Executing Paste; Single Undo/Redo Paste - Fostex D2424LV Reference Manual

Model D2424LV Reference Manual (Editing Tracks)
• Checking the clipboard data
• Hold down the [STOP] button and press the [PLAY]
button.
The recorder indicates whether the sound data on the
clipboard is a copied data or moved data ("Copy Clip" or
"Move Clip") and plays the data (this is called "clipboard
playback"). Monitor the playback sound through the
mixer channels that correspond to the copied (or moved)
tracks. During clipboard playback, the indicates of the
[RECORD TRACK] select key for the copied (or moved)
track will flash.
• Press the [EDIT] key again to get ready for the paste
operation.
"Copy Paste?" or "Move Paste?" flashes on the display.

• Executing Paste

4. Press the [EXECUTE/YES] key again.
The display indication enables you set the number of
the paste operations. The number and "SURE?" flash.
At this time, the flashing [RECORD TRACK] indicator
becomes continuously lit.
Flashing
SURE?
OL
0
3
6
9
12
18
24
30
42
4
1 2 3 5 6 7 8 9 10 11 12
Track display ( ) of the item to be copied (or moved) will change to lit.
5. Select a destination track to paste data.
• If paste is to be done on the same track, it is not
necessary to select the track.
• Changing the destination track for paste is
permissible to a mono track or adjacent two tracks
in odd and even numbers (1-2, 3-4, 5-6, etc.) only
when the copy (or move) data is on the clip board.
For this procedure, if the [RECORD TRACK] select
key of the track to be changed is pressed, and an
objective track for pasting can be selected.
• If a multiple number of tracks (1-3, 5-8, etc.) other
than those above had been copied (or moved),
paste can be done only to the same track as that
of the copy (or move) originating track.
The track cannot be selected even though the
[RECORD TRACK] select key is pressed.
6. Turn the Jog dial to enter the number of repeats (Repeat
= **).
You can enter up to 99. However, this is automatically
limited by the available recording source on the disk.
That is, if the disk has enough free space, you can set up
to 99 repeats. If the disk has only a small amount of
free space, the Jog dial allows you to set a lower number
of repeats.
7. Press the [EXECUTE/YES] key.
"Copy Paste" (or "Move Paste") flashes and the duration
of the pasted data appears as a negative number on the
display.
Flashing
OL
BIT
0
3
6
9
12
18
24
30
42
13 14 15 16 17 18 19 20 21 22 23 24
This number will count down as the paste operation
proceeds. When the paste operation is complete, the
flashing "Copy Paste" (or "Move Paste") lights up
continuously, and "COMPLETED !" is displayed.
<Note>
If you try to execute the paste operation by pressing
the [EXECUTE/YES] key when the disk has insufficient
free space, " Over !" appears on the display and edit
mode is cancelled.
In this case, you need to delete unnecessary data or
programs.
• Refer to the following section, "Erase," "Deleting a
Program," or "Duplicating a Program."
• Refer to page " 73 " for more information on erasing.
• Refer to page " 37 " for more information on deleting
a program.
• Refer to page " 36 " for more information on
duplicating a program.
8. Press the [EXIT/NO] key or the [STOP] button.
The recorder exits edit mode and displays the previous
Time Base indication.
9. Turn off the [RECORD TRACK] select key of the copy
(or move) source track.

• Single Undo/Redo Paste

24
FS
kHz
CLOCK
INT
You can single undo or redo a Copy & Paste
and Move & Paste operation.
• To restore the data that existed prior to the paste
operation, press the [UNDO/REDO] key.
• To restore the pasted data after you undo the paste
operation, press the [UNDO/REDO] key again.
When you press the [UNDO/REDO] key, the recorder
will undo or redo the operation immediately, and
display "Undo !" or "Redo !" and "COMPLETED !".
<Note>
This function only works when this recorder is in
the stop mode.
<Note>
If you perform one of the following operations
after you use the Copy & Paste or Move and Paste
operation, the Undo/Redo function will no longer
be effective.
1. If a new recording has been made.
2. When a new editing job is executed (such as
Copy & Paste, Move & Paste, Erase).
3. While in the AUTO PUNCH ON mode, when
the AUTO PUNCH IN point is passed in the
PLAY (or RECORD) mode.
4. If the power was switched off.
5. If program select was executed.
6. When multiple undo is executed.
70