Page 1
COLOUR VIDEO COPY PROCESSOR MODEL CP700E OPERATION MANUAL CP700 MONITOR MEMORY PRINT POWER OPEN REMOTE THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR COLOUR VIDEO COPY PROCESSOR. This video copy processor complies with the requirements of the EC Directive 89/336/EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC.
2. Precautions In the interest of safety, please observe the following precautions: POWER REQUIREMENT This Colour Video Copy Processor is designed for operation on 220-240V, 50Hz AC. Never connect to any outlet or power supply having a different voltage or frequency. WARNING: THIS APPARATUS MUST BE EARTHED.
Page 4
2. Precautions BE CAREFUL WITH THE PRINTING UNIT Don't move the unit while the printing unit is sliding out. This may cause injury. Be careful not to catch your finger in the printing unit while the printing unit is being retracted into the unit. CONNECTION CABLES Use the provided power cord and the composite video signal cable.
Page 5
2. Precautions CAUTION ON RELOCATING When transporting this unit, make sure it is not likely to be subjected to impacts. They can be a prime cause for damage. Further, make sure to disconnect the power cord from the power outlet, and the cables from the connected devices. SAFETY CHECKS Periods: According to the recommendations of the manufacturer of the medical device.
3. Preparations before operation 1 Removing the fixed screw on the printing unit and protective cushion Pages 5 - 6 2 Installing the lithium battery Page 6 ,Power for memorizing the day and present time are supplied by a lithium battery. Before using this unit install the lithium battery.
Page 7
3. Preparations before operation 1 Remove the protective cushion. Note: Unplug the power cord from outlet for safety. 1 Press the OPEN button on the front panel. Printing unit will slide out. Attention} , Do not touch the thermal head. Fingerprints or dust on the thermal head will degrade the print quality.
Page 8
3. Preparations before operation 3 Installing print paper and ink sheet 1 Installation procedure of print paper 1 Move the knob on the printing unit to the direction indicated by the arrow. 2 Insert the print paper in the position as shown below. Place the gear to the right side.
Page 9
3. Preparations before operation 1 Install the ink sheet Install the ink sheet to the ink cassette before installing the sheet cassette to the unit. White roller 1 Set the black roller of the ink sheet to ink cassette as shown right A, B. 2 Set the thin stick of white roller to the ink cassette as shown right C.
Page 10
3. Preparations before operation 1 Print paper and ink sheet Attention} , The following types of paper sheet sets are available. Use our original consumable. We can not guarantee the failure of using others. Ink sheet Product name Ink sheet size Number of prints Usage PK700S...
Page 11
3. Preparations before operation Menu display When setting the day and present time , use the menu on the LCD display. Also use the menu when selecting each setting after connecting an external device or selecting the print size (S /L). , There are 2 menus, Main menu and Memory SW menu.
Page 12
3. Preparations before operation 4 Setting the present time 1 Setting the day and present time Set the day and present time on the lower part of the print by the following procedure. , Set the day and present time in the menu on the monitor display or LCD display.
Page 13
3. Preparations before operation 5 Press the UP button or DOWN button to change the value. T i m e A d j M e n u M O N T H : 0 8 6 Press the RIGHT button. The month is set and display the “YEAR”. T i m e A d j M e n u Y E A R : , The “YEAR”...
Page 14
3. Preparations before operation E Press the SET button. T i m e A d j M e n u , When pressing the SET button, the present time function will S E C O N D : be started. F Press the SET button.
4. Connection with external equipment The functions of this unit can be set with the menu screens displayed on the monitor. 1 Connection with Monitors Pages 14 - 16 Explains how to connect with a monitor. Explains the setting of sync. polarity. , When the sync.
Page 16
4. Connection with external equipment (Monitor) Setting the sync. polarity and output sync. signal When the sync. polarity or sync. signal of a monitor to be connected is not adjusted to the initial setting of this unit, the image may not be displayed correctly. In this case, adjust the sync. polarity and sync. signal output to the monitor. When the image is displayed correctly, the setting is not required.
Page 17
4. Connection with external equipment (Monitor) Setting the output sync. signal “OUTPUT SYNC” 5 Press the DOWN or UP button to select “OUT SYNC”. S i g n a l A d j M e n u , The set level of the sync. signal, for example, “0.3V” is displayed. O U T S Y N C : T T L Set the sync.
