Page 3: Table Of Contents
Table of Contents Introduction ............ 1 Instrumentation ..........7 Electronic Sound Systems ......21 Controls and Features ........ 47 Seating and Safety Restraints ....89 Starting ............125 Driving ............133 Roadside Emergencies ......155 Maintenance and Care ......183 Capacities and Specifications ....
Page 4: Introductory Information
Introductory Information Ford’s Commitment to You At Ford Motor Company, excellence is the continuous commitment to achieve the best result possible. It is dedication to learning what you want, determination to develop the right concept, and execution of that concept with care, precision, and attention to detail.
Page 5 This guide describes equipment and gives specifications for equipment that was in effect when this guide was approved for printing. Ford may discontinue models or change specifications or design without any notice and without incurring obligation. NOTES and WARNINGS NOTES give you additional information about the subject matter you are referencing.
Page 6 If you lose your Warranty Information Booklet, you can get a new one free of charge. Contact any Ford or Lincoln-Mercury dealer, or refer to the addresses and phone numbers on the first page of this owner guide.
Page 7 Buying a Ford Extended Service Plan If you bought your vehicle in the U.S., you can buy a Ford Extended Service Plan for your vehicle. This optional contract provides service protection for a longer period of time than the basic warranty that comes with your vehicle.
Page 8 500 miles/800 km after any wheel change or any other time the wheel lug nuts have been loosened. Use only the type of engine oil that Ford recommends. See Engine oil recommendations in the Index. Do not use special “break-in” oils.
Page 9: Cleaning The Outside Of Your Vehicle
Ford, however, believes that continual improvement in customer satisfaction is a high priority. For this reason, Ford has authorized its dealers to repair, at no charge to the owner,...
Page 10 Introductory Information Cleaning Chrome and Aluminum Parts Wash chrome and aluminum parts with a mild detergent. Do not use steel wool, abrasive cleaners, fuel or strong detergents. Cleaning Plastic Parts Some of your vehicle’s exterior trim parts are plastic. Clean with a tar and road oil remover if necessary.
Page 11: Instrumentation
Instrumentation The instrument panel (dashboard) on your vehicle is divided into several different sections. The illustrations on the following pages show the major parts of the instrument panel that are described in this chapter. Some items shown may not be on all vehicles. In your vehicle, the warning lights and gauges are grouped together on the instrument panel.
Page 14 The instrument cluster on the Probe GT model is similar to the one shown. The two exceptions are: the speedometer on the GT model shows 140 mph (225 km/h) and it has a 7,000 rpm red-line tachometer. GT model speedometer and tachometer The following warning lights and gauges are on the cluster.
Page 15 Indicator Lights and Chimes Safety Belt Warning Light and Chime This warning light and chime remind you to fasten your safety belt. If you do not fasten your safety belt before the ignition is turned to ON, the chime will sound for 4 to 8 seconds and the warning light will illuminate for 1 to 2 minutes, or until the safety belt is fastened.
Page 16 RWARNING If any of these things happen, even intermittently, have the air bag system serviced at your Ford or Lincoln-Mercury dealer immediately. Brake System Warning Light Your vehicle has a divided brake system. If one part isn’t working, the other part can still work and stop you.
Page 17 This light will also illuminate if the parking brake does not release fully. If it does stay on after the parking brake is fully released, it means there may be a brake problem. Pull off the road and stop carefully. You may notice that the pedal is harder to push, the pedal may go closer to the floor, or it may take longer to stop the vehicle.
Page 18 NOTE: If a fault occurs in the anti-lock system, and the brake warning light is not lit, the anti-lock system is disabled but normal brake function remains operational. NOTE: If your vehicle must be jump-started because of a low battery, the Anti-Lock Brake System warning light could remain on.
Page 19 High Beam Light This light illuminates when the headlamps are turned to high beam or when you flash the lights. High beam light Check Engine Warning Light This light illuminates when the electronic engine control system is not working properly. This is the computer that controls the operating conditions of the engine.
Page 20 If the light flashes briefly while you are driving, it means that the condition is no longer present. O/D OFF Light (If equipped) This light tells you that the overdrive off (O/D OFF) button on the shift selector has been pushed.
Page 21 The fuel gauge indicator may vary slightly while the vehicle is in motion. This is the result of fuel movement within the tank. You can get a more accurate reading with the vehicle on smooth, level ground. Charging System Gauge This gauge tells you your battery’s voltage when you turn your ignition key to ON.
Page 22 Engine Coolant Temperature Gauge This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level or mixture, the gauge indication will not be accurate. The pointer usually moves from C (cold) into the NORMAL band as your vehicle warms up.
Page 23 5. Refer to Adding Engine Coolant in the Maintenance and Care chapter. Add as much coolant as your engine needs. If the engine continues to overheat, have the cooling system serviced. Speedometer The speedometer tells you how many miles (kilometers) per hour your vehicle is moving. Odometer The odometer tells you the total number of miles (kilometers) your vehicle has been driven.
Page 25 Compact Disc Radio The Compact Disc Radio combines the Electronic Stereo Radio with the Ford Compact Disc Player. Using the Controls on Your New Radio/CD Player Most of the features of this unit work for both radio and CD operation, depending on which mode the unit is in.
Page 26 How to tune radio stations There are four ways for you to tune in a particular station. You can manually locate the station using the “SCAN/TUNE” button, “SEEK” the station, “SCAN” to the station or select the station by using the memory buttons, which you can set to any desired frequency.
Page 27 Using the “SCAN/TUNE” button to scan radio stations Pressing the “SCAN/TUNE” button once enters the scan mode (display will indicate “SCN”). Pushing the top ( a ) half of the “SEEK” button will begin the scan mode up the frequency band, stopping on each listenable station for approximately five seconds.
Page 28 Using the Automatic Memory Load feature You can activate the Auto Memory Load feature by pressing and holding the “AUTO PRESET” button for approximately three seconds. Auto Memory Load sets all memory buttons in AM, FM1 and FM2 sequentially by seeking out the first five strong stations for the respective band and storing them in memory buttons 1-5.
Page 29 To deactivate the Auto Memory Store mode and return to the manually-set memory button stations (or those stations set using Auto Memory Load), simply push the “AUTO PRESET” button. Display will show “AUTO” then “OFF.” The next time Auto Memory Store is activated on that band, the radio will store the next set of five strong stations.
Page 30 Adjusting speaker fader Fade control allows you to adjust the sound distribution between the front and rear speakers. Push the “AUDIO” button repeatedly until the display reads “FADE.” Push the “+” side of the “VOL” button to shift the sound to the front speakers, and push the “-”...
Page 31 ( a ) half of the “SEEK” button to set minutes. Using the Controls on Your New Compact Disc Player Your new Ford Compact Disc Player is capable of playing 12 cm or 8 cm discs, without an adapter. The player operates when the power is on and a disc is inserted (label side up).
Page 32 How to insert a disc and begin play Insert one disc, label side up into the disc opening. When inserted, the disc automatically loads into the unit and play starts at the beginning of the first track (selection). When the disc reaches the end, the disc player automatically returns to the beginning of the disc and resumes playing.
Page 33 Using the “SEEK” feature The “SEEK” feature allows you to quickly find a particular selection on the disc. Press the bottom ( b ) half of the “SEEK” button once to repeat the current playing selection. Press the top ( a ) half of the “SEEK” button to advance to the next selection.
