Executing The Preview Function; Trimming The Sound While Previewing - Fostex D2424LV Reference Manual

1. Press the desired memory key while holding down the
[SHIFT] key when the recorder is stopped.
Pressing the desired memory key will enable you to
preview the sound at the locate point (edit point) stored
in the corresponding memory key.
Memory key
[AUTO PUNCH IN] key
[AUTO RTN END] key
[CLIPBOARD OUT] key
[AUTO PUNCH OUT] key
[AUTO RTN START] key
[CLIPBOARD IN] key
You can trim the position of the locate point (edit point) using the Jog dial while you preview the
sound. At this time, you can also adjust the size of the trimming steps (the amount of offset
controlled by the Jog dial).
Trimming allows you to fine-tune the position of the locate point stored in the memory keys
while previewing the sound. Use this function to change the Auto Punch In/Out points, the start
point of Copy & Paste and Move & Paste, and the start and end points of the Erase function.
<Notes>
• You can audition the result of trimming during the next preview. That is, if you trim the position while previewing
the sound for the first time, you can check the result when you preview the sound next time.
• If the locate point is shifted outside the range of the preview playback as a result of trimming, " Void Data! " and the
locate point indication appear alternately. In this case, you cannot use the Preview function. Trim the position
again so that it will be within the playback range.
• When Auto Punch mode is turned on and you trim the Auto Punch In or Auto Punch Out point while previewing the
sound with " Void Data! " indicated on the display, Auto Punch mode will be cancelled.
1. Start previewing the sound by following the steps
described on the previous page.
2. Use the Jog dial to trim the position.
When previewing starts, the unit of Jog trimming
flashes on the screen.
For example, value of SF (sub-frame) flashes if ABS Time
Base or MTC Time Base is selected. CLK (clock) flashes
if BAR/BEAT/CLK is selected. The flashing value also
indicates the position you can trim.
OL
0
3
6
9
12
18
24
30
42
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
OL
0
3
6
9
12
18
24
30
42
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Model D2424LV Reference Manual (Preview Function)

Executing the Preview function

Operation
The recorder plays the fall
(fade out) of the sound at the
locate point stored in the keys.
The recorder plays the fall
(fade in) of the sound at the
locate point stored in the keys.

Trimming the sound while previewing

Flashing
LOCATE
H M S F
OL
BIT 24
0
3
6
9
12
CLOCK
18
24
30
42
Flashing
LOCATE
BAR CLK
OL
24
BIT
0
3
6
9
12
18 CLOCK
24 INT
30
42
2. Adjust the monitor sound of the selected track so that
it can be monitored on the mixer.
<Note>
If data stored in each memory key is in the initial state,
all memory keys will be in ABS time 00H 00M 00S.
In other words, the program head value is in the
memory. Should fade out preview be executed in this
condition, the " Void Data! " message and memory data
" 00H 00M 00S " will alternately flash in the display as a
warning. However, for fade in preview, this will
function as the memory data " 00H 00M 00S " point.
3. Press the [STOP] button or the [EXIT/NO] key.
3. To change the unit of trimming, turn the Shuttle dial.
Shuttle dial
(clockwise)
Shuttle dial
(counter clockwise)
SF
FS
4. Trim the position at the selected unit (digit).
kHz
INT
5. Press the [STOP] button or the [EXIT/NO] key.
The trimmed locate point (edit point) data will be stored
in the corresponding memory key.
FS
kHz
65
Time base
ABS or MTC BAR/BEAT/CLK
M S
SF H F
H M S F
SF
CLK BAR
BAR
CLK