1. Manuals
  2. Brands
  3. Ford Manuals
  4. Automobile
  5. 1999 F-350
  6. Owner's manual

Ford 1999 F-350 Owner's Manual

Ford motor company 1999 ford f-350 owner's guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Before driving
Starting and driving
Starting
Servicing
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company.
Copyright
1998 Ford Motor Company
Contents
2
5
22
82
107
112
144
169
212
223
235
236
1

Advertisement

Table of Contents
loading

Related Manuals for Ford 1999 F-350

Summary of Contents for Ford 1999 F-350

  • Page 1 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright 1998 Ford Motor Company...

  • Page 2: Introduction

    INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.
  • Page 3 Light Truck Body Builders Advisory Service 1–800–635–5560. Use of your Ford light truck as an ambulance, without the Ford Ambulance Preparation Package voids the Ford New Vehicle Limited Warranty and may void the Emissions Warranties. In addition, ambulance...
  • Page 4 You can determine whether the ambulance manufacturer followed Ford’s recommendations by directly contacting that manufacturer. Ford Ambulance preparation package is only available on certain 7.3L Diesel engine equipped vehicles. Notice to owners with vehicles equipped with Power Take Off...

  • Page 5: Instrumentation

    Instrumentation...
  • Page 6 Instrumentation Turn signal and wiper/washer control (pg. 72) BRAKE Headlamp control (pg. 22) Instrument panel dimmer switch (pg. 23) * if equipped Instrument cluster (pg. 8) Speed control* (pg. 67) FUEL FILL FUEL 0 0 0 0 0 0 0 0 0 km/h RPM 1000 P R N...
  • Page 7 Instrumentation Gearshift lever Electronic sound system (pg. 116) (pg. 29) Auxiliary power point Passenger air bag (pg. 24) deactivate switch (pg. 96) Climate control system (pg. 24) 4WD control * (pg. 128)
  • Page 8 Instrumentation WARNING LIGHTS AND CHIMES FUEL FILL FUEL BRAKE Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge. The light comes on when there is approximately 1/16th of a tank indicated on the fuel gauge (refer to Fuel Gauge in this chapter for more information).
  • Page 9 What you should do if the Check Engine/Service Engine Soon light illuminates Light turns on solid: This means that the OBD I system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1.
  • Page 10 Instrumentation What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1.
  • Page 11 (TCIL). The TCIL may flash steadily if a malfunction is detected. If the TCIL is flashing, contact your Ford dealer as soon as possible. If this condition persists, damage to the transmission could occur. Safety belt...
  • Page 12 Instrumentation Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb. Refer to Exterior bulbs in the Maintenance and care chapter.
  • Page 13 Instrumentation Door ajar Illuminates when the ignition is in the ON or START position and any DOOR door is open. AJAR Oil pressure/Engine coolant This light will illuminate when the ignition is in the ON position and the: • engine coolant temperature is very high •...
  • Page 14 Instrumentation GAUGES FUEL FILL FUEL BRAKE Fuel gauge Displays approximately how much fuel is in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
  • Page 15 Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
  • Page 16 Instrumentation Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer in the red zone may damage the engine. Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position.
  • Page 17 Instrumentation Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the “L” and “H”). If the gauge indicates low pressure, stop the vehicle as soon as safely possible and switch off the engine immediately.
  • Page 18 Instrumentation Mode control Each press of the MODE control will display a different feature as follows: Average fuel economy. The display will indicate the vehicle’s average fuel economy in liters/100 km (or miles/gallon) since the average fuel economy was last reset. If you calculate your average fuel economy by dividing liters of fuel used by 100 kilometers traveled...
  • Page 19 Instrumentation • if the vehicle is started while parked on an incline. • if less than 30 liters (8 gallons) of fuel is added to the fuel tank. The fuel range function will flash for 5 seconds at the following distances based on fuel remaining and fuel economy calculations: •...
  • Page 20 Instrumentation Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Locate the trip computer on the overhead console. 3. Turn ignition to the ON position. 4. Press and hold both trip computer controls.
  • Page 21 Instrumentation Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Locate the trip computer located in the overhead console. 2.

  • Page 22: Controls And Features

    Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: •...
  • Page 23 Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (past detent) to turn on interior lamps.
  • Page 24 Controls and features AUXILIARY POWER POINT The auxiliary power point is located on the instrument panel. POWER POINT Do not plug optional electrical accessories into the cigarette lighter. Use the power point. CLIMATE CONTROL SYSTEM Heater only system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle.
  • Page 25 • (Panel) -Distributes outside air through the instrument panel registers. • OFF-Outside air is shut out and the fan will not operate. • (Panel and floor) -Distributes outside air through the instrument panel registers and the floor ducts. • (Floor) -Allows for maximum heating. Distributes outside air through the floor ducts.
  • Page 26 Controls and features Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or a sudden stop. Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle.
  • Page 27 • MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle.
  • Page 28 Controls and features Operating tips • In humid weather, select windshield from fogging. After a few minutes, select any desired position. • To prevent humidity buildup inside the vehicle, don’t drive with the climate control system in the OFF position. •...

