Index - Janome 1200D Instruction Book

A
Accessories .............................................. 12, 38
Adjustments ........................................ 58, 82-90
B
Back-tack device ...................................... 10, 78
Balanced tensions .................................... 82-86
BLANKET STITCH ......................................... 44
C
Chain looper ................................ 10, 32, 70, 72
CHAINSTITCH ................................... 58, 82, 96
COVER HEM NARROW ................... 58, 86, 98
COVER HEM WIDE ........................... 56, 86, 98
Curves ............................................................. 94
Cutting width dial ............................... 12, 26, 90
D
DF (differential feed) .......................... 10, 24, 88
Display panel symbols .............................. 22-34
F
5-THREAD STITCH ........................................ 44
FLATLOCK 3 ................................................... 48
FLATLOCK 2 ................................................... 50
Foam pads ................................................ 14, 16
Foot control ........................................ 14, 18, 72
Foot pressure dial .............................. 10, 72, 98
Front cover ......................................... 10, 12, 74
H
Heavyweight fabrics ................................. 90, 92
I
Inside corners ................................................. 94
L
Light bulb ...................................................... 106
Locking upper knife ................................ 92, 106
Lower knife ...................................... 10, 90, 106
Lower looper ........................... 10, 12, 68, 84-86
N
NARROW HEM 3 ........................................... 48
Needle plate release lever ...................... 10, 104
Needle plate setting knob ............ 10, 18, 20, 30
Needle position ......................................... 24, 36
Needle threader .......................................... 8, 60
Needles ........................................ 10, 12, 24, 32

INDEX

O
Oiling ............................................................. 104
Outside corners .............................................. 94
OVERCAST 2 ........................................... 50, 86
Overlock cover ................................................ 30
OVERLOCK 3 ........................................... 46, 86
P
Power switch ............................................... 8, 16
Presser foot ........................... 10, 20, 30, 56, 76
Presser foot lever ..................................... 10, 76
Pressure adjustment dial ..................... 8, 74, 98
Programs ....................................... 8, 18, 20, 22
Q
Quick reference threading charts ............. 38-54
R
Removing stitches .......................................... 96
ROLLED HEM 3 ............................................. 48
ROLLED HEM 2 ............................................. 50
S
SAFETY 4 THREAD ....................................... 38
Sewing table ............................................. 12, 28
Side cover ................................................... 8, 10
SL (stitch length) .................................. 8, 22, 90
Snap-on thread guide ............................... 12, 36
Specialty threads ............................................ 14
Spool types ..................................................... 14
STRETCH KNIT STITCH ............................... 40
STRETCH WRAPPED .................................... 50
T
Tension adjustment dials ..................... 8, 32, 82
Tension release clips ................................ 12, 36
Tension release lever ........................... 8, 60, 80
Thread guide bar ............................................ 34
Thread guide pole .............................. 12, 14, 36
Thread cutter ............................................ 10, 76
Thread tension .................................... 34, 82-86
Threading charts ....................................... 38-45
3-THREAD STITCH WIDE ....................... 42, 78
Topstitching ................................................... 102
TRIPLE COVER HEM ............................ 52, 102
Turning corners ....................................... 96, 100
2 thread converter .................................... 10, 26
U
Upper knife .......................... 10, 12, 26, 92, 106
Upper looper ............................................. 10, 26
Upper knife position .................................. 26, 92
Upper knife replacement .............................. 106
W
Waste tray ................................................. 12, 74
111