to the ON position or if it comes on and stays on when you are driving, have your vehicle serviced as soon as possible.
Page 61 Gauges Fuel Gauge The fuel gauge displays approximately how much fuel you have in the fuel tank. The ignition must be turned off while putting fuel in the tank in order to get a correct fuel gauge reading after the ignition is turned on. The fuel gauge indicator may vary slightly while the vehicle is in motion.
Page 62 3. Check the oil level when the vehicle is on level ground. 4. Add only as much oil as the engine needs before you drive the vehicle again. Do not overfill the oil reservoir. For more information, see Adding engine oil in the Index.
Page 63 For instructions on checking and adding coolant to your engine, see Engine coolant in the Index. If you do not follow these instructions, you or others could be injured. 5. Add as much coolant as your engine needs. If the engine continues to overheat, have the coolant system serviced.
Page 64: Instrument Panel Controls
Instrument Panel Controls The main controls for the climate control system, clock, and radio are on the instrument panel.
Page 66 NOTE: Any cleaner or polish that increases the gloss (shine) of the upper part of the instrument panel should be avoided. The dull finish in this area is to help protect the driver from undesirable windshield reflection. The Climate Control System Heating Only System (Without Air Conditioning) Function selection...
Page 67 The FLOOR position directs air out the floor outlets and the side window defoggers. Ventilate your vehicle with outside air by choosing the VENT position. Temperature control The air temperature can be adjusted by moving the marker on the temperature control to the red area for warm air, or to the blue area for unheated air.
Page 68 Defrosting the Windshield and Side Windows 1. Turn the function selector control to the defrost position. When V is selected, air is directed to the windshield and side windows. 2. Turn the temperature control to the desired temperature. 3. Set the fan at the desired speed. Heating and Defrosting at the Same Time 1.
Page 69 Tips for Controlling the Temperature in Your Vehicle To vary the temperature inside your vehicle, move the temperature selector toward the red area for warmer air and toward the blue area for cooler air. If you drive with the fan off and the windows closed, the windows may fog up.
Page 70 Sometimes you may notice slight engine surging if you have the air conditioner on. This is normal, as the system is designed to cycle the compressor on and off to maintain desired cooling. The reduced compressor operation should benefit fuel economy. On some vehicles with air conditioning, wide-open throttle acceleration will temporarily cut off the air conditioning.
Page 71 Because MAX A/C uses recirculated air, MAX is usually more efficient than NORM A/C. You can switch to outside air (NORM A/C) at any time, especially after the vehicle has cooled down. You will notice a slight odor when using the MAX A/C position.
Page 72 Engine Idle Speed Control System Genuine Ford air conditioning (either factory-installed or dealer-installed) has an engine idle speed control system that compensates for engine speed loss that may occur when the air conditioning compressor is running. This idle speed control holds the engine idle essentially constant, regardless of whether the air conditioning system is on or off.
Page 73: Interior Lights
To defrost the rear window: 1. Clear any snow from the rear window. 2. Get in your vehicle and start the engine. 3. Press the rear defrost button. The indicator light turns on. The defroster turns off automatically after 15 to 25 minutes.
Page 74 The dimmer control thumbwheel is located to the left of the steering wheel on the instrument panel. Dome Lamp The dome lamp illuminates whenever one of the front doors is opened and turns off automatically when the doors are closed. You may turn the dome lamp on and off while the doors are closed by using the ON/OFF switch located on the interior/map lamp control panel.
Page 75 Push the buttons again to turn the map lamps off. Cleaning the Interior Lamps Your interior dome lamps and map lamps are plastic and should be cleaned with a mild detergent diluted in water. Rinse them with clear water. Fog Lamps (If equipped) The fog lamps only operate when the headlamps are on low beam.
Page 76 Fog lamp button Radio For information about the radio in your vehicle, refer to the Ford Electronic Sound Systems Operating Guide in this Owner Guide. Clock Controls on Electronic Radios The electronic radios have a built-in clock. For complete operating instructions, refer to the Ford Electronic Sound Systems Operating Guide in this owner guide.
Page 77: Steering Column Controls
Steering Column Controls The controls on the steering column and wheel are designed to give you easy access to the controls while you are driving. The Turn Signal Lever You can use the turn signal lever on the left side of the steering column to: operate the headlamps and parking lamps operate the turn signals and cornering lamps...
Page 78 Headlamp control Daytime Running Light System (Canadian vehicles only) In Canada, certain regulations require vehicles to be driven with lights illuminated during daytime operation. It is for that reason that the daytime running lights are automatically illuminated when the ignition switch is turned to the ON position.
Page 79 Before using the manual retractors to raise your headlamps, the RETRA fuse must be removed. Open the main fuse panel. Refer to the underhood fuse panel in Servicing Your Probe later in this owner guide. Pull the RETRA (20A) fuse straight out.
Page 80 Manual headlamp retractors located behind the headlamps High Beams and Flashing the Lamps To turn on the high beams, turn the headlamp control knob to the headlamp ON position and push the turn signal lever away from you until it latches. When the high beams are ON, the high beam indicator light on the instrument panel comes on.
Page 81 Flashing the Lights To flash the headlamps, pull the lever toward you for a moment and then release it. The headlamps will flash whether the headlamp knob is in the on or off position. Highbeam and flash-to-pass operation If the headlamps are retracted when you pull the lever toward you, they will pop up and flash.
Page 82 If the flashers run for longer than 2 hours while your engine is not running, or if your battery is not fully charged, your battery could be drained. Hazard warning flasher switch...
Page 83 Turn Signals Move the lever up to signal a right turn. Move it down to signal a left turn. The corresponding indicator light in the instrument cluster will flash. If the turn signal stays on after you turn, move the lever back to the center (OFF) position. For lane changes, move the lever far enough to signal but not to latch.
Page 84: Windshield Wipers And Washer
Windshield Wipers and Washer To operate the windshield wipers and washers, make sure your ignition key is turned to the ON position. The windshield wipers have two speeds. To operate the wipers, pull down the lever on the right side of your steering column. The first position is LO (Low) and the second position is HI (High).