  • Page 29: Using Your Audio System

    USING YOUR AUDIO SYSTEM AM/FM Stereo PUSH TONE AM/FM Stereo PUSH TONE AM / FM STEREO Controls and features SEEK TONE VOL TUNE AM/FM SEEK TONE VOL TUNE AM/FM...
  • Page 30 Controls and features Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
  • Page 31 Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there).
  • Page 32 Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. With the electronic AM/FM stereo, press the TONE control once, then use the volume knob to adjust the level. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output.
  • Page 33 Setting the clock Press CLK to toggle between listening frequencies and clock mode. To set the hour, press and hold the CLK control and press: • to decrease hours and • to increase hours. To set the minute, press and hold the CLK control and press: •...
  • Page 34 Controls and features reverting back to the clock. In media mode, the media information will always be displayed. AM/FM stereo cassette VOL - PUSH ON BASS TREB SEEK SCAN TUNE Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume.
  • Page 35 If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and tape modes.
  • Page 36 Controls and features Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Scan function The scan function works in radio mode.
  • Page 37 Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
  • Page 38 Controls and features Tape select • To enter tape mode while in radio mode, press the TAPE AMS control. Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection.
  • Page 39 Dolby noise reduction Dolby noise reduction operates only in tape mode. Dolby reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby noise reduction. The noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation.
  • Page 40 Controls and features • to decrease minutes and • to increase minutes. The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for ten seconds, when the radio is turned on, and then revert to clock information.
  • Page 41 Controls and features Volume/power control Press the control to turn the audio VOL - PUSH ON system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control.
  • Page 42 Controls and features Tune adjust The tune control works in radio or CD changer mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.
  • Page 43 Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in tape mode • Press to listen to the previous selection on the tape. •...
  • Page 44 Controls and features Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again.
  • Page 45 Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
  • Page 46 Controls and features Press the TREB control then press: • to decrease the treble output • to increase the treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: •...
  • Page 47 Tape/CD select • To begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function.
  • Page 48 Controls and features Eject function Press the EJ control to stop and eject a tape. Press the EJ control to stop and eject a CD. Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) the noise reduction.
  • Page 49 Setting the clock To set the hour, press and hold the CLK control and press SEEK: • to decrease hours and • to increase hours. To set the minute, press and hold the CLK control and press TUNE: • to decrease minutes and •...
  • Page 50 Controls and features The CLK button will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for ten seconds, when the radio is turned on, and then revert to clock information.
  • Page 51 Controls and features Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operation selected will be lit, while the controls which have no function for that mode will be turned off.
  • Page 52 Controls and features AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play. AM/FM select in CD mode Press this control to stop CD play and begin radio play.
  • Page 53 Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in tape mode • Press to listen to the previous selection on the tape. •...
  • Page 54 Controls and features Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again.
  • Page 55 Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
  • Page 56 Controls and features Press the TREB control then press: • to decrease treble output and • to increase treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: •...
  • Page 57 Tape/CD/CD changer (if equipped) select • To begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function.
  • Page 58 Controls and features Tape direction select Press SIDE 1–2 to play the alternate SIDE 1-2 side of a tape. Eject function Press the control to stop and eject a tape and/or a CD. Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during tape playback.
  • Page 59 Setting the clock Press the clock/RDS control until SELECT HOUR is displayed and press: • to decrease hours and • to increase hours. To set the minute, press the clock/RDS control until SELECT MIN is displayed and press: • to decrease minutes and •...
  • Page 60 Controls and features Radio Data System (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations. Press and hold the control for three seconds to turn the feature on or off. Press the control to scroll through the following selections: RDS traffic announcement •...
  • Page 61 RDS select program type • Press the RDS control until FIND program type is displayed. • Use the SEL control to select the program type. With the feature on, use the SEEK or AUTOSET or SCAN control to find the desired program type from the following selections: •...
  • Page 62 Controls and features • Use the SEL control to select TYPE, NAME, TEXT or NONE. When your radio is turned to a RDS station, RDS station TYPE, station NAME, or TEXT message will be displayed along with the frequency. Press SEL in order to scroll through the text messages.
  • Page 63 Press to eject the magazine. Make sure only one disc is inserted in each slot. Each disc must be inserted with the label surface upward. Depending on your system, you may insert up to six or ten CDs. The magazine does not need to be full for the changer to operate.
  • Page 64 Controls and features Troubleshooting the CD changer (if equipped) The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case. If sound skips: • You may be traveling on a rough road, playing badly scratched discs or the disc may be dirty.
  • Page 65 • Do not expose tapes to direct sunlight, high humidity, extreme heat or extreme cold. Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing. • Tighten very loose tapes by inserting a finger or pencil into the hole and turning the hub.
  • Page 66 Controls and features The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo. Audio system warranties and service Refer to the “Warranty Guide” for audio system warranty information. If service is necessary, see your dealer or a qualified technician.
  • Page 67 SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
  • Page 68 Controls and features To set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
  • Page 69 You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. To set a lower set speed • Press and hold CST/COAST. Release the control when the desired speed is reached or •...
  • Page 70 Controls and features To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped) Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
  • Page 71 To return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down.
  • Page 72 Controls and features HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers.
  • Page 73 Controls and features FLASH TO PASS Pull toward you to activate and release to deactivate. OVERDRIVE CONTROL (IF EQUIPPED) Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The overdrive function allows automatic upshifts to second, third and fourth gear.
  • Page 74 Controls and features POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. One touch down •...
  • Page 75 Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls. Accessory delay (if equipped) With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until...
  • Page 76 Controls and features 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash.
  • Page 77 Controls and features REMOTE ENTRY SYSTEM (IF EQUIPPED) The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition in the OFF position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting.
  • Page 78 Controls and features Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada.
  • Page 79 Controls and features To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation.
  • Page 80 Controls and features Replacing lost transmitters Take all your vehicle’s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed), perform the following procedure: To reprogram the transmitters yourself, place the key in the ignition and turn from OFF to ON eight times in rapid succession (within 10 seconds) ending in ON.
  • Page 81 TAILGATE LOCK (IF EQUIPPED) Your vehicle is equipped with a tailgate lock designed to prevent theft of the tailgate. • Insert ignition key and turn to the right to engage lock. • Turn ignition key to the left to unlock. Tailgate removal Your tailgate is removable to allow more room for loading.

