Page 1 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright 1997 Ford Motor Company...
Page 2: Introduction
If possible, you should avoid full use of the brakes for the first 1 600 km (1 000 miles). INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the...
Page 3 Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance Preparation package. Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’s Guide carefully.
Page 4: Instrumentation
Instrumentation Headlamp control (pg. 17) Instrument panel dimmer switch (pg. 18) Instrument cluster (pg. 6) FUEL 40 50 60 40• 20•km/h Turn signal and wiper/washer control (pg. 34) Speed control (pg. 28) • • • 0 0 0 0 • •140 THEFT •...
Page 5: Climate Control
Gearshift (includes overdrive button) (pg. 88) VOL-PUSH ON SEEK TUNE DISCS Auxiliary power point (pg. 19) Electronic sound system; refer to Audio Guide FM 1 FM 1 BASS TREB DOLBY 8 NR SCAN TAPE CD SIDE 1-2 COMP FLOOR PANEL COOL WARM Climate control...
Page 6: Warning Lights And Chimes
Instrumentation WARNING LIGHTS AND CHIMES Standard instrument cluster UNLEADED FUEL ONLY DOOR AJAR BRAKE CHECK ENGINE Optional instrument cluster FUEL DOOR AJAR BRAKE Low fuel Illuminates when the fuel level is low. The lamp will also illuminate when the ignition key is turned to ON and the engine is off.
Page 7 Instrumentation the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II system also assists the service technician in properly servicing your vehicle. The Check Engine indicator light illuminates when the ignition is first turned to the ON position to...
Page 8 Instrumentation with good quality fuel and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Check Engine light should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required.
Page 9 Instrumentation Safety belt Momentarily illuminates when the ignition is turned ON to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Brake system warning BRAKE Momentarily illuminates when the ignition is turned on and the engine is off.
Page 10 Instrumentation High beams Illuminates when the high beam headlamps are turned on. Anti-theft system (if equipped) Refer to Perimeter alarm system in the Controls and features chapter. Charging system Momentarily illuminates when the ignition is turned ON and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service.
Page 11 Instrumentation oil pressure gauge in this chapter for more information. Four wheel drive low (if equipped) Illuminates when four-wheel drive RANGE low is selected. Four wheel drive indicator (if equipped) Illuminates when 4x4 range is selected. Check air suspension (if equipped) CHECK Illuminates briefly when the...
Page 12 Instrumentation Fuel reset FUEL Illuminates when the ignition key is turned to the ON position and RESET the fuel pump shut-off switch has been triggered. For more information, refer to Fuel pump shut-off switch in the Roadside emergencies chapter. Safety belt warning chime Chimes to remind you to fasten your safety belts.
Page 13: Fuel Gauge
GAUGES Standard instrument cluster gauges UNLEADED FUEL ONLY DOOR AJAR BRAKE CHECK ENGINE Optional instrument cluster gauges FUEL DOOR AJAR BRAKE Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion.
Page 14 Instrumentation When refueling the vehicle from empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel. Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of the engine coolant.
Page 15 is not at its proper level or mixture, the gauge indication will not be accurate. Odometer Registers the total kilometers (miles) of the vehicle. Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. Tachometer Indicates the engine speed in revolutions per minute.
Page 16 Instrumentation Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’s electrical system checked as soon as possible. Engine oil pressure gauge This shows the engine oil pressure in the system.
Page 17: Controls And Features
HEADLAMP CONTROL Rotate the headlamp control to the desired position: — OFF. — Parking lamps on. — Headlamps on. Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamps are in the position.
Page 18 Controls and features The Daytime Running Light (DRL) system will not illuminate the tail lamps and parking lamps. Turn on your headlamps at dusk. Failure to do so may result in a collision. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel.
Page 19 A small LED illuminates next to the autolamp control to indicate that the headlamps have been turned on by the autolamps. Foglamps are not controlled by the autolamps. In order to turn on the foglamps, you must turn the lamp switch to the position and pull for fog.
Page 20 Controls and features CLIMATE CONTROL SYSTEM Heater only system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. On heater-only systems, the air cannot be cooled below the outside temperature.
Page 21 Controls and features PANEL & FLOOR-Distributes outside air through the instrument panel registers and the floor ducts. FLOOR-Allows for maximum heating. Distributes outside air through the floor ducts. FLOOR & DEF-Distributes outside air through the floor ducts and the windshield defroster ducts.
Page 22 Controls and features Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood). When placing objects on top of your instrument panel, be careful to not place them over the defroster outlets. These objects can block airflow and reduce your ability to see through your windshield.
Page 23 Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor will operate in all modes except PANEL and FLOOR. However, the air conditioning will only function if the outside temperature is about 10°C (50°F) or above.
Page 24 Controls and features vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers.
Page 25 Controls and features hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers. FLOOR-Allows for maximum heating by distributing outside air through the floor ducts. However, the air will not be cooled below the outside temperature because the air...
