Table of Contents
Advertisement
Cordless Driver Drill
Capacities
Steel
Wood
Wood screw
Machine screw
10
mm
18 mm
5.5 mm
x
55 mm
6 m m
1318")
I 1
Jj16"l
17/32"
x
2-1j8"l
115164")
Equipped with Electric Brake
10
mm
(3/8") MODEL 60930
10
mm
(3/8") MODEL 6093DW
Dimensions
Net
IL
x W x
HI
2 6 5
mm
x
58 mm
x 2 6 2
mm
No load speed
weight
1.7 kg
High
Low
0
~
1,100
0
- 400
Rimin.
Rimin.
110-318"
x
2-114'
x
10-5/16")
13.7 lbsl
With Fast Charger
INSTRUCTION MANUAL
I
I
SPEC IF I CAT1 0 N S
Model 6093D
Dimensions
Net
I
I L x W x H I
I
weisht
A . C . only
D.C
1
145 mm
x
80 mm x 63 mm
0.8 kg
9 6 v
I
Hr'
I
5 0 H z - 60Hz
I
7 . 2 V - 9.6 V
15-314'
x
3-118"
x 2 - 1 1 2 " )
1
11.8 lbsl
*
Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country to country.
Advertisement
Table of Contents
Related Manuals for Makita 6093D
Summary of Contents for Makita 6093D
- Page 1 Cordless Driver Drill Equipped with Electric Brake (3/8") MODEL 60930 (3/8") MODEL 6093DW With Fast Charger INSTRUCTION MANUAL SPEC IF I CAT1 0 N S Model 6093D Capacities No load speed Dimensions weight x W x Steel Wood Wood screw...
- Page 2 IMPORTANT SAFETY IN STRU CTlO N S (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN.
- Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16.
- Page 4 2. Before using battery charger, read all instructions and cautionary markings o n (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION To reduce risk of injury, charge only MAKITA Battery 7000, 9000 or 9100. Other types of batteries may burst causing personal injury and damage.
- Page 5 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 1 0 ° C (5OOF) ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.
- Page 6 Installing or removing battery cartridge tool before insertion or removal of the battery cartridge. *Always switch off the .To remove the battery cartridge, pull out the set plate on t h e tool and grasp both sides of the cartridge while withdrawing it from the barrel.
- Page 7 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Installing or removing drill bit or driver bit CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing removing the bit.
- Page 8 Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger t o stop. CAUTION : Before inserting the battery cartridge into the tool, always check to see t h a t the trigger switch actuates properly and returns t o the "OFF"...
- Page 9 Adjusting fastening torque The fastening torque can be adjusted in six Adjusting ring - - 7 i stages by turning the adjusting ring so that the pointer on the adjusting ring points to a number on the tool body. The fastening torque is minimum when the pointer points to the number 1 and maximum when it points to the...
- Page 10 NOTE : Use the proper bit for the head of the screw that you wish to use. Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. When driving wood screws, predrill Pilot Nominal diameter of Recommended size holes to make driving easier and to pre-...
- Page 11 Take the battery Makita Authorized Center as a Makita Distributor that been designated battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under "Tools Electric. "...
- Page 12 Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
- Page 13 OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : attachments are recommended for use with your Makita tool specified in this These accessories manual.
- Page 14 25-'86 EN 10 mm (318") CORDLESS DRIVER DRILL Model 6 0 9 3 D Note: The switch and other part configurations may differ from country to country.
- Page 15 6093D Dec -25-'86 MODEL ' i \ M ' i \M DESCRIPTION DESCRIPTION Washer 1 4 Pan Head Screw M 4 x 2 2 lWllh Washer] Flat Ball Bearing 626LLB Head Screw M 4 x 3 5 IWtth Washer1 Flat Washer...
- Page 16 MAKITA LIMED O N E YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted t o ONE YEAR be free of defects from workmanship and materials for the period of...