Options; End Of Cycle Signal - Maytag BRAVOS MGD6600TQ0 Use & Care Manual

To use a Sensor Dry Cycle
• Press POWER.
• Turn the knob to desired Sensor Dry Cycle.
• Select DRYNESS to adjust how dry you want the load. As the cycle runs, the control
senses the dryness of the load and adjusts the time automatically for the selected
dryness level.
The default dryness setting is Normal when a Sensor Dry Cycle is selected. You can
select a different dryness level, depending on your load, by pressing [Dryness and
choosing More, less or [)amp. Selecting More, Less or Damp automatically adjusts
the sensed time needed. Once a dryness level is set, it cannot be changed without
stopping the cycle.
• Select the desired Options.
To make changes during a Sensor Dry Cycle:
• Press PAUSE/CANCEL
• Adjust Dryness.
• MORE
•nORMAL
• LESS
DRYNESS
NOTE: [Dryness selections can be made only while using Sensor Dry Cycles.
How the Sensi-Care
TM
Drying System Works
Moisture-sensing strips and temperature sensors inside the dryer drum monitor how fast
the load is drying, how hot the air should be and when clothes are dry. ]he system
automatically stops the cycle to help save time and avoid overdrying.
To use a Timed Cycle
• Turn knob to desired Timed Cycle.
• Press the TIMED CYC[.E ADJUST up or down arrows until the desired drying time is
displayed. Press the up or down arrows and the time will change by 1-minute
intervals. Press and hold the up or down arrows and the time will change by 5-minute
intervals.
NOTE: The Timed Cycle Adjust features can be used only with Timed Cycles and the
Custom Refresh cycle.
TIMED CYCLE
ADJUST
5,
6.
7,
Press TEMP until the desired temperature illuminates.
• HIGH
• MEDIUM
• LOW
• EX'RA _ow
FI UFF
TEMP
AD;Ugl HMO
cYC _s
NOTE: ]he ]emp feature can be used only with Timed Cycles and the Custom Refresh
cycle.
NOTE: During a Timed Cycle, you can change the settings for Time, Temp, the Wrinkle
Prevent setting and the End of Cycle Signal.
(OPTIONAL STEP) If desired, select OPTIONS. For more details, see "Options."
(OPTIONAl. STEP) [f desired, press END OF CYCI.E SIGNAl.. A signal will sound to alert
you when a cycle ends. For more details, see "End of Cycle Signal."
Press STARE Be sure the door is closed.
• If you do not press Start within 5 minutes of selecting the cycle, the dryer
automatically shuts off.
• If you wish to end your drying cycle after pressing Start, press PAUSE/CANCEL twice.
To use a Steam Cycle
• Press POWER.
Turn the knob to desired Steam Cycle.
Press the TIMED CYCLE ADIUST up or down arrows until the desired drying time is
displayed. Press the up or down arrows and the time will change by 1-minute
intervals. Press and hold the up or down arrows and the time will change by 5-minute
intervals.
NOTE: The Timed Cycle Adjust features can be used only with Timed Cycles and the
Custom Refresh cycle.
TIMED CYCLE
ADJUST
Press TEMP until the desired temperature illuminates.
• MKDIUM
• kow
• EXTRA LOW
FLUFF
TEMP
C¥C S
NOTE: The R_mp feature can be used only with Timed Cycles and the Custom Refresh
cycle.
NOTE: During the Custom Refresh cycle, you can change the settings for Timed Cycle
Adjust and Temp Adjust. Open the door or press PAUSE/CANCEL once to pause the cycle,
or press PAUSE/CANCEl. twice to cancel a cycle.
18