Page 34 How To Take Care of and Clean Your CD Player and Discs To ensure the continued performance of your Ford Compact Disc Player, carefully read the following precautions: Always handle the disc by its edge. Never touch the playing surface.
Page 35 Do not expose the disc to direct sunlight or heat sources such as defroster and floor heating ducts. Do not leave any discs in a parked car in direct sunlight where there may be a considerable rise in temperature or damage may result.
Page 36 CD format. Because of this, a new disc that is free of dust and scratches could be defective and may not play on your Ford Compact Disc Player. If play does not begin after the CD button is pushed: The radio is not on.
Page 39 Using the Controls on Your New Radio How to turn the radio on and adjust the volume Press the “POWER” button to turn the radio on. Press it again to turn it off. Press the right (+) side of the “VOLUME” button to increase the volume.
Page 40 How to tune radio stations (Stereo Cassette Radio) There are four ways for you to tune in to a particular station. You can manually locate the station by using Automatic Music Search “AMS”, “SEEK” the station, “SCAN” to the station or select the station by using the memory buttons, which you can set to any desired frequency.
Page 41 Using the “SEEK” function This feature on your radio allows you to automatically select listenable stations up or down the frequency band. Press the right a side of the “SEEK” button to select the next listenable station up the frequency band. Press the left b side of the button to select the next listenable station down the frequency band.
Page 42 NOTE: If the vehicle’s battery is disconnected, the clock and station memory preset buttons will need to be reset. Adjusting the tone balance and speaker output of your radio Increasing or decreasing bass response Push the “AUDIO” button repeatedly until the display reads “BASS.”...
Page 43 Adjusting speaker fader Fade control allows you to adjust the sound distribution between the front and rear speakers. Push the “AUDIO” button repeatedly until the display reads “FADE.” Push the right (+) side of the “VOLUME” button to shift the sound to the front speakers, and push the left ( ) side to shift the sound to the rear speakers.
Page 44 Using the Automatic Music Search (“AMS”) function with cassette tape player Press and hold the “AMS” button (“AMS” will appear in the display). Then, push the left h button to rewind to the beginning of the current selection or press the right g button to fast forward to the beginning of the next selection.
Page 45 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford or equivalent cassette cleaning cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 46 Clock Operation How to view the clock mode Press the “CLOCK” button to alternate the frequency and time in the display. In the clock mode, pressing any radio function will automatically display the radio frequency for approximately ten seconds before changing back to the clock mode.
Page 47 2. Terrain The terrain (hilly, mountainous, tall buildings) of the area over which the signal travels may prevent the FM signal from being noise-free. Repeated pops and hisses which are heard during an otherwise clear broadcast can occur near the station because of the “line of sight” characteristic of FM radio waves.
Page 48 displayed frequency does not change. While passing the tower, the station may switch back and forth a few times before returning to the original station. When several broadcast towers are present (common in metropolitan areas), several stations may overload the receiver, resulting in considerable station changing, mixing and distortion.
Page 49 Ask your dealer for a copy of this limited warranty. Service At Ford, we stand behind our audio systems with a comprehensive service and repair program. If anything should go wrong with your Ford audio system, return to your dealer for service.
Page 50: Controls And Features
Controls and Features Your vehicle has a variety of features designed for your comfort, convenience and safety. Read this chapter to find out about standard and optional features. The main controls for the climate control system, clock, and radio are on the instrument panel.
Page 52 NOTE: Any cleaner or polish that increases the gloss (shine) of the upper part of the instrument panel should be avoided. The dull finish in this area is to help protect the driver from undesirable windshield reflection. The Climate Control System Heating Only System (Without Air Conditioning) Function selection...
Page 53 The FLOOR position directs air out the floor outlets and the side window defoggers. Ventilate your vehicle with outside air by choosing the VENT position. Temperature control The air temperature can be adjusted by moving the marker on the temperature control to the red area for warm air, or to the blue area for unheated air.
Page 54 Defrosting the Windshield and Side Windows 1. Turn the function selector control to the defrost position. When V is selected, air is directed to the windshield and side windows. 2. Turn the temperature control to the desired temperature. 3. Set the fan at the desired speed. Heating and Defrosting at the Same Time 1.
Page 55 Tips for controlling the temperature in your vehicle To vary the temperature inside your vehicle, move the temperature selector toward the red area for warmer air and toward the blue area for cooler air. If you drive with the fan off and the windows closed, the windows may fog up.
Page 56 Air Conditioning System (If equipped) Operate the air conditioning by using the climate controls on the center of the instrument panel. Air conditioning controls Sometimes you may notice slight engine surging if you have the air conditioner on. This is normal, as the system is designed to cycle the compressor on and off to maintain desired cooling.
Page 57 If the inside of your vehicle is very warm, drive for a few minutes with the windows down. This forces most of the hot, stale air out of the vehicle and helps the air conditioning cool the vehicle faster. MAX A/C When MAX A/C is selected, cooled interior air is recirculated through the system.
Page 58 You will get better fuel economy without using the air conditioning. Engine Idle Speed Control System Genuine Ford air conditioning (either factory-installed or dealer-installed) has an engine idle speed control system that compensates for engine speed loss that may occur when the air conditioning compressor is running.
Page 59 Rear Window Defroster (If equipped) Rear window defroster button The defroster for the rear window clears frost, fog, or thin ice from both the inside and outside of the rear window. The rear window defroster button is located on the lower right of the instrument panel below the climate control panel.
Page 60 Rear Window Wiper and Washer The rear window wiper and washer buttons are located on the instrument panel below the climate control panel. To operate the rear wiper, push the rear window wiper button. Push the button a second time to turn the wiper off.
Page 61: Interior Lights
Interior Lights Lighting Up the Interior and Instrument Panel With the parking lamps or headlamps on, the brightness of the instrument panel lighting can be adjusted. To brighten or dim the instrument panel lighting, rotate the dimmer control thumbwheel as desired. Dimmer control thumbwheel The dimmer control thumbwheel is located to the left of the steering wheel on the instrument...
Page 62 Interior/map lamp control panel Map lamps (if equipped) The map lamps can be turned on by using the interior/map lamp control panel located between the sun visors. There are two map lamps, one for the driver and one for the passenger. To turn on the map lamp, push the button that is next to the lamp.
Page 63: Electronic Sound Systems
Radio For information about the radio in your vehicle, refer to the Electronic Sound Systems chapter in this Owner Guide. Clock Controls on Electronic Radios The electronic radios have a built-in clock. For complete operating instructions, refer to the Electronic Sound Systems chapter in this Owner Guide.
Page 64 Ignition Understanding the Positions of the Ignition Ignition lock cylinder LOCK locks the steering wheel. It also locks the gearshift lever in P (Park) (automatic transaxle). LOCK is the only position that allows you to remove the key. The LOCK feature helps to protect your vehicle from theft.
Page 65 START cranks the engine. Release the key once the engine starts so that you do not damage the starter. The key should return to ON when you release it. The START position also allows you to test the brake warning light. The Turn Signal Lever You can use the turn signal lever on the left side of the steering column to:...