Page 26 Controls and features Operating tips In humid weather, select DEF before driving. This will prevent your windshield from fogging. After a few minutes, select any desired position. To prevent humidity buildup inside the vehicle, don’t drive with the climate control system in the OFF position.
Page 27 reduce your ability to see through your windshield. Also, avoid placing small objects on top of your instrument panel. These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system. POSITIONS OF THE IGNITION 1.
Page 28 Controls and features SPEED CONTROL (IF EQUIPPED) To turn speed control on Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
Page 29 To set a speed Press SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Page 30 Controls and features To set a higher set speed Press and hold SET ACC/SET ACCEL. Release the control when the desired vehicle speed is reached or Press and release SET ACC/SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or Accelerate with your accelerator pedal, then press and release...
Page 31 Depress the brake pedal. When the desired vehicle speed is reached, press SET ACC/SET ACCEL. To disengage speed control Depress the brake pedal or Depress the clutch pedal (if equipped) Disengaging the speed control will not erase the previously programmed set speed. Controls and features...
Page 32 Controls and features Pressing OFF will erase the previously programmed set speed. To return to a previously set speed Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Page 33 Pull the steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving.
Page 34 Controls and features WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.
Page 35 Controls and features 4. Within two seconds of pressing the washer control, put the key in the ignition. 5. Continue to press the washer control until a tone is heard, and releas the washer control while the tone is sounding. A confirmation sequence of tones will sound.
Page 36 Controls and features The overdrive function allows automatic upshifts to second, third and forth gear. Deactivating overdrive Press the transmission control at OVERDRIVE the end of the gearshift lever. The transmission control indicator light TCIL (OFF) will illuminate on the end of the gearshift lever The transmission will operate in OVERDRIVE...
Page 37 POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. Press the top portion of the rocker switch to close. Press the bottom portion of the rocker switch to open. One touch down Press AUTO and release quickly. The window will open fully.
Page 38 Controls and features Accessory delay With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until either door is opened. POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all doors and L to lock all doors.
Page 39 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. TAILGATE LOCK (IF EQUIPPED) Your vehicle is equipped with a tailgate lock designed to prevent theft of the tailgate. Insert ignition key and turn to the right to engage lock.
Page 40 Controls and features TAILGATE REMOVAL Your tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry the spring clip (on each connector) past the head of the support screw. Disconnect cable. 3.
Page 41 Press the remote entry lock control Open a door and press the power door lock control to lock the doors If a door is open, the system is prearmed and is waiting for the door to close. The theft indicator in the instrument panel will be lit continuously when the system is prearmed.
Page 42 Controls and features Unlock the doors by using your remote entry transmitter. Unlock the doors with a key. Turn the key full travel (toward the front of the vehicle) to make sure the alarm disarms. Turn ignition to ACC or ON. Press the panic control on the remote entry transmitter.
Page 43 Controls and features Unlocking the doors Press this control to unlock the driver door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within five seconds.
Page 44 Controls and features and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Autolock This feature automatically locks all doors when:...
Page 45 2. Press the power door unlock control three times. 3. Turn the ignition key from ON to OFF. 4. Press the power door unlock control three times. 5. Turn the ignition back to ON. The horn will chirp. 6. Press the unlock control, then press the lock control.
Page 46 Controls and features the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together.
Page 47 four). When completed, switch the ignition to OFF. All transmitters must be reprogrammed at the same time. Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the START or ACC position.
Page 48: Seating And Safety Restraints
Seating and safety restraints SEATING Full bench seat (if equipped) Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place. Push down the release lever to quickly fold the seatback forward. 60/40 split bench seat (if equipped) Lift the release bar to move the...
Page 49 Captain’s chair (if equipped) Lift the release bar to move the seat forward or rearward. Make sure that the seat is relatched into place. Pull the seatback handle up to recline the seat. Push the release lever down to quickly fold the seatback forward.
Page 50 Seating and safety restraints Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Using the manual lumbar support Turn the lumbar support control...
Page 51 60/40 Split Rear Seat (if equipped) When folded down, the rear seats provide a “load floor” for additional storage space. To fold down the rear seats: Pull the straps to lower the seat cushions. Store the center safety belt in the opening on the seat back.
Page 52 Seating and safety restraints To prevent the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Page 53 Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm.
Page 54 Seating and safety restraints combination lap and shoulder belts. The front and rear seat passenger outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Page 55 Anytime a child safety seat is installed in the vehicle. Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter. How to use the automatic locking mode Buckle the combination lap and shoulder belt. Grasp the shoulder portion and pull downward until the entire belt is extracted.
Page 56 Seating and safety restraints How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and...
Page 57 Seating and safety restraints and as low as possible around your hips. Do not wear the lap belt around your waist. Insert the tongue into the correct buckle. To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
Page 58 Seating and safety restraints belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Do not use extensions to change the fit of the shoulder belt across the torso.
Page 59 (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor...
