Table of Contents
Advertisement
REMOTE
CONTROL
Z-TRAK
3. Point the Z-Trak remote towards your VCR. Press
CHAN UP followed
by POWER.
If your VCR did
not turn off, keep repeating
CHAN UP followed
by
POWER
until the VCR responds.
4. If your VCR turned off, press ENTER to save the
code. The VCR button will flash three times after
ENTER is pressed.
5. Now try other controls
on your VCR, such as Play,
Rewind,
etc., to make sure that the correct VCR
brand code number
was selected.
(If not, repeat
steps 2 to 4.)
6. The MUTE key can be pressed at any time to cancel
AutoFind
mode.
The original
VCR brand code will
remain unchanged.
7, The remote will exit AutoFind
mode automatically
after 60 seconds
if no key press or trackball
move-
ment is detected.
NOTE:
•
To view the code that was programmed,
perform
Steps 2 and 3 of "Programming
Your Z-Trak
Remote."
VCR CODES
BY BRAND
NAME
Admiral
Adventura
Aiwa
Akai
Audio
Dynamics
Bell & Howell
Broksonic
Canon
Citizen
Craig
Curtis Mathes
Dacwoo
Daytron
DBX
Emerson
Fisher
Funai
General
Electric
Coldatar
Go Video
Hitachi
Instant Replay
J.C. Penney
JVC
Kenwood
Logik
LXI
Magnavox
Maratttz
Marta
, Memorcx
Mitsubishi
VCRS
208, 261
231
231
223. 238, 241
202, 218
206,247
221.226,250,255
214
209
212
214,259
244,246,248,254
236,246
202,218
203.221,223,226,
233,235.243,250
211,212,213,247
231
214,216.220
209
256.262,263
215,257
214,227
214,215,218,227
202,225,258
2O2
239
209, 231
207. 214, 231
207, 218
209
206,212,214,231
204,222,252,264
Montgomery
Ward
Multi Tech
NEC
Orion
Panasonic
Pentax
Philco
Philips
Pion_r
Portland
Pro Scan
Quasar
RCA
Realistic
Samstmg
Sansui
Sanyo
Scott
Sears
Shalp
Shintom
Signature2000
Sony
Sylvania
Symphonic
Tashiko
Tatung
Teac
Tcknika
Toshiba
Vector Research
Yamaha
Zenith
XRI000
208, 214, 216, 219,
231,249
239
202. 218
250
214,251,259
215
207.214
207,214,227
210,215
246
2 t6, 260
214. 259
215.216,220,227,240.
242,260
206,208,212.214,231
220,230
239
206,212,247
204,205.233,243
206,209,2-I I,212.215
208,261
239
20_,214,216.219,
23I,249
217,232.237
207,214,227
231
12O9
202
202,231
234
205.215
204, 218
202,218
201.224.225,229,237
239
CLEANING
THE TRACKBALL
To keep the Z-Trak remote functioning properly, it is necessary to occasionally clean the TRACKBALL device. To do this:
1, Use a solution
of mild dish washing detergent
and water.
2, Moisten
a clean soft cloth with the solution and lay the cloth flat on a table.
3. Turn the Z-Trak remote upside down and gently roll the TRACKBALL
on the cloth.
4.
Allow the remote to air-dry before using it again.
CAUTION:
•
DO NOT USE ALCOHOL
OR OTHER CLEANING
FLUIDS TO CLEAN THE TRACKBALL
AS THESE MAY
DAMAGE
THE REMOTE.
2923-01-O
11 -- 4
Advertisement
Table of Contents