Page 66 Daytime Running Light System (Canadian vehicles only) In Canada, the lights illuminate during daytime operation. The Daytime Running Light system (DRL) automatically illuminates when the ignition switch is turned to the ON position. The daytime running lights are switched off under the following conditions: when the headlamps are switched on when the parking brake is applied...
Page 67 Open the main fuse panel. Refer to the underhood fuse panel in Servicing Your Probe later in this owner guide. Pull the RETRA (20A) fuse straight out. Inspect the removed fuse. If it is blown, replace it with a new one of the same rating. If it isn’t...
Page 68 Manual headlamp retractors located behind the headlamps High Beams and Flashing the Lamps To turn on the high beams, turn the headlamp control knob to the headlamp ON position and push the turn signal lever away from you until it latches. When the high beams are ON, the high beam indicator light on the instrument panel comes on.
Page 69 Flashing the Lights To flash the headlamps, pull the lever toward you for a moment and then release it. The headlamps will flash whether the headlamp knob is in the on or off position. Highbeam and flash-to-pass operation If the headlamps are retracted when you pull the lever toward you, they will pop up and flash.
Page 70 Turn Signals Move the lever up to signal a right turn. Move it down to signal a left turn. The corresponding indicator light in the instrument cluster will flash. If the turn signal stays on after you turn, move the lever back to the center (OFF) position. For lane changes, move the lever far enough to signal but not to latch.
Page 71: Windshield Wipers And Washer
Windshield Wipers and Washer To operate the windshield wipers and washers, make sure your ignition key is turned to the ON position. The windshield wipers have two speeds. To operate the wipers, pull down the lever on the right side of your steering column. The first position is LO (Low) and the second position is HI (High).
Page 72 Interval Wipers (If equipped) In addition to two speed wipers, your vehicle may have wipers that you can set to operate at varying intervals. For example, you can set the interval so they wipe less often when it drizzles and more often in heavier rain. Variable interval wiper control To set the interval wipers, pull the lever down to the first position.
Page 73 If the washer does not work, check the washer fluid level visually and fill if needed. See Servicing Your Probe later in this owner guide. If there is fluid in the reservoir, and your washer doesn’t work, consult your Ford or Lincoln-Mercury dealer.
Page 74: Tilt Steering Column
Tilt Steering Column (If equipped) WARNING Never adjust the steering wheel when the vehicle is moving. To change the position of the steering column/wheel, pull the release lever on the column toward you. Tip the steering wheel to the desired position. Release the lever to lock the steering wheel in place.
Page 75 Speed Control (If equipped) Speed control switches on the steering wheel To Turn Speed Control Off Press OFF, or Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To Turn Speed Control On Press ON To Set a Speed Press SET ACC.
Page 76 Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill in j (Overdrive), you may want to shift to the next lower gear to reduce your vehicle’s speed.
Page 77 To Disengage Speed Control Depress the brake pedal, or Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed. To Return to a Set Speed Press RSM. For RSM to operate, the vehicle speed must be faster than 30 mph (48 km/h).
Page 78 Sliding moon roof control switch Press the switch until the moon roof is opened to the desired position. When you release the switch, the moon roof will stop sliding open. To close the moon roof, press the other side of the switch and hold it until the roof is closed to the desired position.
Page 79 Doors The inside of the door If you close the door with the lock button depressed, the door will remain locked. Power Door Locks (If equipped) If your vehicle has power door locks, the controls to lock the doors are below the inside door handles on each door.
Page 80 Power locks on the driver’s door Windows Using the Power Windows (If equipped) Each door has a power control that opens and closes the window on that door. The driver’s door has a master control panel that operates both windows. To use your power windows, your ignition switch must be placed in the ON position.
Page 81 WARNING Do not let children play with the power windows. Master window control on the driver’s door Mirrors WARNING The right side view mirror makes objects appear smaller and farther away than they actually are.
Page 82 Dual-Electric Remote Control Mirrors (If equipped) Dual-electric remote control mirrors are collapsible. The mirror heads can be folded rearward to prevent damage when using an automatic car wash. To adjust the side mirrors: 1. Locate the control switch in the power control panel on the driver’s door.
Page 83: Storage Compartments
Console A fully-equipped console on your vehicle will include the following items: ashtray and lighter parking brake lever cupholder or storage compartment with cupholder Storage Compartments Your vehicle may have several small storage compartments: a glove compartment that locks and unlocks using the ignition key two map pockets on the door panels (if equipped)
Page 84 Center Console Storage (If equipped) To open the center console storage bin, push the button and slide the lid back. When it is back as far as it will go, push the button and lift the lid. Cupholders The cupholders are located inside the center console storage bin.
Page 85 Hatchback Opening and Closing the Hatchback To open the hatchback from the outside: 1. Put the key into the lock located on the right side, in the tail lamp just above the bumper. 2. Turn the key to the right to unlock. 3.
Page 86 Using the Remote Control for the Hatchback To release the hatchback from inside the vehicle, simply pull up on the remote release lever, which is located in front of the driver’s seat, near the door. Remote control for the hatchback Using the Luggage Compartment Cover This cover lets you conceal cargo in the luggage compartment.
Page 87 To remove the luggage compartment cover: 1. Raise the hatchback to the fully open position. 2. Standing outside the vehicle, unfasten the lift cords from the hatchback lid. 3. Disconnect the two front package tray lift cords from the lower trunk side trim. 4.
Page 88 WARNING The cover may cause injury in a sudden stop or accident if it is not securely installed. To install the luggage compartment cover: 1. Raise the hatchback to the fully open position. 2. From outside the vehicle, position the cover in its sockets.
Page 89 By pressing the UNLOCK button on the transmitter once, you can unlock the driver side door. Pressing the UNLOCK button a second time within five seconds of unlocking the driver’s door will unlock the other doors. You can lock all your vehicle doors by pressing the LOCK button.
Page 90 Replacement batteries can be purchased at most pharmacies, watch stores or at your Ford or Lincoln-Mercury dealer. NOTE: The operating range of the remote entry system can also be affected by...
Page 91 The transmitter can be snapped apart to replace the batteries by twisting a thin coin between the two halves of the transmitter. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. Carefully remove the old batteries. When installing the new batteries, be sure to place the positive (+) side down as marked.
Page 92: Seating And Safety Restraints
Seating and Safety Restraints Seats RWARNING Never adjust the driver’s seat or seatback when the vehicle is moving. RWARNING Always drive and ride with your seatback upright and the lap belt snug and low across the hips. RWARNING Children should always ride with the seatback in the fully upright position.
Page 94 To move the seat forward or backward: Manual seat controls for front seats...
Page 95 To recline the seatback:...
Page 96 To gain access to the rear seat on the driver’s or passenger’s side: Seatback release lever for rear seat access The seatback will return to its set reclined position when pushed back. RWARNING Check to see that the seat and seatback are latched securely in position.
Page 97 To inflate the driver’s seatback lumbar support (if equipped) for lower back support, or to inflate the driver’s seatback side bolster supports (if equipped):...
Page 98 Six-Way Power Seat Adjustment (if equipped) The six-way power seat control lever is located on the outermost side of the driver’s seat.
Page 99 Your seat cushion power adjust lever is operated by a motor. To avoid damage to the motor, you should avoid operating this feature for an extended period of time. You should also avoid using the six-way power adjust lever continuously with the engine stopped. This could run down the battery.
