Table of Contents
Advertisement
●012b: Ring Modulator
This is an effect that applies amplitude modulation (AM) to the input signal, producing bell-
like sounds. You can also change the modulation frequency in response to changes in the
volume of the sound sent into the effect.
No
Parameter
Value
1
Frequency #1
0 - 127
0-127
2
Sens
0 - 127
0-127
3
Polarity
0 - 1
Up, Down
4
Low Gain
0 - 30
-15- +15 dB
5
High Gain
0 - 30
-15- +15 dB
6
Balance #2
0 - 100
D100:0W-
D0:100W
7
Level
0 - 127
0-127
●0125: Tremolo
Cyclically modulates the volume to add tremolo effect to the sound.
No
Parameter
Value
1
Mod Wave
0 - 4
Tri, Sqr, Sin,
Saw1, Saw2
2
Rate Mode
0 - 1
Hz, note
3
Rate #1
1 - 127
0.05-10.00 Hz
4
Rate
0 - 21
note
5
Depth #2
0 - 127
0-127
6
Low Gain
0 - 30
-15- +15 dB
7
High Gain
0 - 30
-15- +15 dB
8
Level
0 - 127
0-127
●0126: Auto Pan
Cyclically modulates the stereo location of the sound.
No
Parameter
Value
1
Mod Wave
0 - 4
Tri, Sqr, Sin,
Saw1, Saw2
2
Rate Mode
0 - 1
Hz, note
3
Rate #1
1 - 127
0.05-10.00 Hz
4
Rate
0 - 21
note
5
Depth #2
0 - 127
0-127
6
Low Gain
0 - 30
-15- +15 dB
7
High Gain
0 - 30
-15- +15 dB
8
Level
0 - 127
0-127
●012c: Slicer
By applying successive cuts to the sound, this effect turns a conventional sound into a
sound that appears to be played as a backing phrase. This is especially effective when
applied to sustain-type sounds.
No
Parameter
Value
1
Rate Mode
0 - 1
Hz, note
2
Rate
1 - 127
0.05-10.00 Hz
3
Rate #1
12 - 21
note
4
Attack
0 - 127
0-127
5
Input Sync Sw
0 - 1
Off, On
6
Input Sync
0 - 127
0-127
Threshold
20
Description
Adjusts the frequency at which
modulation is applied.
Adjusts the amount of frequency
modulation applied.
Determines whether the frequency
modulation moves towards higher
frequencies (Up) or lower
frequencies (Down).
Gain of the low frequency range
Gain of the high frequency range
Volume balance between the direct
sound (D) and the effect sound (W)
Output level
Description
Modulation Wave
Tri: Triangle wave
Sqr: Square wave
Sin: Sine wave
Saw1/2: Sawtooth wave
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of the change (Hz)
Frequency of the change (note)
Depth to which the effect is applied
Gain of the low range
Gain of the high range
Output Level
Description
Modulation Wave
Tri: triangle wave
Sqr: square wave
Sin: sine wave
Saw1/2: sawtooth wave
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of the change (Hz)
Frequency of the change (note)
Depth to which the effect is applied
Gain of the low range
Gain of the high range
Output Level
Description
When this is set to "note," the effect is
synchronized with the tempo.
Rate at which the 16-step sequence
will cycle (Hz)
Rate at which the 16-step sequence
will cycle (note)
Speed at which the level changes
between steps
Specifies whether an input note will
cause the sequence to resume from
the first step of the sequence (ON) or
not (OFF)
Volume at which an input note will
be detected
No
Parameter
Value
7
Mode
0 - 1
Legato, Slash
8
Shuffle #2
0 - 127
0-127
9
Level
0 - 127
0-127
●0130: Compressor
Flattens out high levels and boosts low levels, smoothing out fluctuations in volume.
No
Parameter
Value
1
Attack #2
0 - 127
0-127
2
Threshold #1
0 - 127
0-127
3
Post Gain
0 - 18
0- +18 dB
4
Low Gain
0 - 30
-15- +15 dB
5
High Gain
0 - 30
-15- +15 dB
6
Level
0 - 127
0-127
●0131: Limiter
Compresses signals that exceed a specified volume level, preventing distortion from
occurring.
No
Parameter
Value
1
Release
0 - 127
0-127
2
Threshold #1
0 - 127
0-127
3
Ratio #2
0 - 3
1.5:1, 2:1, 4:1,
100:1
4
Post Gain
0 - 18
0- +18 dB
5
Low Gain
0 - 30
-15- +15 dB
6
High Gain
0 - 30
-15- +15 dB
7
Level
0 - 127
0-127
●0142: Stereo Chorus
This is a stereo chorus. A filter is provided so that you can adjust the timbre of the chorus
sound.
No
Parameter
Value
1
Filter Type
0 - 2
Off, Lpf, Hpf
2
Cutoff Freq
0 - 16
200-8000 Hz
3
Pre Delay
0 - 125
0.0-100.0 ms
4
Rate Mode
0 - 1
Hz, note
5
Rate #1
1 - 127
0.05-10.00 Hz
6
Rate
0 - 21
note
7
Depth #2
0 - 127
0-127
8
Phase
0 - 90
0-180 deg
9
Low Gain
0 - 30
-15- +15 dB
10
High Gain
0 - 30
-15- +15 dB
11
Balance
0 - 100
D100:0W-
D0:100W
12
Level
0 - 127
0-127
Description
Sets the manner in which the volume
changes as one step progresses to the
next.
Legato: The change in volume from
one step's level to the next remains
unaltered. If the level of a following
step is the same as the one preceding
it, there is no change in volume.
Slash: The level is momentarily set
to 0 before progressing to the level of
the next step. This change in volume
occurs even if the level of the
following step is the same as the
preceding step.
Timing of volume changes for even-
numbered steps (step 2, step 4, step
6...).
The higher the value, the later the
beat progresses.
Output level
Description
Sets the speed at which compression
starts
Adjusts the volume at which
compression begins
Adjusts the output gain.
Gain of the low frequency range
Gain of the high frequency range
Output level
Description
Adjusts the time after the signal
volume falls below the Threshold
Level until compression is no longer
applied.
Adjusts the volume at which
compression begins
Compression ratio
Adjusts the output gain.
Gain of the low frequency range
Gain of the high frequency range
Output level
Description
Type of filter
Off: No filter is used
Lpf: Cuts the frequency range above
the Cutoff Freq
Hpf: Cuts the frequency range below
the Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from the
direct sound until the chorus sound
is heard.
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of modulation (Hz)
Frequency of modulation (note)
Depth of modulation
Spatial spread of the sound
Gain of the low range
Gain of the high range
Volume balance between the direct
sound (D) and the chorus sound (W)
Output Level
Advertisement
Table of Contents