Page 85 Interval Wipers (If equipped) In addition to two speed wipers, your vehicle may have wipers that you can set to operate at varying intervals. For example, you can set the interval so they wipe less often when it drizzles and more often in heavier rain. Variable interval wiper control To set the interval wipers, pull the lever down to the first position.
Page 86 If the washer does not work, check the washer fluid level visually and fill if needed. See Servicing Your Probe later in this owner guide. If there is fluid in the reservoir, and your washer doesn’t work, consult your Ford or Lincoln-Mercury dealer.
Page 87 Horn To sound the horn, push the horn button on either side of the steering wheel. Check the horn regularly to be sure it operates properly. Using the horn...
Page 88: Tilt Steering Column
Tilt Steering Column (If equipped) RWARNING Never adjust the steering column/wheel when the vehicle is moving. You could lose control of the vehicle and injure someone. To change the position of the steering column/wheel, pull the release lever on the column toward you.
Page 89 Speed Control (If equipped) If your vehicle has speed control, you can automatically maintain a constant speed at or above 30 mph (50 km/h). Use of radio transmitting equipment that is not Federal Communications Commission (FCC) or in Canada the Canadian Radio and Telecommunications Commission (CRTC) approved may cause the speed control to malfunction.
Page 90 3. Press SET ACC and release it immediately to set your speed. If you keep this button depressed, your speed will continue to increase. 4. Take your foot off the accelerator pedal. Your vehicle will maintain the speed you set. If you drive up or down a steep hill, your vehicle may momentarily slow down or speed up, even though the speed control is on.
Page 91 RWARNING Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. Accelerating With the Speed Control Operating If you want to speed up momentarily or regain preset speed on hills when the speed control is operating, simply accelerate using the accelerator pedal.
Page 92 NOTE: If your vehicle has an automatic overdrive transaxle, you may want to drive with the Overdrive off when driving in hilly terrain or at high altitudes. You may turn the Overdrive off and use Drive by pressing the Overdrive off (O/D OFF) button. This will improve speed control performance.
Page 93 To Cancel Speed Control You can cancel the speed control while you are driving. Press the brake pedal or clutch pedal (manual transaxle) slightly. The speed control is cancelled, but you can reset it by pressing SET ACC or RSM. To Turn Off the Speed Control System Press the OFF switch.
Page 94 Tap Up and Tap Down (2.0L vehicles with automatic transaxle only) Tap Up and Tap Down is a new feature which, like SET ACC and CST, can be used to either increase or decrease the set speed. Speed changes are made in 1 mph (1.6 km/h) increments.
Page 95: Features
Features Your vehicle has a variety of features designed for your comfort, convenience and safety. Read this chapter to find out about standard and optional features. Doors The outside of the door The inside of the door If you close the door with the lock button depressed, the door will remain locked.
Page 96 Power Door Locks (If equipped) If your vehicle has power door locks, the controls to lock the doors are below the inside door handles on each door. When you close the doors after you set the door locks, the doors remain locked.
Page 97 Power locks on the driver’s door Remote Keyless Entry System (If equipped) Your vehicle may be equipped with a remote keyless entry system. This option will allow you to open your vehicle using a remote transmitter from distances of up to 33 feet (10 meters) away. The remote feature will operate only when the ignition is in the OFF position.
Page 98 You can lock all your vehicle doors by pressing the LOCK button. If you press the LOCK button a second time within five (5) seconds, the horn will sound briefly to verify that the doors have been locked. When the PANIC button is pressed, the horn will sound and the hazard warning lamps will flash.
Page 99 Replacement batteries can be purchased at most pharmacies, watch stores or at your Ford or Lincoln-Mercury dealer. NOTE: The operating range of the remote entry system can also be affected by...
Page 100 The transmitter can be snapped apart to replace the batteries by twisting a thin coin between the two halves of the transmitter. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. Carefully remove the old batteries. When installing the new batteries, be sure to place the positive (+) side down as marked.
Page 101 Windows Operating the Windows Manually The side windows on your vehicle can be raised or lowered manually by turning the hand crank located on each door. NOTE: If you notice buffeting or pulsation (wind shock) with either side window open, you should open the opposite window slightly to reduce the condition.
Page 102 Master window control on the driver’s door Moon Roof (If equipped) The control switch for the sliding moon roof is on the interior/map lamp control panel located above the windshield and between the sun visors. The ignition must be in the ON position for the moon roof to be operational.
Page 103 Sliding moon roof control switch Press the switch until the moon roof is opened to the desired position. When you release the switch, the moon roof will stop sliding open. To close the moon roof, press the other side of the switch and hold it until the roof is closed to the desired position.
Page 104 RWARNING To reduce the risk of serious injury in a collision, children should always ride with the seatback upright. Head Restraints Head restraints help protect your head and neck in a collision. The head restraints on your vehicle are not adjustable. Manual Seat Adjustments You can move the front seats forward or backward or tilt the back of the seat forward or...
Page 105 To move the seat forward or backward: Manual seat controls for front seats...
Page 106 To recline the seatback:...
Page 107 To gain access to the rear seat on the driver’s or passenger’s side: Seatback release lever for rear seat access The seatback will return to its set reclined position when pushed back. RWARNING A seatback which is folded forward even a small degree may not lock properly in the event of a sudden stop or collision.
Page 108 To inflate the driver’s seatback lumbar support (if equipped) for lower back support, or to inflate the driver’s seatback side bolster supports (if equipped):...
Page 109 Six-Way Power Seat Adjustment (if equipped) The six-way power seat control lever is located on the outermost side of the driver’s seat.
Page 110 Your seat cushion power adjust lever is operated by a motor. To avoid damage to the motor, you should avoid operating this feature for an extended period of time. You should also avoid using the six-way power adjust lever continuously with the engine stopped. This could run down the battery.
Page 111 To lower the rear seatback: To raise the seatback, lift the seatback rearward until it latches. Make sure the seatback is locked in position by pushing it forward and backward. RWARNING Securely latch the seatback in the upright position to prevent the seatback or objects from being thrown forward during a sudden stop or collision.