Page 60 Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) 50 60 FUEL 0 0 0 0 0 0 DOOR AJAR BRAKE km/h P R N PULL PANEL Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to: work with the safety belt to protect the driver and right front passenger...
Page 61 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide.
Page 62 Seating and safety restraints Air bag can kill or injure a child in a child seat. Child seats should never be placed in the front seats, unless passenger air bag switch is turned off. See Passenger air bag deactivate switch. How does the air bag supplemental restraint system work?
Page 63 Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is inflated, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 64 Seating and safety restraints Instrumentation chapter. Routine maintenance of the air bag is not required. A difficulty with the system is indicated by one or more of the following: The readiness light will either flash or stay lit. The readiness light will not illuminate immediately after ignition is turned on.
Page 65 Passenger air bag deactivate switch Your vehicle has a passenger air bag deactivate switch. This switch MUST be used to activate or deactivate the passenger air bag whenever a child seat is used in the right front or center front passenger seat position.
Page 66 OFF position and the ignition switch is in ON, have the passenger air bag switch serviced at your Ford or Lincoln-Mercury dealer immediately. In order to avoid inadvertent deployment of the passenger air bag, always...
Page 67 ON position and the ignition switch is in ON, have the passenger air bag switch serviced at your Ford or Lincoln-Mercury dealer immediately. Keep the passenger air bag turned on unless there is a child seat installed in the front seat.
Page 68 Seating and safety restraints SAFETY RESTRAINTS FOR CHILDREN Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for...
Page 69 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards.
Page 70 Seating and safety restraints A belt-positioning booster should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion.
Page 71 Put the safety belt in the automatic locking mode. Refer to Automatic locking mode. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 72 Seating and safety restraints Air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together.
Page 73 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 74 The anchor bracket must be installed using the instructions provided with the kit. Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer.
Page 75 Carefully follow the instructions provided with the kit. If you have a SuperCab Ford recommends you attach tether safety seats in the rear seating position (if possible) with the...
Page 76: Starting
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the spark ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 77 Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle...
Page 78 Starting Make sure the parking brake is set. Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: Make sure the parking brake is set. Push the clutch pedal to the floor.
Page 79 3. Turn the key to 4 (ON) without turning the key to 5 (START). FUEL DOOR AJAR BRAKE Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the light ( illuminate.
Page 80 Starting STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the engine does not start within five seconds, wait ten seconds and try again.
Page 81 quickly. They are strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below. For best results, plug the heater in at least three hours before starting the vehicle. Using the heater for longer than three hours will not harm the engine, so the heater can be plugged in the night before starting the vehicle.
Page 82 Starting the sound of the exhaust system changes the vehicle has been damaged in a collision Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch).
Page 83: Driving
Driving BRAKES Your brakes are self-adjusting. Refer to the “Service Guide” for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 84 Driving shudder while braking, felt mainly in the steering wheel, the vehicle most likely needs service. The ABS operates by detecting the onset of wheel lock up during brake applications and compensating for this tendency. The front wheels are prevented from locking even when the brakes are firmly applied.
Page 85 there is sufficient space, will enable you to avoid obstacles and bring the vehicle to a controlled stop. We recommend that you familiarize yourself with this braking technique. However, avoid taking any unnecessary risks. Parking brake Apply the parking brake whenever the vehicle is parked.
Page 86 Driving The parking brake is not designed to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will be adversely affected.
Page 87 normal driving and should not be noticeable to the driver. To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire. AIR SUSPENSION SYSTEM (IF EQUIPPED) The air suspension system is designed to improve ride, handling and general vehicle performance for static, on and off-road driving conditions.
Page 88 Driving The air suspension shut-off switch is located behind an access panel underneath the passenger side instrument panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver.
Page 89 is possible that a fuse has blown and the vehicle’s brakelamps may not be operating properly. Refer to Fuses and relays in the Roadside emergencies chapter. Do not drive your vehicle until you verify that the brakelamps are working. If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears in a steady pattern.
Page 90 Driving Hold the brake pedal down while you move the gearshift lever from position to position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) Always come to a complete stop before shifting into P (Park).
Page 91 control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) (the word OFF) on the end of the gearshift lever will illuminate. Drive – Not shown on the display. Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the position.
Page 92 Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive).
Page 93 1. Put gearshift in N (Neutral). 2. Hold down brake pedal. 3. Depress clutch pedal. Driving...
Page 94 Driving 4. Turn ignition key to Start to start the engine and let it idle for a few seconds. 5. Release the brake pedal. 6. Release clutch slowly while pressing down slowly on the accelerator pedal. Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill while...
Page 95 Upshifts when accelerating (recommended for best fuel 2 - 3 3 - 4 (Overdrive) Upshifts when cruising (recommended for best fuel economy) Shift from: 1 - 2 2 - 3 3 - 4 (Overdrive) Maximum downshift speeds Shift from: (Overdrive) - 4 - 3 3 - 2 2 - 1...
Page 96 Driving Parking your vehicle 1. Apply brake and shift into N (Neutral). 2. Set parking brake. 3. Shift into 1 (First).
