Ambush Code - NAPCO Gemini GEM-P3200 Installation Instructions Manual

Page 22
message) displayed. Note: (1) Keypads may be programmed for access only, eliminating their arm/disarm function
(keypad will then normally display "   
 ". (2) Keypad access may be logged into the event log by keypad.

Ambush Code

The Ambush Code is a two-digit code entered by the user just prior to disarming, typically to cause a silent report to be
sent to the central station. Thus, should the user be forced to disarm by an assailant, he can silently signal an emergency
while appearing to be merely disarming the panel. (Check the glossary for programming required to enable this feature.)
Ambush Code should not contain digits used as the first two digits of any user code.

Zone Descriptions (GEM-RP1CA/RP1CAe/RP1CAe2 only.)
Zone descriptions follow the Program Code in the normal programming sequence ("01-" will appear in the display).
Program the description, up to two lines, letter by letter. Buttons
Buttons will clear the entry at the cursor. When programming zone descriptions, buttons
will scroll not only through numbers 0-9, but through the alphabet and a series of punctuation marks and symbols as well.
(Roughly note the order in which the letters, numbers and symbols are displayed so that you will be able to determine the

proper direction to scroll, up or down, for fastest access. As familiarity improves, so will programming speed.) When the
description has been entered and is satisfactory as displayed (e.g. "GARAGE"), press the
To advance to the next zone (or to any other zone, for that matter), position the cursor over the displayed Zone Number,
i.e., "01" using buttons
zone-description programming procedure for the new zone. Advance to the next zone and repeat until all zones (up to 32)
have been programmed.
In the normal disarmed state, only the green STATUS LED will be on and the display will read "   
 ". To silence
an alarm, enter any User Code, then press the
Arm-Only Code may only be used to arm.
Arming
To arm, enter a valid User Code, then press the
(If a wrong code is entered, the keypad will display " 
    ".) The green STATUS LED will go off, the red
ARMED LED will go on, and the display will read "     " (" " representing the programmed exit-delay time, in
seconds). The exit delay will immediately start counting down toward "000", in 10-second decrements, indicating the
available time remaining to exit through an exit/entry door.
Note:
1. If Exit Delay Restart is enabled, after the panel is armed and the exit door is opened and then closed, exit delay will
restart at 60 seconds. If re-entry occurs within this 60-second interval, the alarm device will sound a 2-second
warning "chirp", if programmed, as an entry reminder to the user to return to the keypad and disarm.
2. (GEM-RP1CA/RP1CAe/RP1CAe2 only.) An "S" in the display (e.g. "      ") will appear as a reminder that
the system is being armed with the Service Code active. (To turn off the Service Code, disarm, then rearm using a
regular Arm/Disarm Code.)
3. If the System Trouble is displayed, there should be an attempt to correct the system trouble (for example by calling
an alarm maintenance or an alarm repairman). If this cannot be done, then press the
minutes to access the keypad without the system trouble displayed. Immediate attention should be provided, when
system troubles are encountered.
4. In commercial applications, if Start Exit Delay After Ringback is programmed, exit delay will not start until the
central station acknowledges receipt by a ringback tone at the keypad. The display will read "   " while the
control panel communicates to the central station. If the ringback tone does not sound within about 30 seconds,
the START EXIT TIME function may be used to manually start exit delay.
GEM-P3200 Installation Instructions

and . Change the Zone Number using buttons
button. Any valid User Code may be used to arm or disarm; an
 
and control the position of the cursor.
button.
WI817B 11/98

and

button to save it in memory.
and . Repeat the

button to allow 5
NAPCO Security Systems