Manual Mode Setting; Play Option - Boss GT-10 Owner's Manual

Chapter 8 Parameters Guide

MANUAL MODE SETTING

Parameter/ Explanation
Range
Number Pedal 1–4, BANK▼Pedal, BANK▲Pedal
The Number pedal and the BANK pedal are used for
switching specified effects on and off.
Off The function is not assign to the pedals.
Ch.A/B Switches between Preamp channel A and B.
OD Sol Switches the OD/DS SOLO on and off.
Solo Switches the Preamp SOLO on and off.
Switches the preamp SOLO, for both
channel A and B, on and off.
A&BSol
If one of the two channels is off, both will
be turned on.
Comp Switches the COMP on and off.
OD/DS Switches the OD/DS on and off.
Switches the PREAMP/SPEAKER on and
Preamp
off.
EQ Switches the EQ on and off.
FX1 Switches the FX-1 on and off.
FX2 Switches the FX-2 on and off.
Delay Switches the DELAY on and off.
Chorus Switches the CHORUS on and off.
Reverb Switches the REVERB on and off.
PdlFX Switches the Pedal FX on and off.
S/R Switches the SEND/RETURN on and off.
AmpCtl Switches the Amp Control on and off.
Tuner Switches the TUNER/BYPASS on and off.
PL Switches the PHRASE LOOP on and off.
PL R/P Records/plays back the phrase.
PL Clr Clears the phrase.
PL M/P Mutes playback of the phrase.
BPMTap Used for tap input of the Master BPM.
DlyTap Used for tap input of the delay time.
Controls the Start/Stop of external MIDI
MIDI
devices (such as sequencers).
Controls the Play/Stop of external MIDI
MMCPly
devices (such as hard disk recorders).
Increases the patch volume level by 10
Lev+10
units.
Increases the patch volume level by 20
Lev+20
units.
Decreases the patch volume level by 10
Lev-10
units.
Decreases the patch volume level by 20
Lev-20
units.
Switches to the next higher patch number
NumInc in the same bank as the currently selected
patch.
Switches to the next lower patch number
NumDec in the same bank as the currently selected
patch.
BnkInc Switches to the next higher bank number.
BnkDec Switches to the next lower bank number.
136

PLAY OPTION

Parameter/ Explanation
Range
Preamp Mode
The patch preamp setting is used. This al-
Patch lows you to use different preamp settings
in each individual patch.
The system's preamp setting is used. This
System1–3 applies the same preamp settings to all
patches.
Patch ChgMode (Patch Change Mode)
This setting determines whether or not the decay of reverb, delay,
and similar effects continue when patches are switched on the GT-
10.
Patches are changed normally. The unit
switches to the subsequent patch without
Fast
any carry-over of the decay from the pre-
vious patch's reverb or delay.
The unit switches to the subsequent patch
with the decay from the previous patch's
reverb or delay continued after the switch
is made.
Smooth
To ensure smooth switching, the patches may
be switched with a delay of one tempo beat.
Bank Chg Mode
This sets the timing with which the GT-10 switches to the next
patch when switching banks with the pedals.
Although the indication in the display is
updated to reflect the change in the bank
Wait when a BANK pedal is pressed, the patch
will not change until a number pedal has
been pressed.
The patch switches instantly when a
Immed BANK pedal or any of the number pedals
is pressed.
BankExtentMin (Bank Extent Minimum)
P01–P50,
Sets the lower limit for the banks.
U01–U50
BankExtentMax (Bank Extent Maximum)
P01–P50,
Sets the upper limit for the banks.
U01–U50
EXP Pdl Hold (Expression Pedal Hold)
This setting determines whether or not the Assign's (p. 50) opera-
tional status is carried over to the next patch when patches are
switched.
The Assign's operational status is not car-
ried over.
(Example)
If a patch is switched while the volume is
being controlled with an EXP Pedal, the
Off
volume of the subsequent patch is set to
the value set in that patch.
If the EXP Pedal is operated, the volume
will change in accord with the pedal's
movement.