Page 97 4. Turn ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse).
Page 98 Driving Removing key from ignition Turn the ignition key until it stops. Push the release lever forward and rotate the key towards you until it stops. Release the lever and remove the key from the ignition. FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) When Four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer...
Page 99 Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns or abrupt maneuvers in these vehicles. 4WD operation is not recommended on dry pavement.
Page 100 Driving 4H (4WD High) – Power to front and rear axles. N (Neutral) – No power to either axle. 4L (4WD Low)– Power to front and rear axles at reduced speed. Shifting from 2H (2WD High) to 4H (4WD High) Move the transfer case lever to 4H (4WD High) at a stop or any forward speed up to 88 km/h (55...
Page 101 2. Place the gearshift lever in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 3. Pull the transfer case shift lever through N (Neutral) directly to 4H (4WD High) or 4L (4WD Low). Shifting from N (Neutral) to 4H (4WD High) or 4L (4WD Low) With the transfer case in N (Neutral) the vehicle is free to...
Page 102 Driving transmission and puts the vehicle in neutral regardless of transmission gearshift lever position. The vehicle can move forward or backwards. Make sure the parking brake is applied and the vehicle is never left unattended with the transfer case in neutral. This position should only be used when towing the vehicle.
Page 103 Shifting from 2H (2WD high) to 4H (4WD High) Move the 4WD control to the 4H at a stop or up to 88 km/h (55 mph). At temperatures below 0°C (32°F), shifts from 2H to 4H should not be performed above 72 km/h (45 mph).
Page 104 Driving 4. Move the 4WD control to the 4H or 4L position. Driving off-road with 4WD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road.
Page 105 If your vehicle gets stuck If the vehicle is stuck, shift the transmission in a steady motion between forward and reverse gears. Allow the transmission to engage, then press lightly on the accelerator. DO NOT rock the vehicle for more than a few minutes.
Page 106 Driving Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. After driving through mud, clean off residue stuck to rotating driveshafts and tires.
Page 107 Driving hill before driving over the crest. When climbing a steep hill, start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started. This reduces strain on the engine and the possibility of stalling.
Page 108 Driving Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. When braking, apply the brakes as you normally would. In order to allow the anti-lock brake system (ABS) to operate properly, keep steady pressure on the brake pedal.
Page 109 Driving vehicle and is listed on the Safety Compliance Label on the driver’s door pillar. GAWR (Gross Axle Weight Rating): Carrying capacity for each axle system. The GAWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver’s door pillar.
Page 110 Driving trailer must fall within that ranges from zero to the maximum trailer weight rating. Remember to figure in the tongue load of your loaded trailer when figuring the total weight. Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label.
Page 111 Driving on the following charts. This is the maximum trailer weight your vehicle can tow and must fall below the maximum shown under maximum trailer weight on the chart. DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown.
Page 112 Driving TOWING A TRAILER Your vehicle may tow a class I, II or III trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and rear axle ratio on the following charts.
Page 113 Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury. Trailer towing tables F-150 4x2 with automatic transmission Engine Rear axle ratio Maximum 4.2L 3.08 4.2L 3.55 4.6L 3.08...
Page 114 Driving F-150 4x2 manual transmission Engine Rear axle ratio 4.2L 3.08 4.2L 3.55 4.6L 3.08 4.6L 3.55 4.2L 3.08 4.2L 3.55 4.6L 3.08 4.6L 3.55 F-150 4x4 automatic transmission Engine Rear axle ratio 4.2L 3.08 4.2L 3.55 4.6L 3.08 4.6L 3.55 5.4L 3.08...
Page 115 Engine Rear axle ratio 4.6L 3.55 5.4L 3.08 5.4L 3.55 F-150 4x4 manual transmission Trailer towing table (F-150 4x4 manual transmission) Engine Rear axle ratio 4.2L 3.08 4.2L 3.55 4.6L 3.08 4.6L 3.55 4.6L 3.08 4.6L 3.55 F-250 4x2 automatic transmission Engine Rear axle...
Page 116 Driving Engine Rear axle ratio 4.6L 3.73 5.4L 3.31 5.4L 3.73 4.6L 3.31 4.6L 3.73 5.4L 3.31 5.4L 3.73 F-250 4x2 manual transmission Engine Rear axle ratio 4.6L 3.31 4.6L 3.73 4.6L 3.31 4.6L 3.73 Maximum Maximum GCWR-kg (lbs.) weight-kg 5 436 (12 000) 3 311 (7 300) 5 436 (12 000) 3 265 (7 200) 6 115 (13 500) 3 946 (8 600)
Page 117 F-250 4x4 automatic transmission Engine Rear axle ratio 4.6L 3.31 4.6L 3.73 5.4L 3.31 5.4L 3.73 4.6L 3.31 4.6L 3.73 5.4L 3.31 5.4L 3.73 F-250 4x4 manual transmission Engine Rear axle ratio 4.6L 3.31 4.6L 3.73 Maximum Maximum GCWR-kg trailer (lbs.) weight-kg (lbs.)
