System Operations; Arming The System In Away Mode; Disarming The System From Away Mode - Bosch ICP-CC404 Installation Manual

ICP-CC404 | Installation Guide | 4.0
Zone Isolating Mode
This indicator (the person) flashes once
every 3 sec when you attempt to isolate
zones or program zones to automatically
isolate for STAY Mode 2.
Flashing
For more information, refer to:
•
Section 4.11 on page 21 to manually isolate zones.
•
Section 6.1.4 on page 30 to use the Installer Code
to set zones to automatically isolated in STAY
Mode 2.
•
Section 6.2.5 on page 35 to use the Master Code
to set zones to automatically isolate in STAY
Mode 2.
Fault Indicator
The fault indicator lights when the
system detects a system fault (refer to
Table 12 on page 17). Refer to Section
4.12 Fault Analysis Mode on page 22 for
more information on system faults.
Each time a new system fault is detected (the fault
indicator flashes), the codepad beeps once per
minute. Press [AWAY] to stop the beeping and
acknowledge the fault.
Programming Mode
These two indicators flash when you
enter Installer's Programming Mode or
use any Master Code function.
Flashing
OFF Indicator/Zone Sealed
The OFF indicator lights when the
system is disarmed and flashes when a
zone becomes unsealed when disarmed.
The indicator stops flashing when all
zones are sealed.
ON Indicator/Zone in Alarm
The ON indicator lights when the system
is armed and flashes when an alarm
occurs. The indicator resets after a valid
User Code is entered.
Audible Indicators
The codepad provides a number of audible
indications. Refer to Table 13 on page 17.

4.0 System Operations

This section explains the general operations of the
system: arming and disarming the system in the three
modes, isolating zones, initiating codepad alarms, and
determining a fault.
4.1

Arming the System in AWAY Mode

Arming the system in AWAY Mode is normally
performed when you leave the premises and want all
zones ready to detect an intrusion.
18
System Operations
There are two different methods to arm the system in
AWAY Mode. You can always use the first method.
You can use the other method only if Option 2 is
enabled in Location 429 (refer to Section 18.6
Consumer Options 2 on page 75).
If you must isolate a zone(s) before arming the system
in AWAY Mode, refer to Section 4.11 Isolating Zones
on page 21.
To arm the system in AWAY Mode (method one):
Enter your code and press [AWAY].
Two beeps sound, the AWAY indicator lights, and
Exit Time starts.
To arm the system in AWAY Mode (method two):
1. Press and hold [AWAY].
2. When two beeps sound, release the button.
The AWAY indicator lights and Exit Time starts.
If a zone is not sealed at the end of Exit Time, the
zone is automatically isolated and its indicator lights
on the remote codepad. The zone becomes an active
part of the system again after it is resealed. For
example, if a window is open when Exit Time
expires, the window is not an active part of the
system until it is closed. Opening the window after
Exit Time expires causes an alarm.
Forced Arming
Arming the system when a zone is not sealed is
known as forced arming. Refer to Section 14.3.6 Zone
Options 2 on page 58 to enable forced arming for each
zone.
If the AWAY indicator does not light and a long beep
sounds when you attempt to arm the system in
AWAY Mode, forced arming is not permitted. If this
is the case, you seal all zones or manually isolate
them before you can arm the system.
4.2 Disarming the System from AWAY
Mode
When you enter the premises after the system is
armed in AWAY Mode, you must disarm the system
from AWAY Mode to disable detection devices that
activate the siren, strobe, and bell outputs.
If there was an alarm before disarming the system
from AWAY Mode, a zone indicator flashes to
indicate a previous alarm in that zone.
To disarm the system from AWAY Mode:
Enter your code and press [AWAY].
Bosch Security Systems, Inc. | 12/08 | F01U089401-02
Single button arming in AWAY Mode
reports as User Code number 16.
Select Option 2 in Location 429 to
enable single button arming in AWAY
Mode (refer to Section 18.6 Consumer
Options 2 on page 75).