  • Page 82: Seating And Safety Restraints

    Seating and safety restraints SEATING Full bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place. • Pull up on the release lever to quickly fold the seatback forward. 60/40 split bench seat (if equipped) •...
  • Page 83 Seating and safety restraints Captain’s chair (if equipped) • Lift the release bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • Pull the seatback handle up to recline the seat. • Push the release lever down to quickly fold the seatback forward.
  • Page 84 Seating and safety restraints Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Using the manual lumbar support Turn the lumbar support control toward the front of vehicle to increase firmness.
  • Page 85 Seating and safety restraints Rear folding bench seat (if equipped) Folding down the rear seats All safety belts should be properly stowed in the seat pockets before folding down the rear seat. Make sure that no objects such as books, purses or briefcases are on the floor in front of the second row seats before folding them down.
  • Page 86 Seating and safety restraints 1. Lift/rotate the seatback toward the rear of the vehicle and make sure it latches securely. 2. Lift/rotate the lower seat cushion to its seating position. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
  • Page 87 Seating and safety restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch.
  • Page 88 Seating and safety restraints Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode •...
  • Page 89 Seating and safety restraints • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
  • Page 90 Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
  • Page 91 (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced.
  • Page 92 Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIESEL FUEL ONLY km/h RPM x 1000 Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
  • Page 93 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide.
  • Page 94 Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system.
  • Page 95 Seating and safety restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is inflated, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
  • Page 96 If the light fails to illuminate when the passenger air bag switch is in the OFF position and the ignition switch is in ON, have the passenger air bag switch serviced at your Ford or Lincoln-Mercury dealer immediately. PASSENGER AIRBAG...
  • Page 97 If the light is illuminated when the passenger air bag switch is in the ON position and the ignition switch is in ON, have the passenger air bag switch serviced at your Ford or Lincoln-Mercury dealer immediately. The passenger side air bag should always be ON (the air bag OFF light...
  • Page 98 Seating and safety restraints Always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly. If a child in a rear facing infant seat must be transported in front, the passenger air bag must be turned OFF. This is because the back of the infant seat is too close to the inflating air bag and the risk of a fatal injury to the infant when the air bag inflates is substantial.
  • Page 99 Seating and safety restraints • although children ages 1 to 12 ride in the rear seat(s) whenever possible, children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat(s) of the vehicle; or •...
  • Page 100 Seating and safety restraints 2. Child age 12 or under: A child age 12 or under must ride in the front seat because: • my vehicle has no rear seat; • although children age 12 and under ride in the rear seat whenever possible, children age 12 and under have no option but to sometimes ride in the front seat because rear seat space is insufficient;...
  • Page 101 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
  • Page 102 Seating and safety restraints A belt-positioning booster should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion.
  • Page 103 (passenger side front and outboard rear seating positions)(if equipped). Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
  • Page 104 Seating and safety restraints Rear facing child seats should NEVER be placed in the front seats. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
  • Page 105 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
  • Page 106 Ford or Lincoln-Mercury dealer. If you have a SuperCab or Crew Cab, Ford recommends you attach tether safety seats in the rear seating position (if possible) with the tether strap attached to the tether anchorage bracket as shown in the instructions provided with the tether anchor kit.