Page 118 Driving Engine Rear axle ratio 4.6L 3.31 4.6L 3.73 Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance.
Page 119 3. Measure the height of a reference point on the front and rear bumpers at the center of the vehicle. 4. Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within 0–13 mm (0.5 in) of the reference point.
Page 120 Driving must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. Trailer lamps Trailer lamps are required on most towed vehicles.
Page 121 Use D (Drive) or a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling. Anticipate stops and brake gradually. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals.
Page 122 Driving (automatic transmissions) or 1 (First) (manual transmissions) and increase idle speed. This aids engine cooling and air conditioner efficiency. Vehicles with trailers should not be parked on a grade. If you must park on a grade, place wheel chocks under the trailer’s wheels.
Page 123 Driving Recreational towing (all wheels on the ground) Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication.
Page 124 Driving 3. Lockout the center disconnect by capping off one of the front axle vacuum motor lines. See your Ford dealer for assistance. 4. Vehicle speed should not exceed 88 km/h (55 mph) and there are no mileage restrictions. 4WD – Electronic shift transfer case 1.
Page 125 F-150/F–250 4WD Regular Cab long wheelbase 4.6L or 5.4L engine Heavy duty service package Super engine cooling Heavy duty front suspension package Automatic transmission with auxiliary automatic transmission fluid cooling All-terrain tires Do not install a snowplow and plow with your vehicle until it has been driven at least 800 km (500 miles).
Page 126 Driving must not exceed the front accessory reserve capacity. The total weight of the snowplow and aftermarket equipment must not exceed the Total Accessory Reserve Capacity. The weight of the installed snowplow and aftermarket equipment must not load the vehicle beyond the GAWR (front/rear) and GVWR listed on the Safety Compliance Certification Label.
Page 127 maintain the engine oil and transmission fluid change intervals. Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label. Removing snowplow Read the following instructions before removing a snowplow: After removing a snowplow from the vehicle, ensure the vehicle’s front toe alignment and front ride height are within specification (reset if required).
Page 128 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Engine temperature while plowing When driving with a plow, your engine may run at a higher...
Page 129 either full left or full right to provide maximum airflow to the radiator. If you are driving less than 24 km (15 miles) at speeds up to 64 km/h (40 mph) in cold weather, you will not need to worry about blade position to provide maximum airflow.
Page 130 Driving FUEL CONSUMPTION Fuel economy can be improved by avoiding: lack of regular, scheduled maintenance excessive speed rapid acceleration extended idle...
Page 131: Hazard Lights Control
HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. The hazard lights control is located on top of the steering column. Depress hazard lights control to activate all hazard flashers simultaneously.
Page 132 Roadside emergencies 5. Make a further check for leaks in the fuel system. The fuel pump shut-off switch is located in the passenger’s foot well, behind the kick panel. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown.
Page 133: Standard Fuse Amperage Rating And Color
Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color Fuse rating 5 amp 7.5 amp 10 amp 15 amp...
Page 134: Fuse Panel Description
Roadside emergencies The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description Flasher Relay Instrument Cluster Cigar Lighter Park Lamp Relay, Headlamp Relay, Autolamp Module Remote Anti-Theft Personality (RAP) Module, Power Mirror Switch...
Page 135 Fuse/Relay Location Roadside emergencies Fuse Amp Rating — — — Description Digital Transmission Range (DTR) Sensor (A/T), Backup Lamp Switch (M/T), Daytime Running Lights (DRL) Module, Speed Control Servo/Amplifier Assembly, Heater-A/C Control Assembly, Blend Door Actuator Shift Lock Actuator, Generic Electronic Module (GEM), Rear Air Suspension (RAS) Module...
Page 136 Roadside emergencies Fuse/Relay Location Fuse Amp Rating — Description Battery Saver Relay, Interior Lamp Relay Generic Electronic Module (GEM) Instrument Cluster (W/O DRL), Daytime Running Lamps (DRL) Module, Hi-Beam Headlamps (Power supplied through Multi-Function Switch) Not Used Park Lamp Relay, Trailer Electronic Brake Controller, Main Light Switch, Trailer...
Page 137 Fuse/Relay Location Roadside emergencies Fuse Amp Rating Description Clutch Pedal Position (CPP) Switch (W/O RAP), Starter Interrupt Relay (W/RAP) Air Bag Diagnostic Monitor, Passive De-Activation (PAD) Module Trailer tow Battery Charge Relay, 4X4 Hub Solenoid, 4X2 Hub Solenoid, Flasher Relay, Shift on the Fly Relay Blower Relay 4 Wheel Anti-Lock...