Page 18
4. Connection with external equipment (VIDEO/S-VIDEO) 2 Connection with VIDEO signal, S-VIDEO (Y/C separate VIDEO) signal equipment When connecting the unit with another equipment, make sure to set the power of each equipment to “OFF”. VIDEO signal To VIDEO IN terminal VIDEO ( RS-232C REMOTE...
Page 19
4. Connection with external equipment (RGB Analog signal) 3 Connection with RGB Analog Signal equipment , When connecting the unit with another equipment, make sure to set the power of each equipment to “OFF”. RGB Analog signal equipment To RGB Analog IN SCAN START terminal ( RECORD...
Page 20
4. Connection with external equipment (RS-232C Interface) 4 Connection with RS-232C equipment , When connecting the unit with another equipment, make sure to set the power of each equipment to “OFF”. To RS-232C port (RS-232C) To RS-232C port RS-232C REMOTE VIDEO S-VIDEO AC LINE...
Page 21
4. Connection with external equipment (RS-232C Interface) Setting BAUD RATE 1 Press the DOWN or UP shift buttons to select “BAUD RATE”. S y s t e m S e t M e n u B A U D R A T E : 9 6 0 0 The set baud rate, for example, “9600”...
Page 22
4. Connection with external equipment (RS-232C Interface) 4 Press the SET button. , “CHANGE : OK” is selected. 5 Select “OK”, then, press the SET button. , The source image (input signal from the equipment connected) is displayed. 0 The setting of COMMAND TYPE is completed. RS-232C DATA SIGNAL RS-232C input connector port signal allocation Pin No.
5. Features and functions 1 FRONT PANEL pages 22 - 23 Explains the buttons and terminals, etc. on the front panel. 2 INSIDE OF PRINTING UNIT page 23 Explains the installation of the ink cassette, print paper and battery inside the unit. 3 REAR PANEL page 24 Explains input/output terminals on the rear panel.
Page 24
5. Features and Functions 6 Memory button [MEMORY] This enables memorization of the image to be printed. 7 Print button [PRINT] Press this button to print the images memorized by the MEMORY button. A green lamp will light during printing. The screen switches to the picture of the input signal.
Page 25
5. Features and Functions 3 REAR PANEL RS-232C REMOTE VIDEO S-VIDEO AC LINE IMPEDANCE Potential equalization connector G/G+SYNC H+V-SYNC This is used to equalize the potential of the equipment HIGH connected to the unit. SYNC. For details, refer to the installation instruction of the equipment to be connected.
Page 26
5. Features and Functions 4 REMOTE CONTROL DISPLAY COLOR FIELD PROG. ADJUST /FRAME PRINT Q' ty MENU CLEAR STOP MEMORY MONITOR PAGE MEMORY PRINT 1 COLOR IMAGE ADJUSTMENT button [COLOR ADJUST] When this button is pressed, a screen for adjusting the video image is displayed. Use this button to set the various functions of this unit.
5. Features and Functions 8 PRINT button [PRINT] Press this button to print the image memorized by the MEMORY button. The image on the monitor screen is switched to the picture of the input signal. 9 PROGRAM button [PROG.] Press this button to select the images memorized in the program of this unit and various settings such as printing. Each time this button is pressed, the program is switched.
6. Printing procedures (Basic prints) One picture image can be printed on one sheet. { S size printing { L size printing 1 Printing Pages 28 - 34 Explains storing an image in the memory and printing 2 Continuous printing Pages 35 - 36 Explains the continuous printing of the same image.
6. Printing Procedures (Basic prints) 1 Printing 1 Selecting FIELD or FRAME 1 Press the FIELD/FRAME button on the remote control to select FIELD or FRAME. DISPLAY COLOR FIELD PROG. ADJUST /FRAME FIELD/FRAME button PRINT Q' ty MENU CLEAR STOP , Select the FRAME mode for a high resolution still image printing.
6. Printing Procedures (Basic prints) 1 Selecting input signal , Select “VIDEO” , “S-VIDEO” or “RGB” according to the input signal. , The input signal can be set on the menu screen displayed on the monitor or LCD. , It is not necessary to select the input signal everytime you print unless the input signal is changed. M E N U 1 Press the MENU button.
6. Printing Procedures (Basic prints) 5 Press the SET button . S i g n a l S e t M e n u , “CHANGE : OK” is selected. C H A N G E : O K , When changing the input signal selected at step 4, press the RIGHT button to select “CANCEL”...