Page 100 To lower the rear seatback: To raise the seatback, lift the seatback rearward until it latches. Make sure the seatback is locked in position by pushing it forward and backward. RWARNING Check to see that the seat and seatback are latched securely in position. Keep floor area free of objects that would prevent proper seat engagement.
Page 101 RWARNING Cargo should always be secured to prevent it from shifting and causing damage to the vehicle or harm to passengers. RWARNING Do not remove the floor carpet in your vehicle. Emission controls cause high exhaust temperatures under the floor. NOTE: When returning the folding seats to the upright position, remember to return rear shoulder belts to their proper...
Page 102 3) Never use a single belt for more than one person. RWARNING Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Safety belt assemblies...
Page 103: Combination Lap And Shoulder Belts
RWARNING Children should always ride with the seatback in the fully upright position. RWARNING Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. RWARNING Lock the doors of your vehicle before driving to lessen the risk of the door...
Page 104 Fastening the front seat combination lap and shoulder belt NOTE: Be sure to read and understand Important Safety Belt Information in this chapter. Unfastening the combination lap and shoulder belt — front and rear seating positions While the belt retracts, guide the tongue to its original position to prevent it from striking you or the vehicle.
Page 105 Lap/Shoulder Belt Retractors (Dual Locking Modes) Your vehicle is equipped with a dual locking mode retractor on the shoulder belt portion of the combination lap/shoulder safety belt for passengers. Dual locking mode retractors operate in two ways: Vehicle sensitive (emergency) locking mode In this operating mode, the shoulder belt retractor will allow the occupant freedom of movement, locking tight only on hard braking,...
Page 106 This mode must be used when installing a child seat. To switch the retractor from the emergency locking mode to the automatic locking mode, perform the following steps: 1. Buckle the lap/shoulder combination belt. 2. Pull on the belt until all of the stored belt is out of the retractor and a click is heard.
Page 107: Safety Belt Maintenance
(if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after any collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision...
Page 108 RWARNING Do not attempt to service, repair, or modify the air bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. RWARNING If you are close to an inflating air bag, it could seriously injure you.
Page 109 Children and Air Bags NOTE: For additional important safety information on the proper use of seat belts, child seats, and infant seats, please read the entire Safety Restraints chapter in this owner guide. RWARNING Children should always wear their safety belts.
Page 110 If the vehicle is in a moderate or severe frontal collision, the system is activated and the air bags inflate rapidly. After the air bag inflates, it will quickly deflate. After the air bag deployment, you may notice a smoke-like, powdery residue or smell the burnt propellant.
Page 111 RWARNING Several air bag system components get hot after inflation. Do not try to touch them after inflation. RWARNING The air bag will inflate only once. The system is designed to function on a one-time-only basis. If the air bag is inflated, THE AIR BAG WILL NOT FUNCTION AGAIN AND MUST BE REPLACED IMMEDIATELY.
Page 112 Inflated driver-side air bag Inflated passenger-side air bag...
Page 113 If any of these things happen, even intermittently, have the Air Bag Supplemental Restraint System serviced at your Ford or Lincoln-Mercury dealer immediately. Unless serviced, the system may not function properly in the event of a collision.
Page 114: Safety Restraints For Children
Safety Restraints for Children In the U.S. and Canada, you are required by law to use safety restraints for children. If small children ride in your vehicle — this generally includes children who are four years old or younger and who weigh 40 pounds (18 kg) or less —...
Page 115 When possible, put children in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating positions. RWARNING Failure to follow all instructions on the proper use of child seats or the vehicle restraint systems can result in serious injury or death in the event of a sudden...
Page 116 Always follow the safety seat manufacturer’s instructions when installing and using the safety seat. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 117 RWARNING If you do not properly secure the safety seat, the child occupying the seat may be injured during a collision or sudden stop. An unsecured safety seat could also injure other passengers. RWARNING Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle.
Page 118 If you choose to install a child safety seat in the front seat, move the seat as far back as possible. 1. Position the child seat or infant carrier on the passenger seat of the vehicle. 2. Pull down on the shoulder belt, then grasp the shoulder belt and lap belt together.
Page 119 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. Routing safety belt through child seat or infant carrier...
Page 120 Buckling the belt...
Page 121 4. Grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. At this time, the retractor is in the automatic locking mode (child seat restraint mode). Setting the retractor to automatic locking mode...
Page 122 5. Allow the belt to retract. Pull up on the shoulder webbing. A clicking sound will be heard as the belt retracts. This indicates that the retractor is in the automatic locking mode. Push down on the child seat while you pull up on the belt webbbing to remove any slack in the belt.
Page 123 6. Before placing the child in the child seat or infant carrier, forcibly tilt the seat from side to side, and tug it forward to make sure that the seat is securely held in place. Checking that the seat is secure...
Page 124 7. Double check that the retractor is in the automatic locking mode. Try to pull more belt out of the retractor. If you cannot, the belt is in the automatic locking mode. Checking the retractor 8. Check to make sure that the child seat or infant carrier is properly secured prior to each use.
Page 125 RWARNING Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. Attaching Safety Seats With Tether Straps Some manufacturers make safety seats that include a tether strap that goes over the back of...
Page 126 Tether Anchorage Hardware Tether anchor hardware kits can be obtained at no charge from any Ford or Lincoln-Mercury dealer. Be sure to follow the child safety seat manufacturer’s instructions.
Page 127 3. Install the hardware for anchoring the tether following the instructions in the tether anchorage hardware kit. 4. Re-install luggage compartment cover. Installing the anchor bracket...
Page 128: Starting
Starting Fuel-Injected Engines When starting a fuel-injected engine, the most important thing to remember is to avoid pressing down on the accelerator before or during starting. Only use the accelerator when you have problems getting your vehicle started. See Starting Your Engine in this chapter for details about when to use the accelerator while you start your vehicle.
Page 129 3. If you have an automatic transaxle, make sure that the gearshift is in P (Park) and the parking brake is set before you turn the key. If you have a manual transaxle, make sure that the parking brake is fully set, push the clutch pedal to the floor, and put the gearshift into Neutral before you turn the key.
Page 130 For a cold engine: At temperatures 10˚F (-12˚C) and below: If the engine does not start in fifteen (15) seconds on the first try, turn the key to OFF, wait approximately ten (10) seconds so you do not flood the engine, then try again. At temperatures above 10˚F (-12˚C): If the engine does not start in five (5) seconds on the first try, turn the key to OFF, wait...
Page 131 If the engine does not start after two attempts: 1. Turn the ignition key to the OFF position. 2. Press the accelerator all the way to the floor and hold it. 3. Turn the ignition key to the START position. 4.
Page 132 To turn the heater on, simply plug it into a grounded 110-volt outlet. Ford recommends that you use a 110-volt circuit that is protected by a ground fault circuit interrupter.
Page 133 If the Engine Cranks but Does Not Start or Does Not Start After a Collision The Fuel Pump Shut-off Switch If the engine cranks but does not start or does not start even after a small collision, the fuel pump shut-off switch may have been activated. The shut-off switch is a device intended to stop the fuel pump when your vehicle has been involved in a substantial jolt.
Page 134 Have the exhaust and body ventilation systems checked whenever: your vehicle is raised for service the sound of the exhaust system changes your vehicle has been damaged in a collision Improve your ventilation by keeping all air inlet vents clear of snow, leaves, and other debris. If the engine is idling while you are stopped in an open area for long periods of time, open the windows at least one inch (2.5 cm).