Page 138 Roadside emergencies Fuse/Relay Location Relay 1 Relay 2 Not Used Relay 4 Relay 5 Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
Page 139: Power Distribution Box
The high-current fuses are coded as follows. Fuse/Relay Location Roadside emergencies Fuse Amp Rating 20A * 10A* 15A* Description Trailer Tow Running Lamp Relay, Trailer Tow Backup Lamp Relay Air Bag Diagnostic Monitor All Unlock Relay, All Lock Relay, Driver Unlock Relay, LH Power Door Lock Switch, RH Power...
Page 140 Roadside emergencies Fuse/Relay Location Fuse Amp Rating 15A* 20A* 15A* 15A* 30A* 15A* 25A* — — — 60A**/20A** 50A** 40A** 30A** 30A** 20A** Description Rear Air Suspension (RAS) Horn Relay Radio, Premium Sound Amplifier, CD Changer Main Light Switch, Park Lamp Relay Main Light Switch, Headlamp Relay, Multi-Function Switch...
Page 141 Fuse/Relay Location *Mini fuses **Maxi fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Spare tire information Your vehicle is equipped with a spare tire that may be used as a...
Page 142: Removing The Spare Tire
Roadside emergencies If your vehicle is equipped with 4WD or AWD, a spare tire of a different size than the road tires should not be used. Such a tire could result in damage to driveline components and make the vehicle difficult to control. Location of the spare tire and tools The spare tire and tools for your...
Page 143 2. Slide the wheel under the vehicle and install the retainer through the wheel center. 3. Turn the jack handle clockwise until the tire is raised to its original position underneath the vehicle. The jack handle ratchets when the tire is raised to the stowed position.
Page 144 Roadside emergencies 3. Block the diagonally opposite wheel. 4. Obtain the spare tire and jack from their storage locations. 5. Use the tip of the lug wrench to remove any wheel trim. 6. Loosen each wheel lug nuts one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.
Page 145 Roadside emergencies Front (4x2) Front (4x4) Rear...
Page 146 Roadside emergencies Never use the front or rear differential as a jacking point. 9. Remove the lug nuts with the lug wrench. 10. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub.
Page 147 JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which burns skin, eyes, and clothing.
Page 148 Roadside emergencies 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off. Connecting the jumper cables 1.
Page 149 Jump starting 1. Start the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the vehicle with the discharged battery. 3. Once the engine has been started, run both vehicles for a further three minutes before disconnecting the leads.
Page 150 On 4x4 vehicles, it is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with slingbelt equipment. Ford Motor Company has not developed or approved a slingbelt towing procedure.
Page 151 Roadside emergencies When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for proper hook-up and towing procedures for your vehicle.
Page 152: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a “Service Guide” which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Page 153 Do not work on a vehicle with the engine running in an enclosed space, unless you are sure you have enough ventilation. Keep all lit cigarettes, open flames and other lit material away from the battery and all fuel related parts. If you disconnect the battery, the engine must “relearn”...
Page 154 Maintenance and care Working with the engine on Automatic transmission: 1. Set the parking brake fully and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. Do not start your engine with the air cleaner removed and do not remove it while the engine is running.
Page 155 IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.2L engine 1. Battery 2. Engine oil filler 3. Engine oil dipstick 4. Clutch fluid reservoir (if equipped) 5. Brake fluid reservoir 6. Engine coolant recovery reservoir 7. Air filter assembly 8. Power steering fluid reservoir 9.
Page 156 Maintenance and care 4.6L/5.4L engines 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler 4. Engine oil dipstick 5. Clutch fluid reservoir (if equipped) 6. Power steering fluid reservoir 7. Brake fluid reservoir 8. Air filter assembly 9. Engine coolant recovery reservoir 10.
Page 157 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4.
Page 158 Maintenance and care If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician.
Page 159 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL.
Page 160 3. Recheck the oil level. Make sure the oil level is not above the MAX mark on the dipstick. Engine oil recommendations Look for this certification mark. Ford oil specification is WSS-M2C153-G. Use SAE 5W-30 motor oil certified for gasoline engines by the American Petroleum Institute.
Page 161 Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced.
Page 162 3. If necessary, add brake fluid until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter.
Page 163 If the fluid level drops, maintain the fluid level at the step in the reservoir. Use only a DOT 3 brake fluid designed to meet Ford specifications. Refer to Capacities and specifications. 1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir.
Page 164 Maintenance and care WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
Page 165 Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding engine coolant Do not put engine coolant in the container for the windshield washer fluid. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield.
Page 166 ESE-M97B44–A. Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for four years or 80,000 km (50,000 miles). Do not use alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze.
Page 167 Maintenance and care coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and use of such coolant may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner.
Page 168 Maintenance and care Leave a 50/50 mixture of engine coolant and water in your vehicle year-round in non-extreme climates. What you should know about fail-safe cooling (if equipped) If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred.
Page 169 As the engine temperature cools, the engine may be re-started. Take your vehicle to a service facility as soon as possible to minimize engine damage. When fail-safe mode is activated Pull off the road as soon as possible. Immediately turn the engine off to prevent severe engine damage.