6. Printing Procedures (Basic prints) 1 Setting print size (S/L) , Set the print size to “S” or “L” according to the ink sheet installed. , The print size can be set on the menu screen displayed on the monitor or LCD. , It is not necessary to set the size everytime you print unless the size of the ink sheet is changed.
6. Printing Procedures (Basic prints) 5 Press the SET button. P r i n t M e n u C H A N G E : O K , “CHANGE : OK” is selected. , When changing the size setting selected at step 4 , press the RIGHT button to select “CANCEL”...
6. Printing Procedures (Basic prints) 1 MEMORY PAGE The following image memorization function is available since this unit has 2 frames to memorize images. When storing one image in the memory: , In the frame mode, 2 images can be memorized in 2 frames. Image A Image B 1 frame + 1 frame = 2 frames...
6. Printing Procedures (Basic prints) , The page to store an image can be selected by pressing the MEMORY PAGE button. The page being selected is shown in green. , The image will be stored in the selected memory page when pressing the MEMORY button. (when memory page increment is set to OFF) , When pressing the MONITOR button, the image of the memory page being selected is displayed on the monitor.
6. Printing Procedures (Basic prints) 2 Continuous printing The desired number of memorized images can be printed continuously when the desired number is set before printing. The number of prints can be changed during printing. The continuous printing also can be cancelled by setting the number of prints to 1 during printing.
6. Printing Procedures (Basic prints) 1 Changing the number of prints during printing , When changing the number of prints during printing: 1 Press the PRINT Q'ty buttons to set the number of prints to 1. 2 After the image being printed is printed out, press the PRINT Q’ty buttons to change the number of prints.
7. Setting the functions fi fi MAIN MENU is used to open the sub menu. Setting the following with the sub menu. When selecting "SAVE PRG", the setting can be stored. Main Menu PRG. 1.COLOR ADJ : PUSH [ 2.SIGNAL SET : PUSH [ 3.ADDITIONAL : PUSH [ 4.PRINT : PUSH [...
. Making a comment display DISPLAY One of them is indicated. 5.COMMENT MITSUBISHI COLOR VCP CP700E COLOR Source image 0 1 2 3 4 5 6 7 8 9 A B C D E F G H I...
7. Setting the functions Day and present time setting display 1. TIME ADJ 28-02-99 19:45:00 Analog image adjustment display p 57 Button function setting display ANALOG ADJ : 0 -------------------------- 2. KEY SETTING CONT : 0 -------------------------- KEY LOCK : OFF/ON R-SUB : 0 -------------------------- MEM &...
: 1 / 2 / 3 Comment making display MENU Comment Menu CHANGE OK CANCEL CHANGE Comment Menu [MITSUBISHI COLOR ] MENU [VCP CP 700E Fixing the comment System setting display 1 System Menu SIZE : WIDE MIDDLE NARROW USER...
INS : PUSH [SET] MENU DEL : PUSH [SET] CLR : PUSH [SET] Comment Menu Print Set Menu [MITSUBISHI COLOR] M MENU ECHO GAMMA a : X = a : Y = NOPQRSTUVWXYZ b : X = 128 0 1 2 3 4 5 6 7 8 9 ( ) , .
7. Setting the functions 1 Displaying menu screen , All functions are operated with the remote control. 1 Main menu – sub menu display M E N U , Press the MENU button to display Main menu. 2 MEMORY SW MENU – sub menu display , Press the POWER button while pressing MEMORY button to display MEMORY SW menu.
7. Setting the functions 3 Press the SET button. , “CHANGE : OK/CANCEL” is selected. K e y S e t t i n g M e n u C H A N G E : O K , Select "OK" to close the menu. Select "CANCEL" to cancel the setting again by the RIGHT or LEFT button.
7. Setting the functions (Main menu) Function 1 MAIN MENU Open the sub-menu from Memory menu. e.g. Monitor display 1. COLOR ADJ 1 Items and setting displayed are shown below. 1. COLOR ADJ ..Adjust color of printing image 2. SIGNAL SET ..Selecting the input signal, reverse of odd and even field lines, filter,etc. 3.
7. Setting the functions (Main menu) 1 COLOR ADJ Adjusting the color of the image , With this menu, the color of the source image and memorized image can be adjusted. COLOR ADJUST , This menu is also displayed by pressing color ADJUST button.