Page 135 Removing the Key From the Ignition 1. Put the gearshift selector lever in P (Park) (automatic transaxle) or 1 (First) (manual transaxle). 2. Set the parking brake fully. 3. For a manual transaxle: Push in on the lock cylinder and turn the key from ACC to LOCK.
Page 136: Driving
Driving Brakes Applying the Brakes Your vehicle may have four-wheel power anti-lock disc brakes which adjust automatically through everyday use. Some models have power front disc brakes and rear drum brakes which automatically adjust as the brake pads and linings wear down. If your vehicle does not have anti-lock brakes, apply the brake pedal gradually.
Page 137 Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied. Such noises are usually heard during the first few brake applications in the morning;...
Page 138 If the vehicle has continuous vibration or shudder while braking, mainly in the steering wheel, the vehicle most likely needs service. Ford Motor Company has not found any detrimental effects of popular mobile radio transmitting equipment installed on vehicles...
Page 139 ON position, or during a sudden stop, have your mobile radio dealer inspect the radio installation. Proper radio installation procedures to be followed are published by the radio manufacturer. Parking Brake The parking brake should be used whenever you park your vehicle. If the brakes don’t operate while the vehicle is in motion, you can make an emergency stop with the parking brake, however, the stopping...
Page 140: Steering Your Vehicle
R WARNING To prevent personal injury, do not release the parking brake while outside the vehicle. R WARNING Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transaxle) or in 1 (First) (manual transaxle). Always check the Brake Warning Light each time you start your engine.
Page 141: Driving With An Automatic Overdrive Transaxle
steering system breaks down (or if the engine is turned off), you can steer the vehicle manually but it takes more effort. Never hold the steering wheel to the extreme right or left for more than five seconds if the engine is running.
Page 142 Automatic shift lever Your automatic transaxle vehicle has a console-mounted shift selector lever. You must step on the brake pedal, start the engine, and then push in the thumb button to move the shift selector lever to the position you choose.
Page 143 R WARNING Hold the brake pedal down while you move the gearshift lever from position to position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. Shift-lock System (If equipped) For your safety, the automatic transaxle has a shift-lock system, which prevents shifting the transaxle out of the P (Park) position without depressing the brake pedal when the ignition...
Page 144 Automatic console-mounted gearshift lever NOTE: When the ignition key is in the ACC or LOCK position, the transaxle cannot be shifted from the P (Park) position. If the brake pedal is repeatedly depressed and released when the ignition is in the ON position and the selector lever is in the P (Park) position, a chattering near the gearshift lever may be heard.
Page 145: Roadside Emergencies
NOTE: Your vehicle’s gearshift lever is securely latched in P (Park) if you cannot move it without pushing in the thumb button. Keep the brake pedal depressed while moving your gearshift lever. To make the system more effective, the ignition key cannot be removed unless the gearshift selector lever is in the P (Park) position.
Page 146 Once the gearshift is secure in the desired position, release the brake pedal and use the accelerator as necessary. Driving When to use Overdrive (D with Overdrive activated) Overdrive is the usual driving position for an automatic overdrive transaxle. It works the same way Drive (Overdrive OFF) works, automatically upshifting or downshifting as the vehicle speeds or slows.
Page 147 Overdrive OFF indicator light To return the transaxle to normal operation (1st through 4th gears) press the O/D OFF button again. The O/D OFF button may be used to cancel Overdrive any time the vehicle is being driven. Each time your vehicle is started, the Overdrive system will automatically be in the normal “overdrive on”...
Page 148 When to use 2 (Second) Use Second (2) to help drive up moderately steep hills or when starting on slick surfaces. It prevents the transaxle from frequently shifting up and down. It also gives more engine braking than Overdrive or Drive when going down hills. Do not go faster than 64 mph (102 km/h) with the gearshift in the Second (2) position.
Page 149 Parking Always come to a complete stop before you shift into P (Park). Make sure that the shift selector lever is securely latched in P (Park). This locks the transaxle and prevents the front wheels from rotating. R WARNING Always set the parking brake fully and make sure the gearshift is latched in P (Park).
Page 150: Driving With A Manual Transaxle
Driving with a Manual Transaxle Using the Clutch After the engine starts, allow it to idle for a few seconds. Then, hold your right foot on the brake pedal, push the clutch pedal to the floor with your left foot, and move the shift selector lever into 1 (First) or R (Reverse).
Page 151 Shifting the Gears The gearshift for a manual transaxle is mounted on the floor. The gearshift can be in one of seven possible positions, as shown. Shift pattern Always push the clutch pedal all the way in when you shift. You should upshift according to the speeds given in the chart later in this chapter.
Page 152 Backing up To shift into R (Reverse): 1. Bring your vehicle to a complete stop. 2. Push the clutch pedal in all the way to the floor and hold it. If you do not hold the clutch pedal in all the way, you may hear a grinding noise when you shift.
Page 153 Upshifting For normal acceleration, you should upshift at the following speeds: For cruising, you should upshift at the following speeds. Downshifting When you slow down or climb a steep hill, always downshift before the engine starts to lose power. Downshifting reduces the chance of stalling and gives your vehicle better acceleration to increase speed again.
Page 154 Parking To park your vehicle, shift into 1 (First), set the parking brake fully, and turn off the ignition. WARNING Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully.
Page 155 Limiting Your Vehicle’s Load The load you add to your vehicle must not exceed the maximum load stated on the tire information decal. To figure the weight of your vehicle’s load, add the weights of: the driver and passengers luggage and any other items that you put in your vehicle the weight of any equipment that has been added to your vehicle since it was delivered...
Page 156 After determining this load, you must also make sure that the total weight of your vehicle, plus the load it carries, is less than its GVWR. Also, make sure that the weight your vehicle carries over each axle is less than the GAWR for the respective axle.
Page 157 Towing a manual transaxle (MTX) equipped vehicle behind another vehicle, such as a Recreational Vehicle (RV), is allowed only if it is towed forward. The parking brake must be released, the gearshift must be in Neutral, the ignition key must be in the ACC position, the battery must be disconnected to eliminate battery drain, and the steering wheel unlocked.
Page 158: Roadside Emergencies
Roadside Emergencies Hazard Flasher To alert other drivers to hazardous situations, press the hazard flasher switch on the top of the steering column. All the turn signals will flash on and off at the same time. The flashers will also operate while the brake pedal is applied. To turn the flashers off, press the switch again.
Page 159 Hazard warning flasher switch If the Engine Cranks but Does Not Start or Starting After a Collision The Fuel Pump Shut-off Switch If the engine cranks but does not start or if you have had a collision, the fuel pump shut-off switch may have been triggered.
Page 160 The location of the fuel pump shut-off switch RWARNING If you see or smell fuel, do not reset the switch or try to start your vehicle. Have all the passengers get out of the vehicle and call the local fire department or a towing service.
Page 161 If your engine cranks but does not start after a collision or substantial jolt: 1. Turn the key in the ignition to the LOCK position. 2. Check under the vehicle for leaking fuel. 3. If you do not see or smell fuel, push the red reset button on the fuel pump shut-off switch down.
Page 162 Fuse panel under instrument panel Inside of the instrument fuse panel cover...