  • Page 107: Starting

    PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
  • Page 108 Starting 2. Make sure the headlamps and vehicle accessories are off. If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: •...
  • Page 109 FUEL FILL FUEL BRAKE Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts.
  • Page 110 Starting Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below.
  • Page 111 Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch).

  • Page 112: Driving

    Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
  • Page 113 Using RABS • In an emergency, applying full pressure may cause the front wheels to lock. If the front brakes lock, the vehicle cannot be steered. You should apply the brakes with steadily increasing force, as if “squeezing” the brakes. If you feel the front wheels begin to lock, momentarily release the pedal and repeat the “squeeze”...
  • Page 114 Driving With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released. (If your brake warning lamp illuminates, have your vehicle serviced immediately). Using ABS •...
  • Page 115 Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
  • Page 116 Driving Extended use of other than the manufacturer’s specified size tires on a Traction-Lok rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver. To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire.
  • Page 117 Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician.
  • Page 118 Driving N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four. (Overdrive) can be deactivated by pressing the Transmission Control Switch (TCS) on the end of...
  • Page 119 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive).
  • Page 120 Driving 4. Turn ignition to position 5 (START) to start the engine, let the engine idle for a few seconds, then shift into gear. 5. Release the brake pedal. 6. Release clutch slowly while pressing down slowly on the accelerator pedal. •...
  • Page 121 Maximum downshift speeds 6-speed transmission Shift from: Transfer case position (if equipped) (Overdrive) - 4 72 km/h (45 mph) 4 - 3 56 km/h (35 mph) 3 - 2 32 km/h (20 mph) 2 - 1 8 km/h (5 mph) 1 - LO Use 2H or 4H for 4WD equipped vehicles.
  • Page 122 Driving 2. Set parking brake. 3. Shift into 1 (First). 4. Turn the ignition key to position 3 (OFF). Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully.
  • Page 123 With the 5-speed transmission you can shift into R (Reverse) only by moving the gearshift from left of 3 (Third) and 4 (Fourth) gears before you shift into R (Reverse). This is a special lockout feature that protects you from accidentally shifting into R (Reverse) when you downshift from (Overdrive).
  • Page 124 Driving Removing key from ignition • Turn the ignition key until it stops. • Push the release lever forward and rotate the key towards you and remove. POWER TAKE OFF (PTO) CAPABILITY (IF EQUIPPED) Some vehicles with 6.8L and 7.3L engines are equipped with Power Take Off (PTO) capability.
  • Page 125 FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) When Four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD power can be selected when additional driving power is desired. If equipped with the Electronic Shift 4WD System, and the instrument panel control is moved to 4WD Low while the vehicle is moving, the system will not engage and no damage will occur to the 4WD system.
  • Page 126 Driving • automatic hub locks can be manually overridden by rotating the hub lock control from AUTO to LOCK. Manual 4x4 system (if equipped) The 4WD system is engaged or disengaged by rotating the front wheel hub lock control from FREE to LOCK, then manually engaging the transfer case with a floor-mounted shifter.
  • Page 127 Shifting from 2H (2WD high) to 4H (4WD high) Engage the locking hubs by rotating the hub lock control from FREE to LOCK, then move the transfer case lever from 2H (2WD High) to 4H (4WD High). Do not shift into 4H (4WD High) with the rear wheels slipping.
  • Page 128 Driving 4. Move the transfer case shift lever through N (Neutral) directly to 4H (4WD High) or 4L (4WD Low). Using the N (Neutral) position The transfer case neutral position overrides the transmission and puts the vehicle in neutral regardless of transmission gearshift lever position.
  • Page 129 Shifting from 2WD (2WD high) to 4x4 HIGH (4WD high) Rotate the 4WD control to the 4x4 HIGH position at speeds up to 88 km/h (55 mph). • Do not shift into 4x4 HIGH with the rear wheels slipping. Shifting from 4x4 HIGH (4WD high) to 2WD (2WD high) Rotate the 4WD control to 2WD at any forward speed.
  • Page 130 Driving 4. Move the 4WD control to the 4x4 HIGH or 4x4 LOW position. Driving off-road with 4WD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain.
  • Page 131 Driving Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels.
  • Page 132 Driving If vehicle speed drops more than 16 km/h (10 mph), the speed control will cancel automatically. Resume speed with accelerator pedal. If speed control cancels after climbing the hill, reset speed by pressing and holding the SET ACCEL button to resume speeds over 50 km/h (30 mph).
  • Page 133 • GVWR (Gross Vehicle Weight Rating) : Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver’s door pillar. • GAWR (Gross Axle Weight Rating) : Carrying capacity for each axle system.
  • Page 134 Driving weight to the front of your vehicle, (potentially including weight added to the cab), the weight added should not exceed the Front Axle Reserve Capacity (FARC). Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways (i.e. restrict the number of passengers or amount of cargo carried).
  • Page 135 Driving through deep water where the transmission is submerged may allow water into the transmission and cause internal transmission damage. TOWING A TRAILER Your vehicle may tow a Conventional/Class IV trailer or fifth wheel trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and rear axle ratio on the following charts.
  • Page 136 Driving Trailer towing tables F-250 with manual transmission Engine Rear axle Maximum GCWR-kg ratio (lbs.) 5.4L 3.73 6 124 (13 500) 5.4L 4.10 6 804 (15 000) 6.8L 3.73 7 484 (16 500) 6.8L 4.30 8 165 (18 000) Conventional/Class IV trailer hitch only. Fifth wheel trailer maximum weights can be calculated by subtracting GVW from GCWR.
  • Page 137 F-350 with automatic transmission Engine Rear axle Maximum GCWR-kg ratio 5.4L 3.73 6 124 (13 500) 5.4L 4.10 6 804 (15 000) 6.8L 3.73 7 711 (17 000) 6.8L 4.30 9 072 (20 000) Conventional/Class IV trailer hitch only. Fifth wheel trailer maximum weights can be calculated by subtracting GVW from GCWR.
  • Page 138 Driving Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle’s bumper or attach to the axle.
  • Page 139 Trailer brakes Electric brakes and manual, automatic or surge-type brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system.
  • Page 140 Driving Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Scheduled Maintenance guide for more information. Trailer towing tips • Practice turning, stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination.
  • Page 141 N (Neutral) position in order to tow with all wheels on the ground. SNOWPLOWING For low speed snow removal, Ford offers a Snowplow Package as an option. If you do not have this equipment, do not use your vehicle as a snowplow or powertrain and suspension system damage may occur.
  • Page 142 Driving • After installing a snowplow to the vehicle, ensure the vehicle’s front toe alignment and front ride height are within specification (reset if required). These specifications are located in the vehicle’s Workshop Manual. Adherence to the toe, tire pressures and ride height specification is important for proper tire wear, ride, handling and headlight aim.
  • Page 143 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Engine temperature while plowing When driving with a plow, your engine may run at a higher temperature than normal because the attached snowplow blade will restrict airflow to the radiator.