Page 112 RWARNING Do not remove the floor carpet in your vehicle. Emission controls cause high exhaust temperatures under the floor. NOTE: When returning the folding seats to the upright position, remember to return rear shoulder belts to their proper position. NOTE: Your vehicle has stowage hooks on the rear, lower, side trim panel on which to hook the safety belts when not in use.
Page 113 Mirrors RWARNING The side view mirror on the right makes objects appear smaller and farther away than they actually are. Dual-Electric Remote Control Mirrors (If equipped) Dual-electric remote control mirrors are collapsible. The mirror heads can be folded rearward to prevent damage when using an automatic car wash.
Page 114 Dual-electric side mirror control switches Console A fully-equipped console on your vehicle will include the following items: ashtray and lighter parking brake lever cupholder or storage compartment with cupholder...
Page 115: Storage Compartments
Storage Compartments Your vehicle may have several small storage compartments: a glove compartment that locks and unlocks using the ignition key two map pockets on the door panels (if equipped) storage compartment below the climate controls a storage bin in the center console RWARNING Do not put objects on the ledge between the back seat and the rear window, as...
Page 116 Using the cupholders Hatchback Opening and Closing the Hatchback To open the hatchback from the outside: 1. Put the key into the lock located on the right side, in the tail lamp just above the bumper. 2. Turn the key to the right to unlock. 3.
Page 117 To prevent premature wear or damage to the hatchback lift cylinders and attaching hardware, the hatchback must be fully closed before you drive your vehicle. RWARNING If you drive with the hatchback lid open, you will draw dangerous exhaust fumes into your vehicle.
Page 118 Using the Luggage Compartment Cover This cover lets you conceal cargo in the luggage compartment. The cover will lift automatically when the hatchback lid is opened. RWARNING Do not place objects on the luggage compartment cover, as they can become dangerous projectiles and injure someone.
Page 119 The luggage compartment and cover RWARNING The cover may cause injury in a sudden stop or accident if it is left lying loose in the vehicle or if it is not securely installed. Therefore, the cover should either be securely installed or removed from the vehicle.
Page 120 To install the luggage compartment cover: 1. Raise the hatchback to the fully open position. 2. From outside the vehicle, position the cover in its sockets. 3. Attach the lift cords to the hatchback lid. 4. Connect the two front luggage compartment cover lift cords to the lower trunk side trim.
Page 122 Compact Disc Radio The Compact Disc Radio combines the Electronic Stereo Radio with the Ford Compact Disc Player. Using the Controls on Your New Radio/CD Player Most of the features of this unit work for both radio and CD operation, depending on which mode the unit is in.
Page 123 How to tune radio stations There are four ways for you to tune in a particular station. You can manually locate the station using the “SCAN/TUNE” button, “SEEK” the station, “SCAN” to the station or select the station by using the memory buttons, which you can set to any desired frequency.
Page 124 Using the “SCAN/TUNE” button to scan radio stations Pressing the “SCAN/TUNE” button once enters the scan mode (display will indicate “SCN”). Pushing the top a half of the “SEEK” button will begin the scan mode up the frequency band, stopping on each listenable station for approximately five seconds.
Page 125 Using the Automatic Memory Load feature You can activate the Auto Memory Load feature by pressing and holding the “AUTO PRESET” button for approximately three seconds. Auto Memory Load sets all memory buttons in AM, FM1 and FM2 sequentially by seeking out the first five strong stations for the respective band and storing them in memory buttons 1-5.
Page 126 After all stations have been filled, the radio will begin playing the station stored on memory button 1. To deactivate the Auto Memory Store mode and return to the manually-set memory button stations (or those stations set using Auto Memory Load), simply push the “AUTO PRESET”...
Page 127 Adjusting speaker fader Fade control allows you to adjust the sound distribution between the front and rear speakers. Push the “AUDIO” button repeatedly until the display reads “FADE.” Push the “+” side of the “VOL” button to shift the sound to the front speakers, and push the “-”...
Page 128 Using the Controls on Your New Compact Disc Player Your new Ford Compact Disc Player is capable of playing 12 cm or 8 cm discs, without an adapter! The Player operates when the power is on and a disc is inserted (label side up). Handle the disc by its edge only.
Page 129 NOTE: Once a disc is inserted, the disc opening is secured to prevent the accidental insertion of a second disc. NOTE: The CD player has heat protection circuitry to protect the laser diode. If the temperature of the player reaches 167˚F (75˚C), the heat detection circuit will shut off the player and “TOO HOT”...
Page 130 Pressing and holding the bottom ( b ) or top ( a ) half of the “SEEK” button will scroll backward and forward respectively through the tracks. How to fast forward or reverse your CD player To quickly search for a particular point in a selection, press the “FF”...
Page 131 How To Take Care of and Clean Your CD Player and Discs To ensure the continued performance of your Ford Compact Disc Player, carefully read the following precautions: Always handle the disc by its edge. Never touch the playing surface.
Page 132 CD format. Because of this, a new disc that is free of dust and scratches could be defective and may not play on your Ford Compact Disc Player.
Page 133 If play does not begin after the CD button is pushed: The radio is not on. The unit is in the stop mode. Moisture may have condensed on the lenses within the unit. If this occurs, remove the disk and wait approximately an hour until the moisture evaporates.
Page 136 Using the Controls on Your New Radio How to turn the radio on and adjust the volume Press the “POWER” button to turn the radio on. Press it again to turn it off. Press the right (+) side of the “VOLUME” button to increase the volume.
Page 137 How to tune radio stations (Stereo Cassette Radio) There are four ways for you to tune in to a particular station. You can manually locate the station by using Automatic Music Search (“AMS”), “SEEK” the station, “SCAN” to the station or select the station by using the memory buttons, which you can set to any desired frequency.
Page 138 Using the “SEEK” function This feature on your radio allows you to automatically select listenable stations up or down the frequency band. Press the right ( a ) side of the “SEEK” button to select the next listenable station up the frequency band. Press the left ( b ) side of the button to select the next listenable station down the frequency band.
Page 139 NOTE: If the vehicle’s battery is disconnected, the clock and station memory preset buttons (if programmed in auto mode) will need to be reset. Adjusting the tone balance and speaker output of your radio Increasing or decreasing bass response Push the “AUDIO” button repeatedly until the display reads “BASS.”...