7. Setting the functions (Main menu) ANALOG ADJ The adjustment image of analog input signal display , This menu is used to adjust the image of analog input signal display before storing in the memory. , This menu is opened when pressing RIGHT button on “ANALOG ADJ : PUSH [ ] ]”...
7. Setting the functions (Main menu) 2 SIGNAL SET Signal selecting menu INPUT Function Select the signal from inputting signal on the rear panel. VIDEO ..Signal from VIDEO input terminal S -VIDEO ..Signal from S-VIDEO input terminal RGB ..... Signal from RGB input terminal FIELD Function The odd even field lines will be reversed depending on the input interlaced signal.
7. Setting the functions (Main menu) 3 ADDITIONAL Special print setting S T R O B E Function This function is to repeat storing the image in the memory according to selected the time interval. When MULTI is set to “ON” , the image is stored in order of image number . When MULTI is set to “OFF”...
Page 50
7. Setting the functions (Main menu) SEPARATE Function Switching the white frame Separate the each image in multi-image print with white frame ON ....White frame print OFF ....Normal print • When “MULTI” is set to “ON”, this function is displayed. 4 PRINT Print setting 1 M O D E...
7. Setting the functions (Main menu) C O M M E N T Function Selecting the comment Selecting the comment on printing from 4 types. OFF ..Comment is not printed. COM ..Printing the made comment C-T ..Printing the made comment and the time and date when the image is stored in memory. The day and time is overlaid on comment.
7. Setting the functions (Main menu) 5 COMMENT Making a comment Function Making a comment on print Refer to pages 53-58 for details. 6 SYSTEM System setting 1 SIZE Function Selecting a print area of printing image Selecting the print size and user print size setting printing size Picture element (S size)
7. Setting the functions (Main menu) C O N V E R T Function This function is to output the selected input signal in the “INPUT SEL” function on “2. SIGNAL SET” menu to the VIDEO/RGB/S-VIDEO output terminal ON ..Output the selected input signal to the VIDEO/RGB/S-VIDEO output terminal OFF ..
7. Setting the functions (Making a comment) TOP/BOTTOM/LEFT/RIGHT Function Setting the print area By adjusting print area, the image size to be printed can be limited. Printing area adjustment can be operated with the setting menu on the screen. TOP ..... Top adjustment (setting area -16 to +134 ) BOTTOM ..
7. Setting the functions (Making a comment) 1 Remote control function on the comment display M E N U ..Selecting 4 blocks on the comment menu Menu button Comment display block Character block Editing mode selecting mode CHANGE : OK/CANCEL , When pressing “MENU”...
7. Setting the functions (Making a comment) 1 Editing command , Selecting each command in editing mode by pressing RIGHT or LEFT shift button. The letter inputting command CAPS (Capital Letters ) ... Capital letters / small letters , When the SET button is pressed after selecting capital or small letter by pressing button, the character block is switched in order of capital letters small letters...
7. Setting the functions (Making a comment) 1 Inputting the letter Selecting comment block M E N U 1 Press the MENU button to select comment display block. , The selected block is displayed in green. SHIFT 2 Press the shift button to select the inputting letter position.
7. Setting the functions (Making a comment) 1 Inserting a space / deleting a character / Clearing the whole comment Insert a space, delete a character or clear the whole comment by the following procedure. (e.g.) In case of deleting “E”. M E N U 1 Press the MENU button to select comment display block.
7. Setting the functions (Making a comment) 1 Close the comment menu M E N U 1 Press the button to select “CHANGE : OK/CANCEL” . , “CHANGE” is displayed in blue. SHIFT 2 Press the shift button to select “OK” . , In case of changing a comment , select the “CANCEL”...
7. Setting the functions (Memory SW menu) SETTING FUNCTIONS 2 MEMORY SW MENU When pressing the POWER button while pressing the MEMORY button on the front panel with the POWER turned off the MEMORY SW MENU is displayed. (e.g.) Monitor display: MEMORY SW MENU KEY SET KEY LOCK...
7. Setting the functions (Memory SW menu) 1 TIME ADJ Setting the day and present time TIME ADJ ( Time Adjust ) Function Setting the day and present time. Refer to pages 11-13 for setting. 2 KEY SET Setting the buttons' function KEY LOCK Function The function on the remote control buttons and all of the buttons of the unit except POWER button are...