  • Page 144: Roadside Emergencies

    Roadside emergencies HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column.
  • Page 145 Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button.
  • Page 146 Roadside emergencies Standard fuse amperage rating and color Fuse Mini Standard Rating Fuses Fuses Grey Grey Violet Violet Pink Pink 7.5A Brown Brown Blue Blue Yellow Yellow Natural Natural Green Green — — — — — — — — — —...
  • Page 147 To remove a fuse use the fuse puller tool provided on the fuse panel cover. The fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating Electronic Flasher Instrument Cluster, Powertrain Control Module (PCM) Keep Alive Memory Cigar Lighter, OBDII Glove Box Lamp, Map Lamps, Power Mirrors, Underhood Lamp —...
  • Page 148 Roadside emergencies Fuse/Relay Fuse Amp Location Rating Radio, Headlamp Switch Illumination — Not Used — Not Used Washer Pump, Wiper Run/Park Relay Coil, Wiper Hi/LO Relay Coil, Washer Pump Relay Coil Horn Stop Lamps, Center High-mount Stop Lamp, Trailer Tow Stop Lamp Dome Lamp, Cargo Lamp, Courtesy Lamps Generic Electronic Module (GEM), Powertrain Control Module (PCM),...
  • Page 149 Fuse/Relay Fuse Amp Location Rating Ignition Run Power Feed (Customer Access) Brake Shift Interlock, DRL Relay Coil, Speed Control Module, Backup Lamps, Trailer Tow Backup Lamp Relay Coil, Electronic Shift On The Fly Hub Lock Solenoid Instrument Cluster (Charge and Airbag Warning Lamps) PCM Relay Coil, Ignition Coil (Gasoline only), Fuel Heater (Diesel only), Wastegate...
  • Page 150 Roadside emergencies The high-current fuses and relays are coded as follows. Fuse/Relay Fuse Amp Location Rating 7.5A * Trailer Tow Left Stop/Turn Lamp 10A* Air Bag Module 7.5A* Trailer Tow Right Stop/Turn Lamp 20A* Trailer Tow Backup Lamps, Trailer Tow Park Lamps 20A* Gasoline only-PCM, Two Speed Fuel Pump...
  • Page 151 Fuse/Relay Fuse Amp Location Rating 20A* Gasoline only-Vapor Managment Valve, (Gasoline HEGO Sensors, Intake Manifold only) Communication Control, EVR Solenoid, 5A* (Diesel PCM, Canister Vent Solenoid only) Diesel only-Dual Alternator A Field 15A* Trailer Tow Electronic Brake Illumination, Park Lamps, Trailer Tow Park Lamp Relay Coil 10A* Left Headlamp...
  • Page 152 Roadside emergencies Fuse/Relay Fuse Amp Location Rating Gasoline only-Not Used (Gasoline Diesel only-Injector Driver Module only) 30A* (Diesel only) 30A** Trailer Tow Electronic Brake Controller 20A** Radio PCM Power Relay Blower Motor Relay Two Speed Fuel Pump Relay (Gasoline only), Injector Driver Module Power Relay (Diesel only) Washer Pump Relay Windshield Wiper Park/Run Relay...
  • Page 153 If your vehicle is equipped with 4WD, a spare tire of a different size than the road tires should not be used. Such a tire could result in damage to driveline components and make the vehicle difficult to control. Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool...
  • Page 154 Roadside emergencies 2. The following steps are required to move the support bracket (if equipped) away from the spare tire: • With tapered end of lug wrench, loosen the eyebolt on the support bracket. • Line up the eyebolt with the slot in the support bracket.
  • Page 155 5. The following steps are required to secure the support bracket (if equipped) under the spare tire: • Move the support bracket over the spare tire. • Slide the support bracket over the eyebolt into the slot on the support bracket.
  • Page 156 Roadside emergencies 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park) (automatic transmission) or R...
  • Page 157 Roadside emergencies • Front (4x2) • Front passenger side (4x4)
  • Page 158 Roadside emergencies • Front driver side (4x4) Make sure the jack fits into the notched area on the differential housing. • Rear...
  • Page 159 Roadside emergencies 8. Turn the jack handle clockwise until the wheel is completely off the ground and high enough to install the spare tire. 9. Remove the lug nuts with the lug wrench. 10. On single rear wheel vehicles, replace the flat tire with the spare tire, making sure the valve stem is facing outward for all front tires and vehicles equipped with single rear...
  • Page 160 Roadside emergencies • Front (4x2) • Front driver side (4x4) • Front passenger side (4x4)
  • Page 161 Roadside emergencies • Rear 14. Insert the jack handle into the pump linkage. 15. Use an up-and-down motion with the jack handle to raise the wheel completely off the ground. Hydraulic jacks are equipped with a pressure release valve that prevents lifting loads which exceed the jack’s rated capacity.
  • Page 162 M14 x 1.5 200-225 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. On all two-piece flat wheel nuts, apply one drop of motor oil between the flat washer and the nut. Do not apply motor oil to the wheel nut threads or the wheel stud threads.
  • Page 163 JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted.
  • Page 164 Roadside emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
  • Page 165 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
  • Page 166 Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
  • Page 167 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
  • Page 168 However, a slingbelt with T-hooks and a wheel dolly can also be used. Ford Motor Company provides a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for...

