Meter Display - Fostex D2424LV Reference Manual

<Note>
If a correct value is not stored, pressing the [AUTO
PUNCH] key will not enable the function, and the
message " Void Out Point!" will appear.
If a correct value is not stored, pressing the [AUTO
PUNCH] key will not turn on the function, and the
message " Void Out Point! " will alert you. In this case, set
a correct value for the Auto Punch In/Out point.
Also, the function is not turned on when you press the
[AUTO PUNCH] key if the disk does not have enough
recording space. The display will indicate " -**H **M **S
**F Over. "
* Refer to page " 40 " for details about Punch In/Out
operation.
31. Shift key
[SHIFT]
Press a key, or button while holding down the [SHIFT]
key to activate the following "shift-invoked" functions.
Key with SHIFT function
[RECORD TRACK] select keys
[TRACK SHIFT] key
[RECORD] button
[CLIPBOARD IN/OUT] key
[AUTO PUNCH IN/OUT] key
[AUTO RTN START/END] key
[EXIT/NO] key
[EXECUTE/YES] key
[DISP SEL] key
[EDIT] key
[SETUP] key
[UNDO/REDO] key
[VARI PITCH] key
[NEXT] key
[PREV] key
[STORE] key
* Refer to page " 107 " for details on the SETUP mode.
* Refer to the "APPENDIX" at end of this manual in
regards to the TC generator mode.
* Refer to page " 66 " for details on multiple undo
function.
* Refer to the "Quick Operation Guide" in regards to
editing of Vari Pitch data.
* Refer to page " 64 " for details on preview.
* Refer to page " 62 " for details on the envelope function.
Model D2424LV Reference Manual (Names and Functions)
Function
Executes the envelope function of
the selected track.
Switches ON/OFF of the input
monitor for all tracks.
Switches SAFE-READY for all tracks.
Executes preview of the stored point
of each memory key.
Ejects disk in the external SCSI drive.
Please see <Note> below.
Switches the slave mode ON/OFF.
Selects the time base.
Switches TC READY ON/OFF.
Enters the TC GEN setup mode.
Enters the multiple undo executing
mode.
Enters the vari pitch data editing
mode.
The recorder will locate to the head
of the next time code event,
subsequent to the recorded time
code. This functions only when an
optional Model 8346 is installed.
The recorder will locate to the head
of the time code event previous to
the recorded time code.
This functions only when an
optional Model 8346 is installed.
Holds the current time data, which
you can edit.
<Note>
Ejecting or removing the backup SCSI disk is only
possible when the drive is set to "SCSI*" via the SETUP
mode "Setup of the drive." If the drive is set to "IDE",
eject it using the SCSI drive EJECT switch.
32. All Input LED
This is lit when all track input monitors are set to
ON by pressing the [TRACK SHIFT] key while pressing
the [SHIFT] key, and extinguished when set to OFF.
While in the SETUP mode, it is also possible to
automatically set it to all input monitors while the
recorder is in the stop mode.
* For details, refer to page 28 at end of this manual.
33. Track shift LED [9-16, 17-24] (green)
This is lit when the selectable recording track is
shifted to 9-16 or 17-24.
34. Hard disk access LED (green)
This LED lights up or blinks when the hard disk is
writing or reading data.
<CAUTION>
Do not turn the power off while this LED is lit or blinking.
Otherwise, data on the hard disk may be damaged.
35. Foot switch jack
(Connector: PHONE jack)
Punch in/out (also for rehearsal) or PLAY/STOP of
the recorder can be done by foot by connecting the
optional foot switch.
The foot switch function can be changed in the SETUP
mode. It will not function for punch in/out function
in the initial setting.).
* Refer to page " 43 " for information about Punch In/
Out recording using the foot switch.
<Note>
Be sure to use an " unlatch type " foot switch if you use a
foot switch other than the Model 8051. Otherwise, a
malfunction could occur.

36. Meter display

This meter display shows the signal level and
settings.
* Refer to the "Display section" on page " 19 ."
17
[ALL INPUT]
[FOOT SW]