Table of Contents
Advertisement
●Pitch Bend Change
Status
2nd byte
EnH
llH
n = MIDI channel number
: 0H-FH (ch.1-ch.16)
mm, ll = Pitch Bend value
: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
* Not received when Rx.PITCH BEND = OFF. (Initial value is ON)
* The resulting effect is determined by System Exclusive messages. With the initial
settings the effect is Pitch Bend.
■Channel Mode Messages
●All Sounds Off (Controller number 120)
Status
2nd byte
BnH
78H
n = MIDI channel number
: 0H-FH (ch.1-ch.16)
* When this message is received, all currently-sounding notes on the corresponding
channel will be turned off immediately.
●Reset All Controllers (Controller number 121)
Status
2nd byte
BnH
79H
n = MIDI channel number
: 0H-FH (ch.1-ch.16)
* When this message is received, the following controllers will be set to their reset values.
Controller
Pitch Bend Change
Polyphonic Key Pressure
Channel Pressure
Modulation
Expression
Hold 1
Portamento
Sostenuto
Soft
RPN
NRPN
●Local Control(Controller number 122)
Status
2nd byte
BnH
7AH
n = MIDI channel number
: 0H-FH (ch.1-ch.16)
vv = Control value
: 00H, 7FH (0,127)
00H : Local Off
7FH : Local On
●All Notes Off (Controller number 123)
Status
2nd byte
BnH
7BH
n = MIDI channel number
: 0H-FH (ch.1-ch.16)
* When All Notes Off is received, all notes on the corresponding channel will be turned
off. However if Hold 1 or Sostenuto is ON, the sound will be continued until these are
turned off.
●OMNI OFF (Controller number 124)
Status
2nd byte
BnH
7CH
n = MIDI channel number
: 0H-FH (ch.1-ch.16)
* The same processing will be carried out as when All Notes Off is received.
4
3rd bytes
mmH
3rd bytes
00H
3rd bytes
00H
Reset value
0 (Center)
0 (off)
0 (off)
0 (off)
127 (max)
0 (off)
0 (off)
0 (off)
0 (off)
unset; previously set data will not change
unset; previously set data will not change
3rd bytes
vvH
3rd bytes
00H
3rd bytes
00H
●OMNI ON (Controller number 125)
Status
2nd byte
BnH
7DH
n = MIDI channel number
: 0H-FH (ch.1-ch.16)
* OMNI ON is only recognized as "All notes off"; the Mode doesn't change (OMNI OFF
remains).
●MONO (Controller number 126)
Status
2nd byte
BnH
7EH
n = MIDI channel number
: 0H-FH (ch.1-ch.16)
mm = mono number
: 00H-10H (0-16)
* The same processing will be carried out as when All Sounds Off and All Notes Off is
received, and the corresponding channel will be set to Mode 4 (M = 1) regardless of the
value of "mono number."
●POLY (Controller number 127)
Status
2nd byte
BnH
7FH
n = MIDI channel number
: 0H-FH (ch.1-ch.16)
* The same processing will be carried out as when All Sounds Off and All Notes Off is
received, and the corresponding channel will be set to Mode 3.
■System Realtime Message
●Active Sensing
Status
FEH
* When Active Sensing is received, the unit will begin monitoring the intervals of all
further messages. While monitoring, if the interval between messages exceeds 420 ms,
the same processing will be carried out as when All Sounds Off, All Notes Off and Reset
All Controllers are received, and message interval monitoring will be halted.
■System Exclusive Message
Status
Data byte
F0H
iiH, ddH, ......, eeH
F0H
: System Exclusive Message status
ii = ID number
: an ID number (manufacturer ID) to indicate the manufacturer whose
Exclusive message this is. Roland's manufacturer ID is 41H.
ID numbers 7EH and 7FH are extensions of the MIDI standard;
Universal Non-realtime Messages (7EH) and Universal Realtime
Messages (7FH).
dd,...,ee = data
: 00H-7FH (0-127)
F7H
: EOX (End Of Exclusive)
The System Exclusive Messages received by this instrument are; messages related to mode
settings, Universal Realtime System Exclusive messages and Data Set (DT1).
3rd bytes
00H
3rd bytes
mmH
3rd bytes
00H
Status
F7H
Advertisement
Table of Contents