  • Page 169: Maintenance And Care

    SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
  • Page 170 Maintenance and care Working with the engine off • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. •...
  • Page 171 Maintenance and care OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch located under the right center of the hood. Slide the handle to release the auxiliary latch.
  • Page 172 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine oil dipstick 2. Clutch fluid reservoir (manual transmission) 3. Brake fluid reservoir 4. Power distribution box 5. Power steering fluid reservoir 6. Air filter assembly 7. Engine coolant reservoir 8.
  • Page 173 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). 4.
  • Page 174 Motor oil displaying the API Certification Trademark will meet all requirements for your vehicle’s engine. Ford oil specification is WSS-M2C153-G. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty.
  • Page 175 Maintenance and care Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced.
  • Page 176 Check the clutch fluid level. Refer to the Scheduled Maintenance Guide for the service interval schedules. Use only a DOT 3 brake fluid designed to meet Ford specifications. Refer to Capacities and specifications. For vehicles equipped with the 5–speed manual transmission, during normal operation, the fluid level in the clutch reservoir should remain constant.
  • Page 177 1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir. 2. Remove cap and rubber diaphragm from reservoir. 3. Add fluid until the level reaches the step in the reservoir. 4. Reinstall rubber diaphragm and cap onto reservoir.
  • Page 178 Oregon, F5FZ-19549–CC, in Canada, Motorcraft CXC-10) or a premium engine coolant that meets Ford specification ESE-M97B44–A. • DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544–AA (orange in color). • DO NOT USE a DEX-COOL engine coolant or an equivalent engine coolant that meets Ford specification WSS-M97B44–D.
  • Page 179 • DO NOT MIX recycled coolant and conventional coolant together in your vehicle. Mixing of engine coolants may harm your engine’s cooling system. • The use of an improper coolant may harm engine and cooling system components and may void the warranty of your vehicle’s engine cooling system.
  • Page 180 Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and use of such coolant may harm engine and cooling system components.
  • Page 181 How fail-safe cooling works If the engine begins to overheat: • the engine coolant temperature gauge will move to the red (hot) area. • the symbol will illuminate. • the symbol will illuminate. • the Service Engine Soon indicator light will illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation.
  • Page 182 Maintenance and care Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the “Service Guide” for the service interval schedules.
  • Page 183 Maintenance and care operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature.
  • Page 184 Maintenance and care The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
  • Page 185 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
  • Page 186 Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication.
  • Page 187 BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
  • Page 188 Maintenance and care When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
  • Page 189 • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective.
  • Page 190 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
  • Page 191 Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
  • Page 192 Maintenance and care • Four tire rotation • Five tire rotation...
  • Page 193 Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford. Do not replace your tires with “high performance” tires or larger size tires.
  • Page 194 Maintenance and care The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. If you need to use chains, it is recommended that steel wheels (of the same size and specifications) be used as chains may chip aluminum wheels.
  • Page 195 Automotive fuels can cause serious injury or death if misused or mishandled. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling.
  • Page 196 Maintenance and care When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container.
  • Page 197 It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high quality fuel. Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE.
  • Page 198 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