Page 140 Adjusting speaker fader Fade control allows you to adjust the sound distribution between the front and rear speakers. Push the “AUDIO” button repeatedly until the display reads “FADE.” Push the right (+) side of the “VOLUME” button to shift the sound to the front speakers, and push the left (-) side to shift the sound to the rear speakers.
Page 141 Using the Automatic Music Search (“AMS”) function with cassette tape player Press and hold the “AMS” button (“AMS” will appear in the display). Then, push the left ( h ) button to rewind to the beginning of the current selection or press the right ( g ) button to fast forward to the beginning of the next selection.
Page 142 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford Cassette Cleaning Cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 143 Clock Operation How to view the clock mode Press the “CLOCK” button to alternate the frequency and time in the display. In the clock mode, pressing any radio function will automatically display the radio frequency for approximatedly ten seconds before changing back to the clock mode.
Page 144 NOTE: Always make sure your antenna (whether you have a power antenna or a manually adjustable antenna) is fully extended to the maximum length for proper reception. If your antenna is not fully extended, you may experience signal loss while traveling in fringe reception areas.
Page 145 Several sources of static are normal conditions on AM frequencies. These can be caused by power lines, electric fences, traffic lights and thunderstorms. Another reception phenomenon is Strong Signal Capture and Overload. This can occur when listening to a weak station and when passing another broadcast tower.
Page 146 Ask your dealer for a copy of this limited warranty. Service At Ford Electronics, we stand behind our audio systems with a comprehensive service and repair program. If anything should go wrong with your Ford audio system, return to your dealer for service.
Page 147: Driving Your Probe
Driving Your Probe Procedures for driving your vehicle will vary depending on which type of transaxle your vehicle has. You may be familiar with the term “transmission.” We use transaxle because it is a more accurate term for vehicles that have front-wheel drive.
Page 148 Automatic shift lever Your automatic transaxle vehicle has a console-mounted shift selector lever. You must step on the brake pedal, start the engine, and then push in the thumb button to move the shift selector lever to the position you choose. RWARNING Hold the brake pedal down while you move the gearshift lever from position to...
Page 149 NOTE: If the shift selector lever will not move with the key on and the brake pedal depressed refer to Shift lock system in the Index. Once the gearshift is secure in the desired position, release the brake pedal and use the accelerator as necessary.
Page 150 Cancelling Overdrive The Overdrive Off (O/D OFF) button is located on the gearshift. The Overdrive Off (O/D OFF) light is located in the instrument cluster. The O/D OFF light is not illuminated during normal vehicle operation. This allows the transaxle to upshift and downshift from 1st through 4th gears.
Page 151 When to use Drive (D with Overdrive OFF) In Drive (Overdrive OFF), your vehicle automatically upshifts or downshifts from 1st through 4th gears as the vehicle speeds up or slows down. It also downshifts when you need extra acceleration to pass or when driving up a hill.
Page 152 Reverse In the Reverse (R) position, the vehicle moves only backward. Your vehicle must be stopped before shifting into Reverse (R). Neutral In Neutral (N), the wheels of the transaxle are not locked. Your vehicle will roll freely, even on the slightest incline, unless the parking brake or brakes are on.
Page 153: Driving With A Manual Transaxle
RWARNING Hold the brake pedal down while you move the gearshift lever from position to position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. Driving with a Manual Transaxle Using the Clutch After the engine starts, allow it to idle for a few seconds.
Page 154 Shifting the Gears The gearshift for a manual transaxle is mounted on the floor. The gearshift can be in one of seven possible positions, as shown. Shift pattern Always push the clutch pedal all the way in when you shift. You should upshift according to the speeds given in the chart later in this chapter.
Page 155 Backing up To shift into R (Reverse): 1. Bring your vehicle to a complete stop. 2. Push the clutch pedal in all the way to the floor and hold it. If you do not hold the clutch pedal in all the way, you may hear a grinding noise when you shift.
Page 156 Upshifting For normal acceleration, you should upshift at the following speeds: For cruising, you should upshift at the following speeds. Downshifting When you slow down or climb a steep hill, always downshift before the engine starts to lose power. Downshifting reduces the chance of stalling and gives your vehicle better acceleration to increase speed again.
Page 157: Steering Your Vehicle
Parking To park your vehicle, shift into 1 (First), set the parking brake fully, and turn off the ignition. RWARNING Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully.
Page 158 If your vehicle does not have anti-lock brakes, apply the brake pedal gradually. Use the “squeeze” technique — push on the brake pedal with a steadily increasing force. This allows the wheels to continue to roll while you are slowing down, which lets you steer properly.
Page 159 This is a normal part of the self-check feature. If a malfunction is found during this check the ABS light will come on. Ford Motor Company has not found any detrimental effects of popular mobile road transmitting equipment installed on vehicles...
Page 160 ON position, or during a sudden stop, have your mobile radio dealer inspect the radio installation. Proper radio installation procedures to be followed are published by the radio manufacturer. Parking Brake The parking brake should be used whenever you park your vehicle. If the service brakes don’t operate while the vehicle is in motion, you can make an emergency stop with the parking brake,...
Page 161 RWARNING To prevent personal injury, do not release the parking brake while outside the vehicle. RWARNING Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transaxle) or in 1 (First) (manual transaxle). Always check the Brake Warning Light each time you start your engine.
Page 162 Driving Under Special Conditions Tips for Safe Driving As with any new vehicle, yours may drive and handle differently from your previous vehicle. Use particular care until you become accustomed to its various features and driving characteristics. Operate your vehicle within reasonable limits. Sudden acceleration, deceleration, turning, or combinations of these maneuvers can cause a vehicle to behave differently than anticipated.
Page 163 RWARNING To avoid losing control on slippery roads, do not downshift into 1 (First) with the automatic transaxle when moving faster than 20 mph (32 km/h). Do not downshift into 1 (First) with the manual transaxle when moving faster than 10 mph (16 km/h).
Page 164 High water Do not drive through flooded areas unless you are sure that the water is below the bottom of the wheel rims. If you must drive through high water, drive slowly. You may have limited traction or wet brakes, so allow extra stopping distance because your vehicle will not stop as quickly as usual.