Page 164 Fuse panel located under hood...
Page 165 Fuses Fuse panel cover located under the hood...
Page 168 To remove and replace a fuse, use the fuse puller provided. Fuse puller tool and fuse Relays...
Page 170: Changing A Tire
RWARNING Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. To find a fuse’s amperage rating, check the number on the fuse or check the color. Even after you replace a fuse, it may continue to blow if you do not find what caused the overload.
Page 171 The Temporary Spare Tire You may have a high pressure temporary spare tire. This spare tire is smaller than a regular tire and is designed for emergency use only. Use it only when you get a flat tire and replace it as soon as you can.
Page 172 try to repair the temporary spare tire or remove it from its wheel. use the wheel for any other type of vehicle. drive through an automatic car wash with this tire. Because the temporary spare tire is smaller than a conventional tire, it reduces the ground clearance.
Page 173 Preparing to Change the Tire 1. Make sure that your vehicle will not move or roll. If you have an automatic transaxle, put the gearshift in P (Park). If you have a manual transaxle, put the gearshift in 1 (First). Set the parking brake and block the wheel that is diagonally opposite the tire that you are changing.
Page 174 2. Get out the spare tire and jack. 3. Remove any wheelcovers or hubcaps with the tapered end of a wheel nut wrench. Insert the handle of the wrench and twist it against the inner wheelcover flange. Remove any chrome nuts or plastic caps covering the wheel lug nuts.
Page 175 Jack mounting position...
Page 176 2. Remove the lug nuts by using the lug wrench. Never loosen the hub nuts. See the following illustration if you are not sure where to find the lug nuts. Lug nut positions 3. Replace the flat tire with the spare tire. 4.
Page 177: Jump-Starting Your Vehicle
Your vehicle has metric (12 mm) wheel studs and lug nuts. During wheel removal and replacement, make certain that you use the same lug nuts to reinstall the wheel or replace them with nuts of the same metric size and threading. RWARNING Installation of an English thread nut on a metric stud (or vice-versa) will not...
Page 178 RWARNING To protect yourself when charging a battery, always shield your face and eyes. Make sure that you can breathe fresh air. RWARNING Applying too much pressure on the ends when lifting a battery could cause acid to spill. Lift the battery with a carrier or with your hands on the opposite corners.
Page 179 Preparing Your Vehicle 1. Your vehicle has a 12-volt starting system, so you need to use a 12-volt jumper system. You will damage your starting motor, ignition system, and other electrical parts if you connect them to a 24-volt power supply (either two 12-volt batteries in series or a 24-volt generator set).
Page 180 4. Connect the other end of the second cable to a good metallic surface on the engine or frame of the disabled vehicle. RWARNING Do not connect the end of the second cable to the negative ( ) terminal of the battery to be jumped.
Page 181 Jump-Starting 1. Make sure that the jumper cables are not in the way of moving engine parts, then start the booster vehicle. Run the engine at a moderate speed. 2. Let the discharged battery charge for a few minutes and then start the disabled vehicle. It may take a couple of tries before the vehicle starts.
Page 182: Maintenance And Care
When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for the proper hook-up and towing procedures for your vehicle.
Page 183 Towing With the Back Wheels Off the Ground For automatic and manual transaxle vehicles, if it is necessary to tow your vehicle from the rear (with the rear wheels off the ground), a dolly must be placed under the front tires to prevent transaxle damage.
Page 184 Do not use your vehicle’s steering column lock to secure the wheels in a straight-ahead position. Always use a steering wheel clamping device designed for towing service. Refer to Towing behind another vehicle —recreational vehicle in the Index for information on towing behind an RV.
Page 185: Maintenance And Care
Maintenance and Care Service Made Easy Ford has two goals for servicing your vehicle. 1. When we can, we design parts that do not need to be serviced. 2. We want to make servicing your vehicle as easy as possible. To help you:...
Page 186 Use only recommended fuels, lubricants, fluids, and service parts that meet Ford Motor Company specifications. Motorcraft parts are designed and built to provide the best performance in your vehicle. Using these parts for replacement is your assurance that Ford-built quality stays in your vehicle.
Page 187 Do not work on a vehicle in an enclosed space with the engine running, unless you are sure you have enough ventilation. Never get under a vehicle while it is supported only by a jack. If you must work under a vehicle, use safety stands. Keep all lit cigarettes and other smoking materials away from the battery and all fuel-related parts.
Page 188 Opening the Hood 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the hood at the center of the vehicle.
Page 189 NOTE: Apply lubricant to the hood latch at six-month intervals to maintain smooth and trouble-free operation. NOTE: Read and understand Precautions When Servicing Your Vehicle at the beginning of this chapter before opening the hood. Engine Types Your vehicle has one of these types of engines: a 2.0L (121 CID) fuel injected 16-valve four-cylinder engine.
Page 192 Engine Oil Recommendations We recommend using Motorcraft oil or an equivalent oil meeting Ford Specification WSS-M2C153-F and displaying the American Petroleum Institute CERTIFICATION MARK on the front of the container. The API Certification Mark Never use: “Non-Detergent” oils Oils labeled API SA, SB, SC, SD, SE, SF or SG...
Page 193 Checking and Adding Engine Oil Since the proper amount of engine oil is important for safe engine operation, check the oil using the dipstick each time you put fuel in your vehicle. Remember the engine must be off, the oil must be warm and the vehicle must be parked on level ground.
Page 194 6. Carefully, pull the dipstick out again. If the oil level is below the L line, add engine oil as necessary. If the oil level is beyond the letter F, engine damage or high oil consumption may occur and some oil must be removed from the engine.
Page 195: Brake Fluid
(Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced. It is recommended you use the appropriate...
Page 196 Brake fluid level If the fluid is low, carefully clean and remove the cap from the reservoir. Fill the reservoir to the MAX line with Ford High Performance DOT 3 Brake Fluid C6AZ-19542-AA or DOT 3 equivalent fluid meeting Ford specification ESA-M6C25-A.
Page 197: Windshield Washer Fluid
RWARNING Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. Windshield Washer Fluid Washer Fluid Check the level of the windshield washer fluid every time you stop for fuel. The reservoir for the windshield washer fluid is located in the engine compartment.
Page 198: Engine Coolant
RWARNING Do not put windshield washer fluid in the container for the engine coolant. Use specially formulated windshield washer fluid rather than plain water, because specially formulated washer fluids contain additives that dissolve road grime. For safety reasons, washer fluids containing an appropriate antifreeze such as methanol should be used in freezing weather (temperatures below 32˚F [0˚C]).
Page 199 Check the coolant level in the coolant recovery reservoir the next few times you drive the vehicle. If necessary, add enough of a 50/50 mixture of coolant and water to bring the liquid level to the fill line on the reservoir. RWARNING Never remove the coolant recovery cap while the engine is running or hot.
Page 200: Capacities And Specifications
Ford specification ESE-M97B44-A. Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for 4 years or 50,000 miles (80,000 km). Do not use alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze.
Page 201: Power Steering Fluid
Have your dealer check the engine cooling system for leaks if you have to add more than a quart (liter) of engine coolant each month. Severe winter climate If you drive in extremely cold climates (less than 34˚F [ 36˚C]), it may be necessary to increase the coolant concentration above 50%.
