Sound Setting; Adjusting Subwoofer Level/Bass Level/Treble Level/Balance (Between Left And Right)/Fader (Between Front And Rear)/Auto Volume/Defeat; Setting The Subwoofer Level; Setting The Bass Control - Alpine CDA-9886R Owner’s Manual

Sound Setting

Rotary encoder (AUDIO·LOUD)
SOURCE/
BAND/TA
/ESC
Adjusting Subwoofer Level/Bass Level/
Treble Level/Balance (Between Left and
Right)/Fader (Between Front and Rear)/
Auto Volume/Defeat
1
Press Rotary encoder (AUDIO) repeatedly to
choose the desired mode.
Each press changes the mode as follows:
1
SUBWOOFER* BASS
FADER AUTO VOLUME*
SUBWOOFER
Subwoofer level: 0 ~ +15
Bass level: –7 ~ +7
Treble level: –7 ~ +7
Balance: L15 ~ R15
Fader: R15 ~ F15
Auto Volume: OFF/LOW/MIDDLE/HIGH
Defeat: ON/OFF
Volume: 0 ~ 35
• If no operation is performed for 5 seconds after selecting the
SUBWOOFER, BASS, TREBLE, BALANCE, FADER, AUTO
VOLUME or DEFEAT mode, the unit automatically returns to
normal mode.
1
* When the subwoofer mode is set to OFF, its level cannot be adjusted,
refer to "Turning Subwoofer ON/OFF" (page 18).
2
* By setting AUTO VOLUME, the unit can automatically adjust
volume to a proper level according to engine/road noise, etc. There
are three volume correction degrees: LOW, MIDDLE and HIGH.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
By setting Defeat ON, previously adjusted settings of BASS
and TREBLE will return to the factory defaults.
• Depending on the connected devices, some functions and display
indications do not work.
16
-EN
/ENT
SOUND SETUP
TREBLE BALANCE
2
DEFEAT VOLUME

Setting the Subwoofer Level

You can change the Subwoofer Level to create your own tonal
preference.
1
Press SOUND SETUP to activate the Sound Setting
mode.
2
Turn the Rotary encoder to select the SUBW. Level
Adjustment mode, and then press
3
SUBW. Level* Bass*
Black Out SUBW. Level
3
Turn the Rotary encoder to select the desired
subwoofer level (0~+15).
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
3
* When the subwoofer mode is set to OFF, its level cannot be adjusted,
refer to "Turning Subwoofer ON/OFF" (page 18).
The adjustment can also be made by pressing Rotary encoder
(AUDIO). Refer to "Adjusting Subwoofer Level/Bass Level/Treble
Level/Balance (Between Left and Right)/Fader (Between Front and
Rear)/Auto Volume/Defeat" (page 16).
4
* The function is inoperable when DEFEAT is set to ON.

Setting the Bass Control

You can change the Bass Frequency emphasis to create your own tonal
preference.
1
Press SOUND SETUP to activate the Sound Setting
mode.
2
Turn the Rotary encoder to select the Bass
Adjustment mode, and then press
5
SUBW. Level* Bass*
Black Out SUBW. Level

Setting the Bass Centre Frequency

3
-1 Press BAND/TA to select the desired bass centre
frequency.
80 Hz 100 Hz 200 Hz
Emphasises the displayed bass frequency ranges.

Setting the Bass Bandwidth

3
-2 Press SOURCE/ to select the desired bass
bandwidth.
Q1 Q2
Changes the boosted bass bandwidth to wide or narrow. A
wider setting will boost a wide range of frequencies above
and below the centre frequency. A narrower setting will
boost only frequencies near the centre frequency.
/ENT.
4 4 4
Treble* HPF*
/ENT.
6 6 6
Treble* HPF*
60 Hz 80 Hz
Q3 Q4