Page 165 RWARNING If the GVWR or the GAWR specified on the Safety Compliance Certification Label is exceeded, your vehicle may be damaged or you may lose control and injure someone. Limiting Your Vehicle’s Load The load you add to your vehicle must not exceed the maximum load stated on the tire information decal.
Page 166 After determining this load, you must also make sure that the total weight of your vehicle, plus the load it carries, is less than its GVWR. Also, make sure that the weight your vehicle carries over each axle is less than the GAWR for the respective axle.
Page 167 Towing a manual transaxle (MTX) equipped vehicle behind another vehicle, such as a Recreational Vehicle (RV), is allowed only if it is towed forward. The parking brake must be released, the gearshift must be in Neutral, the ignition key must be in the ACC position, the battery must be disconnected to eliminate battery drain, and the steering wheel unlocked.
Page 168: Roadside Emergencies
Roadside Emergencies Jump-Starting Your Vehicle Your vehicle has a Motorcraft maintenance-free battery. Your vehicle’s battery may die if you leave the lights on or any electrical equipment on after you turn the engine off. If this happens, you may be able to jump-start from a booster battery to start your vehicle.
Page 169 If the acid touches someone’s skin, eyes, or clothing, immediately flush the area with water for at least 15 minutes. If someone swallows the acid, have him or her drink lots of milk or water first, then Milk of Magnesia, a beaten egg, or vegetable oil.
Page 170 4. Check all battery terminals and remove any excessive corrosion before you attach the jumper cables. 5. Turn on the heater fan in both vehicles. Press the DEFROST button. Turn off all other switches and gauges. Connecting the jumper cables 1.
Page 171 The sequence for connecting the jumper cables Jump-Starting 1. Make sure that the jumper cables are not in the way of moving engine parts, then start the booster vehicle. Run the engine at a moderate speed. 2. Let the discharged battery charge for a few minutes and then start the disabled vehicle.
Page 172: Changing A Tire
3. When both vehicles are running, let them idle for a few minutes to charge the discharged battery. Removing jumper cables 1. Always remove the jumper cables in reverse order. Remove the negative (-) end of the jumper cable from the metallic surface on the engine or frame of the disabled vehicle.
Page 173 The Temporary Spare Tire You may have a high pressure temporary spare tire. This spare tire is smaller than a regular tire and is designed for emergency use only. Use it only when you get a flat tire and replace it as soon as you can.
Page 174 Spare Tire Location The temporary spare tire is stored in the luggage compartment, under the mat and floorboard. Location of the temporary spare tire and jacking equipment To remove the jack and the temporary spare, turn the bolt counterclockwise. Preparing to Change the Tire 1.
Page 175 Blocking the wheel diagonally opposite the tire being changed When one of the front wheels is off the ground, the transaxle alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park) or 1 (First). To prevent the vehicle from moving when you change one of the front tires, put a block behind the wheel that is diagonally opposite to the tire.
Page 176 4. Loosen the wheel lug nuts by pulling up on the handle of the wrench one half-turn counterclockwise. Do not remove the wheel lug nuts until you raise the tire off the ground. For information about removing anti-theft lug nuts, see Removing and Replacing the Anti-Theft Wheel Lug Nuts in this section.
Page 177 Jack mounting position 2. Remove the lug nuts by using the lug wrench. Never loosen the hub nuts. See the following illustration if you are not sure where to find the lug nuts.
Page 178 Lug nut positions 3. Replace the flat tire with the spare tire. 4. Replace the lug nuts and tighten snug. The beveled edge faces inward. Do not fully tighten the lug nuts until you lower the vehicle. If you do, you could force the vehicle off the jack.
Page 179 RWARNING Installation of an English thread nut on a metric stud (or vice-versa) will not properly secure the wheel to the hub. Damaged studs may result in wheel separation and possible injury. 5. Lower the vehicle by turning the jack handle counterclockwise.
Page 180: Towing Your Vehicle
When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for the proper hook-up and towing procedures for your vehicle.
Page 181 Towing With the Back Wheels Off the Ground For automatic and manual transaxle vehicles, if it is necessary to tow your vehicle from the rear (with the rear wheels off the ground), a dolly must be placed under the front tires to prevent transaxle damage.
Page 182 Do not use your vehicle’s steering column lock to secure the wheels in a straight-ahead position. Always use a steering wheel clamping device designed for towing service. Refer to Towing behind another vehicle — recreational vehicle in the Index for information on towing behind an RV.
Page 183: Customer Assistance
Customer Assistance Roadside Assistance Ford Motor Company has set up a 24-hour, seven-day-a-week hotline with trained operators that put you in touch with the help you need if you experience a problem with your vehicle. This complimentary service is provided to you throughout your warranty period of 3 years or 36,000 miles (60,000 km), whichever comes first.
Page 184 1-800-241-FORD (in Canada call 1-800-665-2006). If You Have a Service Problem Ford Motor Company has authorized Ford and Lincoln-Mercury dealerships that can service your vehicle for you. This chapter tells you how to get service or maintenance for your vehicle.
Page 185 If you are away from home when your vehicle needs to be serviced, or if you need more help than the dealer gave you, contact the Ford Customer Assistance Center to find an authorized dealership that may be able to help.
Page 186: The Dispute Settlement Board
What Kind of Cases Does the Board Review? The Board reviews all product performance and service complaints on Ford, Mercury and Lincoln Cars and Ford and Mercury Light Trucks under warranty that have not been resolved by a dealer or Ford Motor Company, except those involving:...
Page 187 How Does the Board Work? The Board has four members: three consumer representatives a Ford or Lincoln-Mercury dealer Consumer candidates for Board membership are recruited and trained by an independent consulting firm. Dealers are chosen because of their business leadership qualities.
Page 188 The decisions of the Board are binding on the dealer and Ford, but customers may have other options available to them under state or federal law. The decisions of the Board, however, may be...
Page 189 Board address. At the same time, your dealer and Ford Motor Company representative are asked to submit statements. To review your case properly, the Board needs...