Page 202 2. While the engine idles, turn the steering wheel back and forth several times. Make sure that the cap assembly is installed at this time. 3. Turn the engine off and check the level on the power steering reservoir. Where to check for power steering fluid 4.
Page 203: Automatic Transaxle Fluid
Automatic Transaxle Fluid Under normal circumstances, you do not need to check the fluid level of the transaxle, since your vehicle does not use up transaxle fluid. Refer to the Maintenance Schedule booklet for replacement intervals. However, if the transaxle is not working properly —...
Page 204 At normal operating temperature (approximately 20 miles [32 km] of vehicle operation), the level on the dipstick should be within the specified area on the “Safe level when hot” temperature scale. At room temperature, the level should be within the specified area on the “Safe level when cold”...
Page 205 Manual Transaxle Fluid The lubricant level and quality should not deteriorate under normal use. However, you should periodically have your Ford Dealer check the fluid level during regular oil changes. NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for...
Page 206 If you see any corrosion on the battery cables or terminals, remove the cables from the terminal and clean them both with a wire brush. You can neutralize the acid with a solution of baking soda and water. Reinstall the cables when you are done cleaning them, and apply a small quantity of grease to the top of each battery terminal to help prevent corrosion.
Page 207 Help Us Protect Our Environment Ford Motor Company strongly recommends that used lead-acid batteries be returned to an authorized recycling facility for disposal. Battery recycling symbol...
Page 208 If the acid touches someone’s skin, eyes, or clothing, immediately flush the area with water for at least 15 minutes. If someone swallows the acid, have him or her drink lots of milk or water first, then Milk of Magnesia, a beaten egg, or vegetable oil.
Page 209 Wiper blade replacement If the wipers still do not work properly after you clean them, you may need to replace the wiper blade assembly. When replacing the wiper blade assembly always use a Motorcraft part or equivalent. To replace the wiper blades: 1.
Page 210 Replacing the wiper blades Tires Look at your tires each time you fill your fuel tank. If one tire looks lower than the others, check the pressure in all of them. Always follow these precautions: Use an accurate tire pressure gauge. Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 3 miles...
Page 211 Safety Compliance Certification Label. If you do not take these precautions, your tires may fail or go flat. Ford Motor Company recommends obeying posted speed limits. RWARNING Driving too fast for conditions creates the possibility of loss of vehicle control.
Page 212 Tire Inspection and Maintenance Inspect the tire treads, and remove stones, nails, glass or other objects that may be wedged in the tread grooves. Check for holes or cuts that may permit air to leak from the tire, and make the necessary repairs.
Page 213 Replacing the Tires We recommend that you use the same size and type when making tire replacements. The standard model uses P195/65 R14 tires, and the GT model is equipped with P225/50VR16 tires. If your standard model vehicle is equipped with a 3-spoke aluminum wheel, you will need P205/55H R15 tires.
Page 214 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation — Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 215 depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. Traction A B C The traction grades, from highest to lowest, are A, B, and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government...
Page 216 RWARNING The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Snow tires During the winter months in some climates, you may need to use snow tires and occasionally chains for your tires.
Page 217: Filling The Fuel Tank
Put the chains on the front tires tightly with the ends held down securely. Retighten the chains after driving 1/2 mile (1 km). Follow the chain manufacturer’s instructions. Do not drive faster than 30 mph (50 km/h) or the chain manufacturer’s recommended speed limit, whichever is lower.
Page 218 Manual fuel filler-lid override (behind left rear trim panel in hatch) To fill the fuel tank: 1. After opening the fuel filler door, remove the cap carefully and slowly by turning it counterclockwise 1/2 to 3/4 turn. RWARNING The fuel system may be under pressure. If the fuel cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the cap.
Page 219 NOTE: If you spill any fuel on the body of your vehicle, clean it off immediately. The fuel may dull or soften the paint if you do not wash it off. 3. Replace the fuel cap completely when you are finished. Turn it clockwise 1/4 turn until it is tight.
Page 220 refuel, your vehicle can be operated on non-California fuels. However, even though your engine will perform adequately on other gasolines, the performance of the emission control devices and systems may be adversely affected. Repair of damage caused by using a fuel that your vehicle was not designed for may not be covered by your warranty.
Page 221 Cleaner Air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates such as a maximum of 10% ethanol or 15% MTBE. There should be no more than 5% methanol with cosolvents and additives to protect the fuel system.
Page 222 Avoid breathing vapors while refueling. If fuel is splashed on the skin, wash with soap and water. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes, and seek medical attention. Gasoline and gasoline blends may contain small amounts of carcinogens, such as benzene.
Page 223 To calculate fuel economy: 1. Fill the tank completely and record the initial odometer reading. 2. Every time you buy fuel record the amount (in gallons or liters) purchased. 3. After at least three to five tankfuls, fill the fuel tank and record the final odometer reading.
Page 224: Emission Control System
Extended use of the A/C, defroster, rear window defroster and other accessories Underinflated tires Heavy loads Aftermarket add-ons such as bike, ski or luggage racks, bug deflectors, etc. Air Conditioning Refrigerant Whenever service to the air conditioning system is required, make sure the service facility uses a refrigerant recycling system.
Page 225 In general, maintenance, replacement, or service of the emission control devices or systems in your new Ford Motor Company vehicle or engine may be performed at your expense by any automotive repair establishment or individual using automotive parts equivalent to those with which your vehicle or engine was originally equipped.
Page 226 By law, anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles is not permitted to intentionally remove an emission control device or prevent it from working. In some of the United States and in Canada, vehicle owners may be liable if their emission control device is removed or is prevented from working.
Page 227 The driving modes required to reach the ready condition consist of a minimum of 30 minutes of city and highway driving as described below. 20 minutes of driving in stop and go city-type traffic with at least four idle periods. 10 minutes of driving on an expressway or highway Before completing the above driving modes, the...
Page 228 Headlamp Bulb Your vehicle has retractable halogen headlamps. If you need to replace a headlamp, have it done by a Ford service technician. High-Mount Brakelamp Bulb To replace the bulb: 1. Remove the two side trim liftgate panels.
Page 229 High-mount brakelamp Rear Lamp Bulbs To replace a bulb: 1. Remove the attaching screw and the rear lens cover. Removing the attaching screw and lens...
Page 230 2. Partially remove the rear lens by pulling the lock tabs out of the slots. Pulling out the lock tabs 3. Turn the socket counterclockwise to remove it from the lens. 4. Remove the bulb from the socket by pushing it in and turning it counterclockwise.
Page 231 The rear lamps 5. Install the bulb by pushing it into the socket and turning it clockwise. 6. Install the socket by pushing it into its housing and turning it clockwise. The arrow on the socket must align with the arrow on the housing when installed.
Page 232: Cleaning Your Vehicle
Bulb Specifications Cleaning Your Vehicle Washing and Polishing Your Vehicle Wash the outside of your vehicle, including the underside, with a mild detergent. DO NOT: Wash your vehicle with hot water Wash your vehicle while it sits in direct sunlight Wash your vehicle while the body is hot Pollen, bird droppings and tree sap can damage the paint, especially in hot weather.
Page 233 Ford, however, believes that continual improvement in customer satisfaction is a high priority. For this reason, Ford has authorized its dealers to repair, at no charge to the owner, the surfaces of new vehicles damaged by...
