Keypad Address - NAPCO Gemini GEM-P3200 Installation Instructions Manual

Page 18
This section will focus on configuring the GEM-RP1CA/RP1CAe/RP1CAe2 and GEM-RP2AS/RP2ASe/RP2ASe2 Keypads. If there is
more than one keypad in the system, only Keypad No. 1 may be used for programming.
Two types of keypads may be used with the GEM-P3200: the GEM-RP1CA/RP1CAe/RP1CAe2 and the GEM-RP2AS/RP2ASe/
RP2ASe2. Each must be assigned an address number (1–7) and each requires its own configuration procedure (see CONFIGUR-
ING THE KEYPADS, which follows, and DIRECT ADDRESS KEYPAD AREA OPTIONS). At least 1 keypad must be used; only 1 is
required for a single-area Commercial Burglary installation.
GEM-RP1CA/RP1CAE/RP1CAe2 - is a 2-line combination fire/burglary/access keypad capable of supporting 4 EZM zones and a
PGM output. A GEM-RP1CAe2 is recommended for use as Keypad #1.
GEM-RP2AS/RP2ASe/RP2ASe2 - is a utility LCD keypad combining several preset LCD words with a limited message line. NOTE:
Due to space constraints, available messages are abbreviated and will scroll automatically.
A total of up to 7 keypads may be connected to the panel. GEM-RP1CA/RP1CAe/RP1CAe2 and GEM-RP2AS/RP2ASe/
RP2ASe2 keypads may be intermixed but require different configuration procedures, as described in the following
paragraphs.
Configuring the GEM-RP1CA/RP1CAe/RP1CAe2 Keypad
Each GEM-RP1CA/RP1CAe/RP1CAe2 keypad must be configured for (a) keypad tactile beep; (b) entry sounder; (c)
keypad address; (d) compatibility number; (e) EZM address; and (f) zone response.


To enter the GEM-RP1CA/RP1CAe/RP1CAe2 Configuration Mode:
1. Move jumper JP5 (located at the upper-right corner of the control panel board) from Pins 1-2 (top two) to Pins
2-3 (bottom two). NOTE: See Wiring Diagram.
2. After about 15 seconds, the display will read "

   ", where XX indicates the keypad address.
3. Press
for all keypads.)


Press the button to continue or press the
To assign the keypad number, proceed as follows:


1. Enter the assigned keypad number 01–07, then press the
beep; an invalid number will be rejected by a long beep.
2. Press the button to continue or press the
GEM-P3200 Installation Instructions
and proceed as follows. (Repeat the following procedure
Keypad Tactile Beep
Upon entering the Keypad Configuration Mode, "     " will be displayed,

indicating that the tactile beep, which sounds when any button is pressed, is on. To
turn off the tactile beep, press the
beep on and off).
button to exit.

Entry Sounder
To turn off the keypad sounder during entry time, press the
will toggle the tactile beep on and off). Press the
the button to exit.

Keypad Address

If more than one keypad is installed, each must be assigned a unique
keypad address (that is, no two keypads may be numbered alike):
keypads must be numbered consecutively (missing numbers are not permitted)
only Keypad No. 1 may be used for programming.

button to save. A valid number will be acknowledged by a short
button to exit.
WI817B 11/98
NORMAL
KEYPAD
CONFIGURE
button (the button will toggle the tactile


button (the
button to continue or press
NAPCO Security Systems




 

        
 
    
 



  
NEXT/YES
   
PRIO R/NO
  
ARE A

  
   
R
button