Page 1
Cordless Driver Drill Equipped with Electric Brake 10 mm (318") MODEL 6093D 10 mm (318") MODEL 6093DW With Fast Charger INSTRUCTION MANUAL SPECIFICATIONS • Model 6093D Capacities No load speed Dimensions (LxWxH) weight Steer Wood Wood screw Machine screw High...
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- PRECAUTIONS SHOULD ALWAYS BE FOLLOWED REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
Page 3
14. REMOVE A DJUSTING KEYS ANDWRENCHES. Formhabitof checking to seethatkeys andadjusting wrenches areremoved f romtoolbefore turning it on. 15. AVOID UNINTENTIONAL STARTING. Don'tcarryplugged-in t oolwith finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS.
(11 battery charger, (21 battery, and (31 product using battery. 3. CAUTION -- To reduce risk of injury, charge only MAKITA Battery 7000, 9000 or 9100. Other types of batteries may burst causing personal injury and damage.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C 150°FD or ABOVE 40°C (104°F|. 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3.
Page 6
Installing or removing battery cartridge • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, pull out the set plate on the tool and grasp both Set plate sides of the cartridge while withdrawing it from the barrel.
Page 7
• If youwish to charge twobattery c artridges, allow 15minutes between chargings onthe fast c harger. Installing or removing drill bit or driver bit CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit.
Page 8
Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. Trigger switch CAUTION Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns...
Page 9
Adjusting fastening torque Adjusting ring The fastening torque can be adjusted in six Pointer stages by turning the adjusting ring so that the pointer on the adjusting ring points to a number on the tool body. The fastening torque is minimum when the pointer points to the number 1 and maximum when it points to the -,_,= marking.
Page 10
NOTE • Use the proper bit for the head of the screw that you wish to use. • Make sure that the driver is inserted straight in the screw head, or the screw and/or bit may be damaged. • When driving wood screws, predrill...
Page 11
To recycle a battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location.
SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed Makita Authorized or Factory Service Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from you r Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION These accessories or attachments...
Page 14
Dec. 10 mm (3/8"') CORDLESS DRIVER DRILL Model 6093D ® Note: The switch and other part configurations may differ from country to country.
Page 15
MODEL 6093D Dec -25-'86 ITEM ITEM DESCRIPTION DESCRIPTION USED USED MACHINE MACHINE Pan Head Screw M4x22 (With Washer} Fiat Washer Pan Head Screw M4x35 (With Washe,} Ball Bearlrtg 626LLB Flat Washer Housing Se_ _Wr_h Item Spu_ Gea_ 89 Guide Plale S_eel Ball 48 Cam P_ate Clutch...
Page 16
MAKITA LIMITEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is waxrantad be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.