Storing And Editing Locate Key; Storing In Real-Time - Fostex D2424LV Reference Manual

Model D2424LV Reference Manual (Storing a Locate Point (Edit Point)
1.While the recorder is stopped, press the memory
key that stores the data you wish to edit.
The stored data appears on the display and the recorder
enters data edit mode.
2.Turn the Shuttle dial to move the flashing cursor
to the time value digit, and use the Jog dial to
increase or decrease the value.
3.Press the [STORE] key.
The "Press LOCATE: ##" menu will appear as indicated
before. Ignore this go to the next step.
4.Press the memory key that you pressed in Step 1
again.
The STORE LED will turn off. The edited data is stored,
and the recorder displays the previous Time Base
indication.
You can store up to 99 individual time data in the [LOCATE] key for Locate only operations.
The time data stored can also be assigned with a specific locate number from 01-99.
This means the desired locate number can be specified to locate that specific time data.
The memory data of the [LOCATE] key can also be edited in the same manner as the data in the
Memory key. After editing the data the [LOCATE] key can locate that point, or even be re-stored as
data for other Memory keys.
<Notes>
• The last data located with the Memory key or [LOCATE] key is constantly stored as LOCATE number 00.
However, this data is constantly replaced after every LOCATE command. Therefore, do not use Locate Number 00
for independent Locate data.
• You cannot preview the data stored in the [LOCATE] key, though it is possible to preview data stored in other
Memory keys.
* If you use a time base that is not an ABS time, there is a need to priory switch to the desired time base using the
[SHIFT] key and [DISP SEL] key.
* Any editing or storing of data for the LOCATE point is valid only for the program that is currently started up.

Storing in real-time

You can store the locate point (in the ABS, MTC, or BAR/BEAT/CLK Time Base) in real-time while the
recorder is playing.
POWER
1.Press the [PLAY] button to start playback.
2.Press the [STORE] key (the STORE LED lights up).
The memory number selection menu will appear, as
follows.
Storing and editing [LOCATE] key
24TRACK DIGITAL RECORDER
RECORD TRACK
1/9/17 2/10/18 4/12/20 5/13/21 6/14/22 7/15/23
3/11/19
FOOT SW
ENVELOPE
ACCESS 9-16 17-24
• You can store the edited data in a memory key other
than the one you pressed when you recalled the data.
For example, you can recall the AUTO PUNCH IN point
data, edit it, and store it to the [AUTO PUNCH OUT]
key.
• You can also use the Preview function to edit the
stored locate points (edit points). Refer to " Preview
Function " on page " 64 " for more information.
• Refer to page " 40 " for more information on Auto
Punch In/Out.
• Refer to page " 68 " for more information on Copy &
Paste, Move & Paste, and Erase.
• Refer to page " 55 " for more information on Auto
Return and Auto Repeat.
1 4
5
AUTO RTN
AUTO RTN
CLIPBOARD AUTO PUNCH
AUTO PLAY START
IN OUT IN OUT
PREVIEW
CHARACTER
EDIT SETUP UNDO/REDO PREV
SHIFT PREV TC
TC READY TC GEN M.UNDO
AUTO
REHEARSAL
24bit LOCATE VARI PITCH
PUNCH
96kHz
TAKE
OPTICAL
RECORD STOP PLAY REW
TRACK SHIFT
8/16/24
ALL INPUT ALL READY
TRACK SHIFT CLIPBOARD PLAY
LOCATE ABS 0
LOCATE REC END
OL
0
3
6
9
12
18
24
30
42
1 2 3 4 5 6 7
53
2
PGM SEL EXIT/NO EXECUTE/YES
END
EJECT CHASE
LOCATE MEMORY
NEXT DISP SEL STORE RECALL
NEXT TC TIME BASE SEL HOLD
P.EDIT
F FWD
Flashing
H M
8 9 18 20 21 22 23 24
10 11 12 13 14 15 16 17 19
3
LOCATE
S F SF
OL
24
BIT
0
3
FS
6
9
kHz
12
18 CLOCK
24 INT
30
42