Page 234 Cleaning the Exterior Lamps Do not use dry paper towel, chemical solvents or abrasive cleaners to clean the lamps, as these may cause scratches or crack the lamps. Cleaning the Engine A clean engine is more efficient because the engine is able to cool properly. A build up of grease and dirt acts as an insulator, keeping the engine warmer than normal.
Page 235 Rinse them with clear water. Cleaning the Instrument Panel Lenses To clean the lenses on your instrument panel, use Ford Glass Cleaner and a soft cloth. Never use paper towels or abrasive cleaners; they can scratch the lenses. Cleaning the Seats...
Page 236: Vehicle Storage
Cleaning the Safety Belts Clean the safety belts with any mild soap solution that is recommended for cleaning upholstery or carpets. Do not bleach or dye the belt webbing because this may weaken it. Vehicle Storage Maintenance Tips If you plan on storing your vehicle for an extended period of time (60 days or more), refer to the following maintenance recommendations to ensure your vehicle stays in good operating...
Page 237 Ford Gas Stabilizer should be added whenever actual or expected storage periods exceed 60 days. Follow the instructions on the label. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system.
Page 238 Cooling system Protect against freezing temperatures. Battery Check and recharge as necessary. Keep connections clean and covered with a light coat of grease. Brakes Make sure brakes and parking brake are fully released. Tires Maintain recommended air pressure. Miscellaneous Make sure all linkages, cables, levers and clevis pins under vehicle are covered with grease to prevent rust.
Page 239: Specifications
Capacities and Specifications Refill Capacities, Motorcraft Parts, and Lubricant Specifications Motorcraft Parts...
Page 240 Refill Capacities (Approximate)
Page 241 However, when refilling or adding is required, it should be with the proper lubricant or fluid meeting Ford technical specifications. See the Maintenance Schedule booklet for instructions on maintaining proper fluid levels.
Page 245: Reporting Safety Defects
National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 246: Customer Assistance
Customer Assistance Roadside Assistance Ford Motor Company has set up a 24-hour, seven-day-a-week hotline with trained operators who put you in touch with the help you need if you experience a problem with your vehicle. This complimentary service is provided to you throughout your warranty period of 3 years or 36,000 miles (60,000 km), whichever comes first.
Page 247 1-800-241-FORD (in Canada call 1-800-665-2006). If You Have a Service Problem Ford Motor Company has authorized Ford and Lincoln-Mercury dealerships that can service your vehicle for you. This chapter tells you how to get service or maintenance for your vehicle.
Page 248 If you are away from home when your vehicle needs to be serviced, or if you need more help than the dealer gave you, contact the Ford Customer Assistance Center to find an authorized dealership that may be able to help.
Page 249: The Dispute Settlement Board
Review? The Board reviews all warranty performance complaints on Ford, Mercury and Lincoln cars and Ford and Mercury light trucks under the new vehicle limited warranty that have not been resolved by either a dealer or Ford Motor Company, except those involving:...
Page 250 California and Wisconsin purchasers/lessees. How Does the Board Work? The Board consists of: three consumer representatives a Ford or Lincoln/Mercury dealer Consumer candidates for Board membership are recruited and trained by an independent consulting firm. Dealers are chosen because of...
Page 251 DSB’s independent administrator Your dealership and a Ford Motor Company representative are asked to submit statements at this time. To review your case properly, the Board needs...
Page 252 Board’s decision. The decisions of the Board are binding on the dealer and Ford, but not on consumers who may elect to pursue other remedies available to them under state and federal law. Decisions of the...
Page 253 Board at the following address: Ford of Canada Customer Assistance Ford Motor Company of Canada, Limited If you live in Canada and have any questions or concerns that the dealership cannot answer, contact the Customer Assistance Centre.
Page 254 Mediation/Arbitration Program (Canada Only) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 255 Use of leaded fuel in your vehicle without a proper conversion may damage the effectiveness of your emissions control system and may cause engine knocking or serious engine damage. Ford Motor Company is not responsible for any damage that is caused by use of improper fuel.
Page 256 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write to: If you are in other foreign countries, contact the nearest Ford dealership.
Page 257: Accessories
Accessories Ford Accessories for Your Vehicle Ford has many fine products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following, or products of equivalent quality: A wide selection of accessories is available through your local authorized dealer.
Page 258 Comfort and Convenience Protection and Appearance NOTE: When adding accessories, equipment, passengers, and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR, GAWR as shown on the Safety Compliance Certification Label).
Page 259 5 watts or less will not ordinarily affect your vehicle’s operation.) NOTE: Because we have no control over the installation, design, or manufacture of such systems, Ford cannot assume responsibility for any adverse effects or damage that may result if you use this equipment.
Page 271: Index
Index ABS warning light (see Anti-lock brake system) ..13 Accessory position on the ignition ..61 Additives, engine oil ..Air bag supplemental restraint system and child safety seats .
Page 272 Backing up ....Basic vehicle warranty ... Battery acid, treating emergencies ..175, 205 disconnecting .
Page 273 Bulbs, replacing halogen ....headlamps ....Canada, customer assistance ..Canada, warranty information .
Page 274 Cooling fan ....Crankcase emission filter ..Customer Assistance Center, Ford (U.S.) . . Customer Assistance Centre, Ford of Canada ... . 278 Index...
Page 275 Daytime running light system ..63 Defects, reporting ... . Dipstick automatic transaxle fluid ..engine oil ....power steering fluid .
Page 276 Engine check engine warning light ..15 does not start ... 128, 130 fuel injected engine, starting ..fuel pump shut-off switch ..preparing to start .
Page 277 Foglamps....57 Ford Customer Assistance Center ..Ford Motor Company of Canada ..Ford of Canada Customer Assistance Centre .
Page 278 Fuel pump shut-off switch engine does not start ..starting after a collision ..Gas cap (see Fuel cap) ..Gas mileage (see Fuel economy) .
Page 279 Hazard flashers ... . . Headlamps aiming ....checking alignment ..cleaning .
Page 280 Keys positions of the ignition ..61 stuck in lock position ..61 Lamps checking ....daytime running light system .
Page 281 Lug nuts standard ....tightening sequence ..Maintenance schedule and record (see separate Maintenance Schedule and Record booklet) ..Maintenance (see Servicing) .
Page 282 Oil viscosity ....On-board diagnostic (OBD II) system . . . Order forms, service information ..24 Overseas offices ... . . Parking brake operation .
Page 283 Restraints, safety (see Safety restraints) adult ....89, 98 child....head.
Page 284 Seat belts (see Safety restraints) ..98 Seats child safety seats ... cleaning upholstery ..folding rear seats .
Page 285 Storage compartments (continued) center console ... . . 80 map pockets ....80 Storing your vehicle ... Sunroof (moon roof).
Page 286 Transaxle control switch ..Trip odometer....19 Tune-up specifications (VECI)..Turn signal indicator lights .
Page 287 Warranty Information Booklet ..Washer fluid rear window reservoir ..reservoir ....windshield ....Weight limits (GAWR, GVWR) .
Page 288: Service Station Information
Service Station Information...

This manual is also suitable for:

Probe gt

Ford Probe Owner's Manual

Quick Links

Related Manuals for Ford Probe

Summary of Contents for Ford Probe

This manual is also suitable for:

Table of Contents