Page 170 Maintenance and care 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and...
Page 171 concerns and/or possible damage. Do not drive the vehicle if the fluid level is below the hole at the bottom of the blade type dipstick (4R70W transmission) or below the COLD area on the bullet type dipstick (E4OD transmission) and outside temperatures are above 10°C (50°F) (see figure to the right).
Page 172 Maintenance and care The transmission fluid should be in DON'T ADD IF IN CROSSHATCHED AREA • CHECK WHEN HOT IDLING IN PARK this range if at room temperature (10°C-35°C [50°F-95°F]) (see figure to the right). COLD DO NOT ADD If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the...
Page 173 Maintenance and care 7. If necessary, add fluid in .25L (1/2 pint) increments through the filler tube until the level is correct. 8. If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible...
Page 174 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
Page 175 Maintenance and care 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. DRIVELINE UNIVERSAL JOINT...
Page 176 Maintenance and care the electrolyte in each cell up to the “level” indicator. Do not overfill the battery cells. If the electrolyte level in the battery is low, you can add plain tap water to the battery, as long as you do not use hard water (water with a high alkali content).
Page 177 its idle conditions before your vehicle will drive properly. To begin this process: 1. Put the gearshift in P (Park) (automatic transmissions) or the neutral position (manual transmissions), turn off all accessories and start the vehicle. 2. Let the engine idle for at least one minute.
Page 178 Maintenance and care treatments used by commercial car washes reduce the effectiveness of wiper blades. Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent.
Page 179 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear The treadwear grade is a...
Page 180 Maintenance and care tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. Traction A B C The traction grades, from highest to lowest are A, B, and C, and they represent the tire’s ability to stop on wet pavement as measured...
Page 181 Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.
Page 182 Maintenance and care Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the “Service Guide.” If you notice that the tires wear unevenly, have them checked.
Page 183 Replacing the tires Replace the tires when the wear band is visible through the tire treads. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer.
Page 184 Maintenance and care Follow these guidelines when using snow tires and chains: Use only SAE Class S chains. Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. Drive cautiously. If you hear the chains rub or bang against your vehicle, stop and re-tighten the chains.
Page 185 If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. The fuel system may be under pressure. If the fuel cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the cap.
Page 186 Maintenance and care promptly remove contaminated clothing and wash skin thoroughly with soap and water. If fuel is splashed in the eyes, remove contact lenses, flush with water for 15 minutes and seek medical attention. Be particularly careful if you are taking “Antabuse”...
Page 187 If the condition persists, see your dealer or a qualified service technician. The American Automobile Manufacturers Association (AAMA) issued a gasoline specification to provide information on high quality fuels that optimize the performance of your vehicle.
Page 188 Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE.
Page 189 Guide” are required because they are considered essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting...
Page 190 Maintenance and care parts in performance and durability. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Watch for fluid leaks, strange odors, smoke, loss of oil pressure, the charging system warning light,...
Page 191 identifies engine displacement and gives some tune up specifications. Please consult your “Warranty Guide” for complete emission warranty information. Readiness for inspection/maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostic (OBD-II) system.
Page 192 Maintenance and care complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. EXTERIOR BULBS Replacing exterior bulbs Check the operation of the following lamps frequently: headlamps foglamps (if equipped)
Page 193 Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Page 194 Maintenance and care 8. Insert the glass end of the new bulb into the headlamp assembly socket. When the grooves in the plastic base are aligned, push the bulb into the socket until the plastic base contacts the rear of the socket.
Page 195 Maintenance and care Replacing parking lamp/turn signal bulbs 1. Remove screw from the top of lamp assembly. 2. Disengage lamp assembly (it has a snap fit). 3. Remove the electrical connector from the bulb by grasping the wire and pulling it rearward. 4.
Page 196 Maintenance and care 9. Align top and bottom ribs of parking lamp assembly with corresponding slots on front of vehicle. 10. Push gently until parking lamp assembly seats (you will hear a snap). 11. Replace screw removed in step Replacing foglamp bulbs 1.
Page 197 Replacing license plate lamp bulbs The license plate bulbs are located under and behind the rear bumper. To change the license plate lamp bulbs: 1. Reach under and behind the rear bumper to locate the bulb connector. 2. Twist the connector counterclockwise ⁄...
Page 198 CLEANING AND CARING FOR YOUR VEHICLE Refer to the “Customer Assistance Guide” for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap.
Page 199 Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up , paint repair foil or aerosol paint spray from the Ford accessory line. Observe the application instructions on the products. Remove particles such as bird...
Page 200 Maintenance and care Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage.
Page 201 Maintenance and care Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle.
Page 202 Maintenance and care Remove fresh spots immediately. Follow the directions that come with the cleaner. Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing.
Page 203 will damage the leather surface Spray a small amount of the leather cleaner on the pad and rub the area to be cleaned with the pad using a circular motion. Only clean 1/4 of the area at a time. For heavily soiled areas, spray the cleaner directly onto the leather (two squirts should be adequate) and rub with the...