7. Setting the functions (Memory SW menu) CLEAR KEY ( Memory and Clear ) Function Setting the CLEAR button function on the remote control. ONE ..Pressing the CLEAR button on the remote control, the memorized image being selected is cleared. ALL ..
7. Setting the functions (Memory SW menu) H -START (H - Position ) Function Adjust the H-position timing for the special signal . NML (Normal) ..Inputting PAL signal FRONT ....Inputting the special signal When the image is imbalanced and cannot be corrected by H-POSI on basic printing, set to “FRONT”. When setting to “FRONT”, the printing image may distorted in the special playback of VCR because “AFC”...
7. Setting the functions (Memory SW menu) MARGIN Function Cut the print paper so that the upper margin is small. ON ..Small margin OFF ..Behind the margin Margin cut This function is convenient when putting the print on prints on records or non-PVC sleeves for print orchiving.
7. Setting the functions (Memory SW menu) 5 SYSTEM System setting 2 PRG ALL INIT ( Program All Initial ) All settings of 3 memory programs to store each function is initialized. ON ..Each setting function is initialized OFF ..Not initialized This function is available when selecting “OK”...
8. Printing procedures (Special prints) The following printing is available. 1 MULTI prints SAME or DIFF ..............Pages 68 - 71 2,2s,4, or 16 images can be printed on a sheet. 1 2/2s-image 1 4-image 1 16-image S-size paper L-size paper S-size paper L-size paper S-size paper L-size paper 2 PHOTO prints PHOTO .................
8. Printing Procedures (Special prints) 1 Memory pages The image size to be memorized is 1216 by 1200 dots. The following functions are available on this unit. The following is an example of S size paper. 1 2-image prints (MULTI prints) , In FRAME mode, 2 images can be memorized on one page.
8. Printing Procedures (Special prints) 1 16-image prints (MULTI prints) , In FRAME mode, 16 images can be memorized on 1 page. example : VIDEO FRAME (Display on the monitor) 16 images on 1 page 1 Image size and the number of memory pages Number of memory pages No.
8. Printing Procedures (Special prints) 1 MULTI PRINTS 2, 2s, 4 or 16 images can be printed on a sheet. , The following prints are available. Setting of S size prints L size prints the No. of images image printing A A A A A A A A A A...
8. Printing Procedures (Special prints) 3 Press the DOWN or UP button to select “MULTI : OFF/ON”. Then, press the RIGHT button to select “ON”. , “MODE : SAME/DIFF/PHOTO” is displayed on the menu screen. , “IMAGES : 2 / 2s/ 4/ 16” is displayed on the lower line. 4 Press the DOWN button to select “MODE : SAME/DIFF/PHOTO”.
8. Printing Procedures (Special prints) 1 Storing images in memory 1 Press the DISPLAY button to display the set conditions. 2 Press the FIELD/FRAME button on the remote control to select FIELD or FRAME. 3 Press the MONITOR button and select the source image (“LIVE” is displayed on the monitor.) to display the image to be stored in memory.
8. Printing Procedures (Special prints) When “MODE” is set to “SAME”, or “MODE” is set to “DIFF” and “IMAGES” to 2(or 2s) , When “MODE” is set to “SAME”, or “MODE : DIFF” and “IMAGES” is set to 2(or 2s), only one image is displayed on the monitor screen.
8. Printing Procedures (Special prints) 2 PHOTO PRINTS PHOTO print is a function to print the images on the photo size (3x4cm, 5x5cm) and card size (2x1.5cm ). , CARD size print is suited to stick on a business card. , The following prints are available.
8. Printing Procedures (Special prints) 1 Selecting the size 1 Press the DOWN button to select “IMAGES : CARD / 3*4 /5*5” menu. 2 Press the RIGHT button to select “CARD” , “3*4” or “5*5”. 1 Displaying the image from input signal (source image) 1 Press the SET button.
8. Printing Procedures (Special prints) 1 Printing the images 1 Press the MONITOR button to display the memorized image. (“MEMORY” is displayed on the monitor.) , A white frame is indicated on the displayed image. , The image within the white frame is photo-printed. PRG.
8. Printing Procedures (Special prints) 1 OPERATION 1 Setting the multi-print and photo-print menus Setting multi-print and photo-print functions 1 Press the MENU button. Then, press the UP or DOWN shift button to select “3. ADDITIONAL PUSH [ ]”. 2 Press the RIGHT shift button to select “3.
