Table of Contents
Advertisement
5. EFX Type Table
0100: Equalizer
0101: Spectrum
0102: Enhancer
0104: Isolator
0105: Low Boost
0106: High Pass Filter
0110: Overdrive
0111: Distortion
0112: Overdrive2
0113: Distortion2
0107: Speaker Simulator
0114: Amp Simulator(Guitar Amp Simulator)
0120: Phaser
0129: Multi Stage Phaser
012a: Infinite Phaser
0123: Stereo Flanger
0127: 3D Flanger
0128: 2Band Flanger
0121: Auto Wah
0103: Humanizer
012b: Ring Modulator
0125: Tremolo
0126: Auto Pan
012c: Slicer
0130: Compressor
0131: Limiter
0142: Stereo Chorus
0140: Hexa Chorus
0141: Tremolo Chorus
0143: Space D
0144: 3D Chorus
0145: 2Band Chorus
0122: Rotary
012d: Rotary2
0300: Rotary Multi
015b: Stereo Delay1
015c: Stereo Delay2
015d: Stereo Delay3
015e: Stereo Delay4
015f: Stereo Delay5
0150: Monaural Delay
0151: Modulation Delay
0152: Triple Tap Delay
0157: 3D Delay
0159: Tape Echo
015a: Reverse Delay
0172: Lo-Fi
0175: Telephone
0156: Gate Reverb
0200: OD→Chorus(Overdrive→Chorus)
0201: OD→Flanger(Overdrive→Flanger)
0202: Overdrive→Delay
0203: Dist.→Chorus(Distortion→Chorus)
0204: Dist.→Flanger(Distortion→Flanger)
0205: Dist.→Delay(Distortion→Delay)
0206: Enhancer→Cho(Enhancer→Chorus)
0207: Enhancer→Fl.(Enhancer→Flanger)
0208: Enhancer→Delay
0209: Chorus→Delay
020a: Flanger→Delay
020b: Chorus→Flanger
0040: Damper Resonance
16
■EFX Parameter Map
The parameters with "#1" or "#2" at the end of parameter name can be controlled with each
exclusive message "PART EFX CONTROL 1" and "PART EFX CONTROL 2."
●0100: Equalizer
This is a four-band stereo equalizer (low, mid x 2, high).
No
Parameter
Value
1
Low Freq
0 - 1
200, 400 Hz
2
Low Gain #1
0 - 30
-15- +15 dB
3
Mid1 Freq
0 - 16
200-8000 Hz
4
Mid1 Gain
0 - 30
-15- +15 dB
5
Mid1 Q
0 - 4
0.5, 1.0, 2.0,
4.0, 8.0
6
Mid2 Freq
0 - 16
200-8000 Hz
7
Mid2 Gain
0 - 30
-15- +15 dB
8
Mid2 Q
0 - 4
0.5, 1.0, 2.0,
4.0, 8.0
9
High Freq
0 - 2
2000, 4000,
8000 Hz
10
High Gain #2
0 - 30
-15- +15 dB
11
Level
0 - 127
0-127
●0101: Spectrum
This is a stereo spectrum. Spectrum is a type of filter which modifies the timbre by boosting
or cutting the level at specific frequencies.
No
Parameter
Value
1
Band1 (250Hz)
0 - 30
-15- +15 dB
2
Band2 (500Hz)
0 - 30
#1
3
Band3
0 - 30
(1000Hz)
4
Band4
0 - 30
(1250Hz) #2
5
Band5
0 - 30
(2000Hz)
6
Band6
0 - 30
(3150Hz)
7
Band7
0 - 30
(4000Hz)
8
Band8
0 - 30
(8000Hz)
9
Q
0 - 4
0.5, 1.0, 2.0,
4.0, 8.0
10
Level
0 - 127
0-127
●0102: Enhancer
Controls the overtone structure of the high frequencies, adding sparkle and tightness to the
sound.
No
Parameter
Value
1
Sens #1
0 - 127
0-127
2
Mix #2
0 - 127
0-127
3
Low Gain
0 - 30
-15- +15 dB
4
High Gain
0 - 30
-15- +15 dB
5
Level
0 - 127
0-127
●0104: Isolator
This is an equalizer which cuts the volume greatly, allowing you to add a special effect to
the sound by cutting the volume in varying ranges.
No
Parameter
Value
1
Boost/Cut Low
0 - 64
-60- +4 dB
2
Boost/Cut Mid
0 - 64
#1
3
Boost/Cut
0 - 64
High #2
4
Anti Phase Low
0 - 1
Off, On
Sw
5
Anti Phase Low
0 - 127
0-127
Level
Description
Frequency of the low range
Gain of the low range
Frequency of the middle range 1
Gain of the middle range 1
Width of the middle range 1
Set a higher value for Q to narrow the
range to be affected.
Frequency of the middle range 2
Gain of the middle range 2
Width of the middle range 2
Set a higher value for Q to narrow the
range to be affected.
Frequency of the high range
Gain of the high range
Output Level
Description
Gain of each frequency band
Simultaneously adjusts the width of
the adjusted ranges for all the
frequency bands.
Output Level
Description
Sensitivity of the enhancer
Level of the overtones generated by
the enhancer
Gain of the low range
Gain of the high range
Output Level
Description
These boost and cut each of the High,
Middle, and Low frequency ranges.
At -60 dB, the sound becomes
inaudible. 0 dB is equivalent to the
input level of the sound.
Turns the Anti-Phase function on
and off for the Low frequency ranges.
When turned on, the counter-
channel of stereo sound is inverted
and added to the signal.
Adjusts the level settings for the Low
frequency ranges.
Adjusting this level for certain
frequencies allows you to lend
emphasis to specific parts. (This is
effective only for stereo source.)
Advertisement
Table of Contents