Page 204 Maintenance and care 04011–01276) are available through your local 3M distributor. Call 1–800–742–9649 for the nearest distributor in your area. PART NUMBER (Obtain Locally) (Obtain Locally) PART NAME Tanners Preserve Leather Cleaner 3M Type T Clean and Finish Scrubbing Pads...
Page 205: Capacities And Specifications
Fuel filter Oil filter PCV valve Battery (manual transmission) Battery (automatic transmission) Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Ford Part Fluid Name Motorcraft SAE 75W90 Front axle Front Axle Lubricant Motorcraft 75W140...
Page 206 Capacities and specifications Ford Part Fluid Name Motorcraft 75W140 Rear axle Synthetic Rear Axle Lubricant Ford High Performance Brake fluid DOT 3 Brake Fluid Ford Premium Engine Cooling coolant System Fluid Engine oil Motorcraft (includes 5W30 Super filter Premium change)
Page 207 Add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546-A, Ford specification EST-M2C118–A, for complete fill of 8.8 inch and 9.75 inch axles. Add 236 ml (8 oz.) of additive Friction Modifier C8AZ-19B546-A, Ford Specification EST-M2C118-A, for complete fill of 10.25 inch...
Page 208 Capacities and specifications Fill to 6 mm (3/8 inch) below bottom of filler hole. In-vehicle refill: approximately 3.1L (6.5 pints). LUBRICANT SPECIFICATIONS Ford part Fluid name or equivalent 75W90 Gear Front axle Lube Motorcraft SAE 75W140 High Rear axle Performance...
Page 209 (4R70W) Ultra-clear Windshield windshield washer fluid washer concentrate You must add 4–ounces of additive friction modifier C8AZ-19B546–A, Ford specification EST-M2C118–A to the rear axle whenever the axle has been serviced. Capacities and specifications Ford part number XG-1-C XT-2-BDX or XT-2-BDX-QDX...
Page 210 Capacities and specifications ENGINE DATA Engine 4.2L engine Cubic inches Horsepower 205 @ 4440 rpm 220 @ 4500 rpm 235 @ 4250 rpm 255 lb. ft. @ Torque 3000 rpm Required fuel 87 octane grade Firing order 1-4-2-5-3-6 1.3-1.4 mm Spark plug gap (0.052-.056 inch)
Page 211 Dimension Regular Cab 4x2 1 846 mm (72.7 in) (3) Overall (SWB) 1838 height mm (72.4 in) (LWB) 3 022 mm (119.9 in) (4)Wheel (SWB)3 505 base mm (138.5 in) (LWB) 1 661 mm (5)Track (65.4 in)/1 front/rear 661 mm (65.4 in) Flareside Dimension...
Page 212 Capacities and specifications...
Page 213 IDENTIFYING YOUR VEHICLE Vehicle identification plate The vehicle identification plate is located on the front panel of the engine compartment. This plate bears technical information on your vehicle and identifies various components. Capacities and specifications FORD...
Page 214 Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is XXXXXXXXXXXXXXXXX located on the driver side instrument panel. Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if so equipped).
Page 215: Reporting Safety Defects
National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a...
Page 216: Index
Index Air bag supplemental restraint system ...60 and child safety seats ...61 description ...60 disposal ...64 indicator light ...63 passenger air bag ...62,65,66 Air conditioning manual heating and air conditioning system ...22,23,26 Air suspension description ...87 warning light ...11 Ambulance packages ...3 Anti-lock brake system (ABS) description ...84 Anti-theft system ...40...
Page 217 Fuse panels instrument panel ...133 power distribution box ...138 Fuses ...132,133 Gauges, Mechanical ...13 engine coolant temperature gauge ...14 Hazard flashers ...131 Headlamps autolamp system ...18 flashing ...35 high beam ...35 turning on and off ...17 Heating ...20 High beams indicator light ...10 Hood release lever ...154...
Page 218 Index warning light and chime ...12,58 Safety seats for children attaching with tether straps ...74 automatic locking mode (retractor) ...71 tether anchorage hardware ...74 Seats ...48 adjusting the seat, manual ...49 adjusting the seat, power ...49 bench (60-40 split) ...48,51 bench seat ...48 lumbar support ...50 Servicing your vehicle ...152...
Page 219: Filling Station Information
(4 x 4) Unleaded fuel only - 87 octane 92.7L (24.5 gallons) 94.6L (25 gallons) Use Motorcraft 5W30 Super Premium Motor Oil, Ford Specification WSS-M2C153-G Refer to Tire Pressure Decal on passenger’s door panel Pull handle under the left side of the instrument panel 5.7L (6.0 quarts)

This manual is also suitable for:

F-150 F-150 1997

Ford 1998 F-150 Owner's Manual

Quick Links

Related Manuals for Ford 1998 F-150

Summary of Contents for Ford 1998 F-150

This manual is also suitable for:

Table of Contents