NAPCO Gemini GEM-P3200 Installation Instructions Manual page 21

WI817B 11/98
This section provides a brief overview of system operation. For detailed operation, refer to the User's Guide furnished
with the keypad (OI193 for the GEM-RP1CA/RP1CAe/RP1CAe2; OI192 for the GEM-RP2AS/RP2ASe/RP2ASe2) and to
the Keypad Programming Modes at the end of this manual. NOTE: Keypad displays shown in this text are for the
GEM-RP1CA/RP1CAe/RP1CAe2 keypad. GEM-RP2AS/RP2ASe/RP2ASe2 displays will be similar, although abbrevi-
ated, and will scroll automatically.
(Refer to the GEM-P3200 Programming Instructions (WI818) for a detailed explanation of programming.) Up to 32
personal user codes may be programmed at the keypad. NOTE: The Authority Level and Access Byte associated with
each User Code may only be programmed in the Dealer Program Mode.
Default User Code
The first code programmed should replace the default (Level-3) code, "U01 123 • • • - • • - • • ", (1,2,3), which should
not be selected as a user code. Enter up to six digits (a minimum of four digits is recommended). The related Option Code
and Authority Level are programmable in the Dealer Program Mode only.
Each user should be assigned his own dissimilar code and should be cautioned against divulging his code to anyone
else. Thus should it become necessary to remove a user from the system, that one code may be cancelled without
affecting other codes, and that user would then be prevented from entry. NOTE: Napco's PCD3000 Quickloader Software
provides enabling and disabling User Codes at programmed times using the scheduling menus.
Changing or Canceling a Code
To change any code, merely program over the existing code as described in the Programming Instructions. Similarly, to
cancel a code, blank out each number of the code.
Arm/Disarm Code (Programmable in Dealer Program Mode only)
An Arm/Disarm Code may be used to arm/disarm the area in which it is programmed. Up to 6 digits may be programmed
or it may be programmed as a two-digit code for the purposes of quick arming.
Arm-Only Code (Programmable in Dealer Program Mode only)
An Arm-Only Code may only be used to arm the area in which it is programmed; it never has any disarm capability. Up to
6 digits may be programmed or it may be programmed as a two-digit code for the purposes of quick arming.
Service Code (Programmable in Dealer Program Mode only)
A Service Code is an Arm/Disarm Code that is easily activated when needed, and dormant at other times. Intended
for the occasional or temporary user (maid, repairman, etc.) who would otherwise be denied access to the premises, it is
programmed in conjunction with the Authority Level when programming User Codes. Refer to Programming Instructions.
It is activated by arming with it; an "S" will appear in the display (GEM-RP1CA/RP1CAe/RP1CAe2 only) after the
exit-delay countdown, indicating that a Service Code has been activated. It may then be used to arm and disarm just as
any other User Code. Service code can be armed/disarmed from a disarmed state, but it cannot be armed/disarmed from
an armed state, after another user code has been entered.
Panel Access Code
The Panel Access Code will trip the panel's Auxiliary Relay while disarmed if Access Control on Auxiliary Relay is
programmed. The Panel Access Code is programmed as any other User Code but without an accompanying Priority
Level. Caution: Do not use the same code as any Arm/Disarm Code. Note: These systems have not been investigated by
UL for compliance with UL294 (Access Control Systems).
Keypad Access Code (Programmable in Dealer Program Mode only)
Any User Code may have Keypad Access through a door with a striker by programming the keypad's Access Byte.
Program the Keypad Access Lug for the applicable keypads 1 through 8. If the Access Byte is programmed, that User
Code will function only an Access Code and not as an Arm/Disarm Code. Entering the code will cause a 5-second
active-low output on the PGM line with a pulsing sounder at the keypad and "    " (or other customized
NAPCO Security Systems
GEM-P3200 Installation Instructions
Page 21




 

        
 
    
 



  
NEXT/YES
   
PRIO R/NO
  
ARE A

  
   
R