Page 190: Reporting Safety Defects
National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 191 If a specific item of concern arises, where a solution cannot be reached between a vehicle owner, Ford of Canada, and/or one of its dealers (that all parties can agree upon), the owner may wish to use the services offered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 192 Use of leaded fuel in your vehicle without a proper conversion may damage the effectiveness of your emissions control system and may cause engine knocking or serious engine damage. Ford Motor Company is not responsible for any damage that is caused by use of improper fuel.
Page 193 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write to: If you are in other foreign countries, contact the nearest Ford dealership.
Page 194: Accessories
Accessories Ford Accessories for Your Vehicle Ford has many fine products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following, or products of equivalent quality: A wide selection of accessories is available through your local authorized dealer.
Page 195 Comfort and Convenience Protection and Appearance NOTE: When adding accessories, equipment, passengers, and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR, GAWR as shown on the Safety Compliance Certification Label).
Page 196 5 watts or less will not ordinarily affect your vehicle’s operation.) NOTE: Because we have no control over the installation, design, or manufacture of such systems, Ford cannot assume responsibility for any adverse effects or damage that may result if you use this equipment.
Page 200: Servicing Your Probe
Servicing Your Probe Service Made Easy Ford has two goals for servicing your vehicle. 1. When we can, we design parts that do not need to be serviced. 2. We want to make servicing your vehicle as easy as possible. To help you:...
Page 201 Use only recommended fuels, lubricants, fluids, and service parts that meet Ford Motor Company specifications. Motorcraft parts are designed and built to provide the best performance in your vehicle. Using these parts for replacement is your assurance that Ford-built quality stays in your vehicle.
Page 202 RWARNING The cooling fan is automatic and may come on at any time. Always disconnect the negative terminal of the battery before working near the fan. If you must work with the engine running, avoid wearing loose clothing or jewelry that could get caught in moving parts.
Page 203 Working with the engine on: 1. Set the parking brake fully and make sure the gearshift is securely latched in P (Park) (automatic transaxle) or Neutral (manual transaxle). 2. Block the wheels. This will prevent your vehicle from moving unexpectedly. RWARNING Do not start your engine with the air cleaner removed and do not remove it...
Page 204 The hood release handle NOTE: Apply lubricant to the hood latch at six-month intervals to maintain smooth and trouble-free operation. NOTE: Read and understand Precautions When Servicing Your Vehicle at the beginning of this chapter before opening the hood. Engine Types Your vehicle has one of these types of engines: a 2.0L (121 CID) fuel injected 16-valve four-cylinder engine.
Page 207: Filling The Fuel Tank
Cleaning the Engine A clean engine is more efficient because the engine is able to cool properly. A build up of grease and dirt acts as an insulator, keeping the engine warmer than normal. Extreme care must be used if a power washer is used to clean the engine.
Page 208 Manual fuel filler-lid override (behind left rear trim panel in hatch) To fill the fuel tank: 1. After opening the fuel filler door, remove the cap carefully and slowly by turning it counterclockwise 1/2 to 3/4 turn. RWARNING The fuel system may be under pressure. If the fuel cap is venting vapor or if you hear a hissing sound while disengaging the fuel cap, wait until it stops before...
Page 209 NOTE: If you spill any fuel on the body of your vehicle, clean it off immediately. The fuel may dull or soften the paint if you do not wash it off. 3. Replace the fuel cap completely when you are finished. Turn it clockwise 1/4 turn until it is tight.
Page 210 Octane recommendations Your engine is designed to use fuel with an octane rating of 87. In most cases it is not necessary to use a fuel with an octane rating higher than 87. At service stations, the octane rating is displayed in a label on the pumps. Your 2.5L engine is designed to use fuel with an octane rating of 91 or higher.
Page 211 If your vehicle has problems with starting, rough idle or hesitation problems when the engine is cold, it may be caused by fuel with low volatility. Try a different brand of fuel. If the condition persists, see your dealer or a qualified service technician.
Page 212 RWARNING Gasoline or gasoline blended with methanol can cause blindness and possible death when swallowed. If any fuel is swallowed, call a physician or poison control center immediately. Avoid breathing vapors while refueling. If fuel is splashed on the skin, wash with soap and water.
Page 213 Fuel Economy Fuel economy is an estimate of the efficiency of your vehicle and can be calculated as Miles Per Gallon (MPG) or Liters Per 100 Kilometers (L/100K). Do not calculate fuel economy during your vehicle’s break-in period. This would not be an accurate estimate of how much fuel your vehicle will normally use.
Page 214 Aftermarket add-ons such as bike, ski or luggage racks, bug deflectors, etc. Engine Oil Recommendations We recommend using Motorcraft oil or an equivalent oil meeting Ford Specification ESE-M2C153-E and displaying the American Petroleum Institute CERTIFICATION MARK on the front of the container.
Page 215 Never use: “Non-Detergent” oils Oils labeled API SA, SB, SC, SD, SE, SF or SG Additional engine oil additives, oil treatments or engine treatments Engine oils with an SAE 5W-30 viscosity are PREFERRED for your vehicle. They provide the best engine performance, fuel economy and engine protection for all climates down to -15˚F (-25˚C).
Page 216 5. Wipe the dipstick clean and put it back into position, making sure it is fully seated. Engine oil dipstick 6. Carefully, pull the dipstick out again. If the oil level is below the L line, add engine oil as necessary. If the oil level is beyond the letter F, engine damage or high oil consumption may occur and some oil must be removed from the engine.
Page 217 Changing the Engine Oil and the Oil Filter Change the engine oil and oil filter per the following, whichever occurs first. Refer to the Maintenance Schedule and Record booklet for additional information. NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for disposing of these types of fluids.
Page 218: Engine Coolant
Engine Coolant Checking the engine coolant NOTE: Be sure to read and understand Precautions When Servicing Your Vehicle at the beginning of this chapter. RWARNING The cooling fan is automatic and may come on at any time. Always disconnect the negative terminal of the battery before working near the fan.
Page 219 — not to the radiator. If the coolant level is low, add to the engine coolant recovery reservoir container a 50/50 mixture of water and the type of coolant that Ford specifies. Check the coolant level again the next few times you drive your vehicle.