  • Page 199 driving (engine break-in period). You will get a more accurate measurement after 3 000 km–5 000 km (2 000 miles-3 000 miles). Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill Capacities chart in this “Owner Guide.”...
  • Page 200 Maintenance and care 5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used. Keep a record for at least one month and record the type of driving (city or highway).
  • Page 201 • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy.
  • Page 202 Guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
  • Page 203 Maintenance and care sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine.
  • Page 204 Maintenance and care • Tail lamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs (aerodynamic) Handle a halogen headlamp bulb carefully and keep out of children’s reach.
  • Page 205 Maintenance and care Replacing headlamp bulbs (sealed beam) To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position. 2. Open the hood. 3. Remove the two screws and parking lamp/side marker assembly by pulling gently 4. Disconnect the electrical connectors from the parking lamp/side marker assembly and remove.
  • Page 206 Maintenance and care Replacing tail lamp/Backup lamp bulbs The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies.
  • Page 207 To install the brakelamp assembly: 1. Install the bulb into the lamp assembly and rotate clockwise. 2. Install the lamp assembly on the vehicle with two screws. Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper. To change the license plate lamp bulbs: 1.
  • Page 208 • The headlamp beams are pointed substantially away from a slightly down and to the right position. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water.
  • Page 209 Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), touch-up paint (#ALBZ-19500–XXXXA), or aerosol paint spray (#ALAZ-19500– XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring. Observe the application instructions on the products.
  • Page 210 Maintenance and care Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Use glass cleaner or tar remover if necessary.
  • Page 211 For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label.

  • Page 212: Capacities And Specifications

    *Refer to the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for Motorcraft diesel engine service part numbers. **Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Ford Part Name Front axle Motorcraft SAE 75W90 Axle Lubricant 1,2,3 Rear axle...
  • Page 213 Capacities and specifications Fluid Ford Part Name Engine Premium Engine coolant Coolant Engine oil Motorcraft 5W-30 (includes Super Premium filter change)- Motor Oil Gas engines Engine oil Refer to your 7.3L Diesel Supplement (includes filter change)- Diesel engine Fuel tank...
  • Page 214 Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter.
  • Page 215 Capacities and specifications LUBRICANT SPECIFICATIONS Ford part Item name or equivalent Motorcraft SAE Front axle 75W90 Axle (4X4) Lubricant Motorcraft SAE 75W140 High Performance Synthetic Rear Axle Lube Motorcraft SAE 75W90 Synthetic Rear axle Rear Axle Lube (Dana 80 axles)
  • Page 216 Add 236 ml (8 oz.) of additive friction modifier C8AZ-19B546–A, Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. Ford design rear axles contain a synthetic lubricant that does not require changing unless the axle has been submerged in water. Dana rear axles also contain a synthetic lubricant but do require a change.
  • Page 217 Capacities and specifications ENGINE DATA Engine 5.4L V8 engine Cubic inches Horsepower 235 @ 4250 rpm Torque 335 lb.-ft. @ 3000 rpm 410 lb.-ft. @ 2650 rpm Required fuel 87 octane Firing order 1-3-7-2-6-5-4-8 1.3-1.4 mm Spark plug gap (0.052-0.056 inch) Ignition system Coil on plug Compression ratio...
  • Page 218 Capacities and specifications F250-Crew cab Dimension Crew Cab 4x2 (1) Overall height 1 960 mm (77.2 in) 1 883 mm (74.1 in) (2) Track (Front / 1 745 mm (68.7 in)/ Rear) 1 729 mm (68.1 in) (3) Overall width 1 988 mm (78.3 in) (4) Wheelbase 3 967 mm (156.2 in )
  • Page 219 Capacities and specifications (5) Overall 5 732 mm 5 754 mm length (225.7 in) (226.5 in) Short wheel base Long wheel base Single rear wheels Dual rear wheels F350-Crew cab Dimension Crew Cab 4x2 (1) Overall height 1 929 mm (75.9 in) (2) Track (Front / 1 745 mm (68.7 in)/ Rear)
  • Page 220 Capacities and specifications 3 576 mm 4 186 mm Wheelbase (140.8 in) (164.8 in) (5) Overall 5 732 mm length (225.7 in) 6 341 mm (249.6 in) Short wheel base Long wheel base F550 Dimension Chassis Chassis Cab 4x2 Cab 4x4 (1) Overall 2 076 mm 2 075 mm...
  • Page 221 Capacities and specifications...