8. Printing Procedures (Special prints) B Press the SET button. , The source image (image from the input signal) is displayed. 1 Storing images in memory / Printing the images 1 Store the images to be printed in memory. , Refer to 1 MULTI PRINT or 2 PHOTO PRINT for storing images in memory. 2 Press the PRINT button.
8. Printing Procedures (Special prints) 1 Setting 1-image/multi-image memory 1 When memorizing 1 image in STROBE mode This setting is used to memorize 1 image in memory page [A B] (FRAME) or [A B C D] (FIELD). 1 Set the mode to 1-image. Select “OFF”...
8. Printing Procedures (Special prints) 1 Displaying the source image (image from the input signal) 1 Press the SET button. , “CHANGE : OK/CANCEL” is selected. , When changing the setting, select “CANCEL”. 2 Press the SET button. , The MAIN MENU is displayed. 3 Press the SET button.
8. Printing Procedures (Special prints) 1 Interrupting strobe memory , When any buttons on the remote control except MEMORY button is pressed, the strobe memory is interrupted. 1 Pressing the PRINT button To print the images stored in the strobe memory, follow the following procedures after interrupting the strobe memorization. 1 Display the desired image on the monitor.
8. Printing Procedures (Special prints) 3 Set the “PAGE INC” to “ON”. Set the “PAGE INC : ON/OFF” to “ON” in “6. SYSTEM” from the MAIN MENU. 4 Set the “MEM&PRINT” to “ON”. Set the “MEM&PRINT : OFF/ON” to “ON” in “2. KEY SETTING” from the MEMORY SW MENU. Displaying the source image (image from the input signal) 1 Press the SET button.
8. Printing Procedures (Special prints) External REMOTE 2 terminal on the rear panel The images can be stored in memory and printed by sending the remote signal through the external remote terminal on the rear panel. , Make out the necessary circuit to use this function by referring to the following. Pin No.
8. Printing Procedures (Special prints) 1 Circuit inside the VCP } VCP User side DC5V DTC124EK 2 MEMORY To VCP DC5V 2.2K DTC124EK 4 BUSY From VCP DC5V DTC124EK 5 PRINT To VCP 6 REMOTE To VCP Pin No. 6 REMOTE terminal By sending the following remote control codes from Pin No.
9. Troubleshooting 1 Error messages and countermeasures 1 If for some reason printing is not possible or error occurs during printing, the error message will be displayed on the monitor screen or LCD. In this case, follow the procedure described below. Error messages Causes Countermeasures...
9. Troubleshooting Other messages Indicated when the power is turned on after turning off during printing. MECHA INITIALIZE REQUEST Press the MEMORY button for more than one second while pressing the MONITOR button. *Note : 3 Indicated during initializing. MECHA INITIALIZE In the case of pressing the STOP button on the remote control during PRINT STOP printing, this unit is initialized.
9. Troubleshooting 1 Before calling for service Symptom Check and Remedy 1 No power Is the power cord plug disconnected from the outlet? Connect the power cord plug to the outlet firmly. After turning the power off, wait for approx. 2 minutes. Then turn the power ON.
Page 88
9. Troubleshooting Symptom Check and Remedy 1 The stored image in the memory cannot be Is the SMALL size ink-sheet installed when selecting “S” in “MODE : S/L”? enlarged to fill the maximum print area. Or is the LARGE size ink-sheet installed when selecting “L” in “MODE : S/L”? Check the current setting.
10. Options The following types of ink sheets and print papers are sold separately. Ink sheet Product name Ink sheet size No. of prints Usage PK700S S size For 3 color use PK700L L size For 3 color use Print paper Product name Print size No.
11. Specifications Class Colour Video Copy Processor Model CP700E Printing method Sublimation Dye Thermal 3 colour faces progressive printing ( yellow, magenta and cyan) Print quality Dot resolution max.1216 x 600 pixels Number of grades 256 for each color Printing time Approx.38 sec./ sheet (L size high speed mode) Approx.51 sec./ sheet...
Page 91
Polígono Industrial “Can Magí”, Calle Joan Bucallà 2-4, Apartado de Correos 420, 08190 Sant Cugat del Vallês, Barcelona, Spaín Phone (3) 589-3900 FAX (3) 589-4448 Manufactured by Mitsubishi Electric Corporation 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan Made from recycled paper PRINTED IN JAPAN 871C952H4...