Page 220 RWARNING Never remove the radiator cap or the coolant system cap while the engine is running or hot to avoid personal injury. 2.5L Engine Before removing either cap, turn the engine off and let it cool. Even when the engine is cool, be careful when removing the caps.
Page 221 Ford Premium Cooling System Fluid is an optimized formula that will protect all metals and rubber elastomers used in Ford engines for four years or 50,000 miles (80,000 km). It is not necessary and not recommended to use supplemental coolant additives in your vehicle.
Page 222 NOTE: Do not use an engine coolant that does not meet all 14 requirements of Ford specification ESE-M97B44-A. The use of an improper coolant may void your warranty for the engine cooling system.
Page 223 Use Ford Premium Cooling System Fluid or an equivalent engine coolant that meets Ford Specification ESE-M97B44-A. Do not use alcohol or methanol antifreeze and do not use engine coolant mixed with alcohol or methanol antifreeze. If you do not use the proper coolant, the aluminum radiator on your vehicle will corrode.
Page 224 Refilling the engine coolant — 2.0L engine When the entire engine cooling system is to be drained and refilled, use the following procedure: 1. Remove the radiator cap. 2. With the engine off and cool, add a 50/50 mixture of recommended engine cooling system fluid and water until the radiator is full.
Page 226 4. Replace the radiator breather cap and the coolant system cap and tighten to the first stop. 5. Start and idle the engine until the radiator upper hose is warm. The warm hose indicates the thermostat is open and the engine coolant is flowing through the entire system.
Page 227 Windshield washer fluid reservoir RWARNING Do not put windshield washer fluid in the container for the engine coolant. Use specially formulated windshield washer fluid rather than plain water, because specially formulated washer fluids contain additives that dissolve road grime. For safety reasons, washer fluids containing an appropriate antifreeze such as methanol should be used in freezing weather (temperatures below 32˚F [0˚C]).
Page 228 Wiper blade maintenance Check the windshield wiper blades at least twice a year. Also check them whenever they seem less effective than usual. Such substances as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades.
Page 229 3. Attach a new wiper blade to the wiper arm and press it into place until you hear it click. Replacing the wiper blades Tires Look at your tires each time you fill your fuel tank. If one tire looks lower than the others, check the pressure in all of them.
Page 230 Drive at safe speeds. If you do not take these precautions, your tires may fail or go flat. Ford Motor Company recommends obeying posted speed limits. RWARNING Driving too fast for conditions creates the possibility of loss of vehicle control.
Page 231 Inspect the tire sidewalls for cuts, bruises and other damage. If you suspect internal damage to the tire, have it removed and checked. You may need to repair or replace it. Tire Rotation Because your vehicle’s front and rear tires perform different jobs, they often wear differently.
Page 232 Replace any tires that show wear bands. When your tire shows a wear band, it has only 1/16 inch (2 mm) of tread left. A worn-out tire Because your vehicle’s tires may wear unevenly, you may need to replace them before a wear band appears across the entire tread.
Page 233 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation — Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 234 Traction A B C The traction grades, from highest to lowest, are A, B, and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Page 235 Snow tires During the winter months in some climates, you may need to use snow tires and occasionally chains for your tires. RWARNING Snow tires must be the same size and grade as the tires you currently have on your vehicle. Use chains on the tires only in an emergency or if the law requires them where you live.
Page 236 Tire chains may affect vehicle handling. Drive carefully and avoid hard braking. Do not use chains on temporary spare tires. They may damage the vehicle and the tire. Remove tire chains at the first opportunity after using them on snow and ice. Do not use the chains on dry roads.
Page 237 soda and water. Reinstall the cables when you are done cleaning them, and apply a small quantity of grease to the top of each battery terminal to help prevent corrosion. Battery replacement When the original equipment maintenance-free battery is replaced under warranty, it may be replaced by a low-maintenance battery.
Page 238 Help Us Protect Our Environment Ford Motor Company strongly recommends that used lead-acid batteries be returned to an authorized recycling facility for disposal. Battery recycling symbol...
Page 239: Automatic Transaxle Fluid
If the acid touches someone’s skin, eyes, or clothing, immediately flush the area with water for at least 15 minutes. If someone swallows the acid, have him or her drink lots of milk or water first, then Milk of Magnesia, a beaten egg, or vegetable oil.
Page 240 The fluid level must be above the lower mark. If it is not, you should not drive your vehicle until more fluid is added. Ideally, the fluid level should be within the specified area of the dipstick. NOTE: The fluid level indication on the dipstick will be different at operating temperature and room temperature.
Page 241 Manual Transaxle Fluid The lubricant level and quality should not deteriorate under normal use. However, you should periodically have your Ford Dealer check the fluid level during regular oil changes. NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for...
Page 242 Constant Velocity Joints Inspect all rubber boots for signs of cracks, tears, or splits. Inspect underneath of your car for any indication of grease splatter in the areas of constant velocity joint boots, outboard and inboard locations; grease splatter is an indication of boot and/or clamp damage.
Page 243 Brake fluid level If the fluid is low, carefully clean and remove the cap from the reservoir. Fill the reservoir to the MAX line with Ford High Performance DOT 3 Brake Fluid C6AZ-19542-AA or DOT 3 equivalent fluid meeting Ford specification ESA-M6C25-A.
Page 244: Power Steering Fluid
Power Steering Fluid Check the level of the power steering fluid at least twice a year (i.e., every Spring and Fall). Checking and Adding Power Steering Fluid 1. Start the engine and let it run until the power steering fluid reaches normal operating temperature.
Page 245 4. Remove the dipstick to read the power steering fluid level. If the power steering fluid is low, add fluid in small amounts, continuously checking the level, until you reach the HIGH line. Do not overfill. To find out how much fluid your vehicle’s power steering fluid reservoir will hold, see Refill capacities for fluids in the Index.
Page 246 Fuse panel under instrument panel Inside of the instrument fuse panel cover...
Page 248 Fuse panel located under hood Fuse panel cover located under the hood...
Page 252 To remove and replace a fuse, use the fuse puller provided. Fuse puller tool and fuse RWARNING Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Page 253 Headlamp Bulb Your vehicle has retractable halogen headlamps. If you need to replace a headlamp, have it done by a Ford service technician.
