Tyre Pressure; Changing Engine Oil - Stiga RANGER Instructions For Use Manual

can be found in the service log and the actions are
described under "4 STARTING AND OPERA-
TION" as well as below.
Servicing carried out at an authorised workshop
guarantees professional work using genuine spare
parts.
At each basic service and intermediate service car-
ried out at an authorised workshop, the service log
is stamped. A service log presenting these services
is a valuable document that improves the ma-
chine's second-hand value.
5.2 Preparation
All service and all maintenance must be carried out
on a stationary machine with the engine switched
off.
Prevent the machine from rolling by al-
ways applying the parking brake.
Stop the engine.
Prevent unintentional starting of the
engine by disconnecting the spark plug
cable(s) from the spark plug(s) and re-
moving the ignition key.

5.3 Tyre pressure

Adjust the air pressure in the tyres as follows:
Front: 0.6 bar (9 psi).
Rear: 0.4 bar (6 psi).

5.4 Changing engine oil

This section contains tables covering the different
engines that are included in STIGA's Pro range. To
facilitate reading, mark the data that applies to the
relevant machine/engine.
5.4.1 Change intervals
The table below states hours of operation and cal-
endar months. Carry out the relevant action at
whichever occurs first.
1st time
Machine
Ranger, President, Hours of operation/
(B&S) Calendar months
Changing the oil
5 hours
Excellent (B&S) Hours of operation/
Calendar months
Changing the oil
5 hours
Changing the filter
Power (Kohler) Hours of operation/
Calendar months
Changing the oil
Changing the filter
ENGLISH
Change the oil more frequently if the engine has to
operate in demanding conditions or if the ambient
temperature is high.
5.4.2 Engine Oil
Use syntetic oil according to the table below.
Oil
Service class
Use oil without any additives.
Do not fill with too much oil. This can cause the
engine to overheat.
Change oil when the engine is warm.
1. Attach the clamp on the oil drainage hose. Use
2. Move the clamp up 3-4 cm on the oil drainage
3. Collect the oil in a collection vessel.
4. Hand in the oil for disposal in accordance with
5. Install the oil drainage plug and move the clamp
6. Remove the dipstick and fill with new oil.
Oil quantity:
Ranger
President
Power
Excellent
7. After filling up the oil, start the engine and idle
Then at
8. Check to see if there is any oil leakage.
intervals of
9. Stop the engine. Wait for 30 seconds and then
5.4.3 Oil filter(Power)
50 hours/
The oil filter must be replaced during every second
12 months
oil change, i.e. after 200 hours of operation. First
drain the engine oil and install the oil drainage plug
as described above. Then replace the oil filter as
50 hours/
follows:
12 months
1. Clean the area around the filter and dismantle
100 hours
2. Place the new filter with the hole facing up-
- 100 hours
200 hours
SAE 10W-40
SJ or higher
The engine oil may be very hot if it is
drained off directly after the engine is
shut off. Therefore allow the engine to
cool a few minutes before draining the
oil.
a polygrip or similar. See fig. 15-17:Y.
hose and pull out the plug.
NOTE! Do not spill any oil on the drive belts.
local provisions.
back so that it clamps above the plug.
Machine Oil volume, approx.
No filter
replacement
-
-
1,9 liter
1,6 liter
for 30 seconds.
check the oil level in accordance with 4.2.
the filter.
wards in a vessel.
EN
Filter replace-
ment
1,6 liter
1,6 liter
2,0 liter
1,7 liter
61