  • Page 222: Certification Label

    The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped). MFD. BY FORD MOTOR CO. IN U.S.A. DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG FGAWR: XXXXXX/XXXXXXX...

  • Page 223: Customer Assistance

    GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week •...
  • Page 224 5,200 participating Ford, Lincoln-Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information. Since this information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options.
  • Page 225 Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs.
  • Page 226 THE DISPUTE SETTLEMENT BOARD The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford...
  • Page 227 • a Ford or Lincoln/Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln-Mercury dealership management, recognized for their business leadership qualities. What the Board needs To have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application form.
  • Page 228 • the name of the dealer who sold or serviced the vehicle • a brief description of your unresolved concern • a brief summary of the action taken by the dealer(s) and Ford Motor Company • the names (if known) of all the people you contacted at the dealership(s) •...
  • Page 229 Customer assistance the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law. To Request a DSB Brochure/Application For a brochure/application, speak to your dealer or write/call to the...
  • Page 230 Ford Motor Company Worldwide Direct Market Operations. FORD ACCESSORIES FOR YOUR VEHICLE Ford has many quality products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following or products of equivalent quality:...
  • Page 231 In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigid engineering and safety specifications. Ford accessories are warranted for...
  • Page 232 Customer assistance Travel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.0L only) Off road lights Pickup box rails Removable luggage rack Removable luggage rack adapters Retractable bed hooks and loops Running boards...
  • Page 233 Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rallye bars Rear air deflectors Rear decklid spoilers Side window air deflectors Spare tire lock Step bumpers Step/sill plates...
  • Page 234 • Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment. ORDERING ADDITIONAL OWNER’S LITERATURE...

  • Page 235: Reporting Safety Defects

    However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.

  • Page 236: Index

    ...119 recommended shift speeds ...120 Compass, electronic ...19 calibration ...21 set zone adjustment ...20 Console ...76 Controls power seat ...83 Coolant ...178,180 checking and adding ...178 refill capacities ...180,212 specifications ...215,217 Customer Assistance ...223 Ford accessories for your vehicle ...230...
  • Page 237 Ford Extended Service Plan ...224 Getting assistance outside the U.S. and Canada ...229 Getting roadside assistance ...223 Getting the service you need ...225 Ordering additional owner’s literature ...234 The Dispute Settlement Board ...226 Dipstick engine oil ...172 Doors door ajar warning ...13 Driveline universal joint and slip yoke ...186...
  • Page 238 Index GAWR (Gross Axle Weight Rating) ...132 calculating ...134 definition ...132 driving with a heavy load ...132 location ...132 GVWR (Gross Vehicle Weight Rating) ...132 calculating ...132,134 definition ...132 driving with a heavy load ...132 location ...132 Hazard flashers ...144 Headlamps ...22 aiming ...208 daytime running lights ...22...
  • Page 239 Parking brake ...114 Parts (see Motorcraft parts) ...212 Power distribution box (see Fuses) ...149 Power door locks ...75 Power steering ...115 fluid, checking and adding ...182 fluid, refill capacity ...212 fluid, specifications ...215,217 Radio ...29 Relays ...145 Remote entry system ...77,78 illuminated entry ...79 locking/unlocking doors ...77 panic alarm ...78...
  • Page 240 Index Vehicle Identification Number (VIN) ...222 Vehicle loading ...132 Ventilating your vehicle ...111 Warning chimes ...13 Warning lights (see Lights) ...8 Washer fluid ...177 Water, Driving through ...134 Windows power ...74 Windshield washer fluid and wipers checking and cleaning ...189 operation ...72 replacing wiper blades ...189 Wrecker towing ...168...

  • Page 248: Filling Station Information

    Refer to Refill capacities in the Capacities and specifications chapter. Engine oil (includes 5.7L (6.0 quarts). Use Motorcraft 5W30 Super filter change) Premium Motor Oil, Ford specification WSS-M2C153-G. Tire size and pressure Refer to the Certification Label inside of driver’s door Hood release Pull handle under the left side of the instrument panel.

This manual is also suitable for:

F-350 1998F-250 1998

Table of Contents