Page 254 High-Mount Brakelamp Bulb To replace the bulb: 1. Remove the two side trim liftgate panels. 2. Remove the liftgate trim clip and the liftgate trim. 3. Remove the bulb from the socket by pushing it in and turning it counterclockwise. 4.
Page 255 Rear Lamp Bulbs To replace a bulb: 1. Remove the attaching screw and the rear lens cover. Removing the attaching screw and lens 2. Partially remove the rear lens by pulling the lock tabs out of the slots.
Page 256 Pulling out the lock tabs 3. Turn the socket counterclockwise to remove it from the lens. 4. Remove the bulb from the socket by pushing it in and turning it counterclockwise.
Page 257 The rear lamps 5. Install the bulb by pushing it into the socket and turning it clockwise. 6. Install the socket by pushing it into its housing and turning it clockwise. The arrow on the socket must align with the arrow on the housing when installed.
Page 258: Emission Control System
Bulb Specifications Emission Control System Your vehicle is equipped with a catalytic converter which enables your vehicle to comply with applicable exhaust emission requirements. RWARNING Exhaust leaks may result in the entry of harmful and potentially lethal fumes into the passenger compartment. Under extreme conditions excessive exhaust temperatures could damage the fuel system, the interior floor covering, or...
Page 259 In general, maintenance, replacement, or service of the emission control devices or systems in your new Ford Motor Company vehicle or engine may be performed at your expense by any automotive repair establishment or individual using automotive parts equivalent to...
Page 260 If other than Ford or Motorcraft or Ford authorized remanufactured parts are used for maintenance, replacement, or for the service of components affecting emission control, the owner should be assured that such parts are warranted by their manufacturer to be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 261 Readiness for Inspection/Maintenance Testing In some localities it may become a legal requirement to pass an Inspection/Maintenance (I/M) test of the On-Board Diagnostic (OBD) II system. If the vehicle’s powertrain system or its battery has just been serviced, the OBD II system is reset to a not ready for I/M testing condition.
Page 262 The engine must be warmed up and at operating temperature before proceeding with the drive modes of the following OBD II Drive Cycle. 1. Start the engine. Drive or idle (in neutral) the vehicle for 4 minutes. 2. Idle the vehicle in drive (neutral for automatic transaxles) for 40 seconds.
Page 263 8. Drive vehicle and hold the throttle steady at the selected speed between 45 and 60 mph (72-97 km/h) (manual transaxles use 5th gear) for approximately 5 minutes. 9. Drive the vehicle for 5 minutes at varying speeds between 45 and 60 mph (72-97 km/h) (manual transaxles use 5th gear).
Page 265 However, when refilling or adding is required, it should be with the proper lubricant or fluid meeting Ford technical specifications. See the Maintenance Schedule and Record booklet for instructions on maintaining proper fluid levels.
Page 268: Vehicle Storage
Vehicle Storage Maintenance Tips If you plan on storing your vehicle for an extended period of time (60 days or more), refer to the following maintenance recommendations to ensure your vehicle stays in good operating condition. General Store all vehicles in a dry, ventilated place. Protect from sunlight, if possible.
Page 269 Ford Gas Stabilizer should be added whenever actual or expected storage periods exceed 60 days. Follow the instructions on the label. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system.
Page 270 Brakes Make sure brakes and parking brake are fully released. Tires Maintain recommended air pressure. Miscellaneous Make sure all linkages, cables, levers and clevis pins under vehicle are covered with grease to prevent rust. Move vehicles at least 25 feet (10 m) every 15 days to lubricate working parts to prevent corrosion.
Page 282: Index
Index ABS warning light (see Anti-lock brake system) ..57 Additives, engine oil ..Air bag supplemental restraint system... 17, 25 and child safety seats .
Page 283 Automatic transaxle driving with ... . . fluid, adding ... . . fluid, checking ... . Backing up .
Page 284 Canada, customer assistance ..Canada, warranty information ..Canadian Motor Vehicle Arbitration Plan (CAMVAP)....Carbon monoxide in exhaust ..48 Car seats for children (see Child safety seats) .
Page 285 Cruise control (see Speed control) ..89 Customer Assistance Center, Ford (U.S.) ....Customer Assistance Centre, Ford of Canada ... .
Page 286 Dispute Settlement Board ..Doors ....95 Driving under special conditions bad weather ... . . heavy load .
Page 287 ....Exhaust fumes ....48 Extended Service Plan, Ford ..Federal Communications Commission . . .
Page 288 Ford of Canada Customer Assistance Centre ... Foreign registration ... French owner guides, how to obtain ..
Page 289 Gauges, Mechanical (continued) odometer ....62 speedometer ....62 tachometer ....62 trip odometer .
Page 290 Identification Number, Vehicle (VIN) . . . Idle relearning ....speed ....45 Ignition positions of the ignition .
Page 291 Lamps (continued) interior lamps....72 replacing bulbs ... . Lane change indicator (see Turn signal) ..77, 83 Lights, warning and indicator air bag .
Page 292 Mileage, calculating fuel economy ..Mirrors, remote control ..Moon roof ....Motorcraft parts... . . National Highway Traffic Safety Administration .
Page 293 Radio (see Electronic sound systems) . . . Rear window ....Remote entry system replacement/additional transmitters. . . replacing the batteries ..99 Reporting safety defects .
Page 294 Seat belts (see Safety restraints)..Seats child safety seats ... . 24 folding rear seats ... head restraints .
Page 295 Steering wheel horn ....87 locking ....37 speed controls .
Page 296 Transaxle control switch ..Transmission, automatic operation ..Transmission control switch ..Trip odometer ....62 Tune-up specifications (VECI) .
Page 297 Washer fluid reservoir ....windshield ....Weight limits (GAWR, GVWR) ..Wheel and tire matching .
Page 298: Service Station Information
Service Station Information...

This manual is also suitable for:

Probe gt

Ford Probe Owner's Manual

Quick Links

Related Manuals for Ford Probe

Summary of Contents for Ford Probe

This manual is also suitable for:

Table of Contents