GE Monogram ZBD6400 Owner's Manual page 13

Control Panel/Operation -- ZBD6700 & ZBD6900
l) is hw as h¢r
3. SMART DRY--
4. WATER TEMP--
NORMAL
HIGH
SANI
When selected, sensors detect the presence of rinse aid and the final rinse
temperature. The drying heater and tan are then turned on for the minimmn
time to achieve optimmn drying results. This saves energy as compared to
conventional heated dry and saves time as compared to non-heated dry.
SMART DRY is not
avaiiable
on RINSE ONI,¥.
This button proxides extra heat options to increase water temperature for
optimmn perfimnance.
This is the default setting--proxides a wash and rinse with water temperatm'es
3 o_ 50 _
up to l, 1 F (55°(2) in the NORMAl, cycle and 14: F (63°(;) in POTS &
EA_NS.
This water temp selection proxides a wash and rinse with water temperatm'es
350 5 -o_
5-0
up to 1, _ F (: i C) in the NOPdX4AI, cycle and 1::9 F (68°C) in POTS &
EkNS. Use this option
for heaxilv
soiled dishes. Cannot be used with RINSE
()NIX or CHINA CRYSTAl,.
This water temp selection provides a sanitizing wash and rinse with water
temperatures up to 160°F (71°C) in the NORMAl, cycle and 171 °F (77°C) in
POTS & PANS. Cannot be used with RINSE ONlY or CHINA CRYSTAl, At
the end of the X,\;_tSH cycle, the SANI OPTION light will remain illmninated
to indicate that the sanitization conditions have been met.
NSF INTERNATIONAL
Meets NSF Standard 184 Sanitization and Cleaning performance
of household spray-type dishwashers.
NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.
5. DELAY START--This option will allow Um to dela) the start time of any wash c)cle except
RINSE ONLY for up to 6 horn's.
• Select the delax start time you want by pressing, the DEI,AY START button. Multii)le I)ressin'*'
will alternate the delay time between 2, 4 or 6 horn's and OFF.
Start a
wash load
To start the dishwasher, close the door tmtil it locks in place. The last used cxcle will be displayed. To
begin this cycle push the START button. To select a different cycle, push the desired Cycle Selection
and Option buttons, and then press the START button.
The door must be closed and latched into place to select a cxcle or an option.
To interrupt/pause a cycle, press the selected cycle button. The Stntus Indicators will flash.
CAUTION: Be careflfl when opening the door; the hot steam that escapes when the door is
opened mav cause ii_jm'ies. Stand back as you open the door and allow the steam
to escape.
_ATTENTION : Faites attention h)rsque xous omrez la porte, i,a xapeur br0lante qui s'_chai)pe
lorsque wins ouwez la porte pendant un programme de lavage peut causer des
b_ film'es. I,orsque vous ouw'ez la porte, reculez et laissez la wq)em" s'_chapper
de l'appareil.
To restart the wash process, close the door tmtil it locks in place. Re-press the cxcle button. There
max be a time delay of up to a tew minutes, because the temperatm'e inside the dishwasher needs
to stabilize before it restarts the wash cxcle. Dm'ing this time the SENSING light will be on.
To cmacel the cycle after it has started, press and hold the START/CANCEl, button fin" 3 seconds.
The dishwasher will then drain and the cycle indicator lights will flash. At this point a new wash
cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out atter
the dishwasher drains. If w)u have selected a new wash cycle, remember to add more detergent
to the detergent compar(ment if required.
13