Recalling Preset Rds Stations; Receiving Rds Regional (Local) Stations; Pi Seek Setting; Setting Pty31 (Emergency Broadcast) Reception - Alpine CDA-9886R Owner’s Manual

Recalling Preset RDS Stations

1
Press F/SETUP to activate the function mode.
2
Press 1 AF to activate the RDS mode.
3
Press F/SETUP to activate the preset mode.
4
Make sure that the function mode returns to preset
mode, and then press the preset button in which
your desired RDS station is preset.
If the preset station's signal is weak, the unit automatically
searches and tunes to a stronger station in the AF
(Alternative Frequencies) list.
5
If the preset station and the stations in the AF list
cannot be received:
When the PI SEEK setting is on (refer to "PI SEEK Setting"
on page 9), the unit searches again for a station in the PI
(Programme Identification) list.
If there are still no stations receivable in the area, the unit
displays the frequency of the preset station and the preset
No. disappears.
If the signal level of the Regional (Local) station being tuned
becomes too weak to receive, press the same preset button
to tune in a Regional station in other district.
• For presetting the RDS stations, refer to the Radio Operation section.
The RDS stations can be preset in the FM1, FM2 and FM3 bands
only.
• Operate the unit while the function mode is activated. If no operation
is performed for 5 seconds, the function mode is cancelled.
Receiving RDS Regional (Local)
Stations
1
Press and hold F/SETUP for at least 2 seconds to
activate the SETUP mode.
2
Turn the Rotary encoder to select the Tuner mode,
and then press /ENT.
Bluetooth General
3
Turn the Rotary encoder to select RDS Regional,
and then press /ENT.
4
Turn the Rotary encoder to select ON or OFF.
In the OFF mode, the unit automatically keeps receiving the
related local RDS station.
5
Press and hold F/SETUP for at least 2 seconds to
return to normal mode.
• Pressing /ESC during the procedure will return to the previous
mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
Display Tuner Bluetooth

PI SEEK Setting

1
Press and hold F/SETUP for at least 2 seconds to
activate the SETUP mode.
2
Turn the Rotary encoder to select the Tuner mode,
and then press /ENT.
Bluetooth General
3
Turn the Rotary encoder to select PI Seek, and
then press /ENT.
4
Turn the Rotary encoder to select ON or OFF.
5
Press and hold F/SETUP for at least 2 seconds to
return to normal mode.
• Pressing /ESC during the procedure will return to the previous
mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
Setting PTY31 (Emergency Broadcast)
reception
Turn PTY31 (Emergency Broadcast) reception ON/OFF.
1
Press and hold F/SETUP for at least 2 seconds to
activate the SETUP mode.
2
Turn the Rotary encoder to select the Tuner mode,
and then press /ENT.
Bluetooth General
3
Turn the Rotary encoder to select Alert PTY31, and
then press /ENT.
4
Turn the Rotary encoder to select ON or OFF.
If you set to ON, emergency broadcasts are received
regardless of source. "ALARM" is displayed during
reception.
5
Press and hold F/SETUP for at least 2 seconds to
return to normal mode.
When an emergency broadcast is received, the volume
level will be automatically changed to the memorized level
in the traffic information mode. For details, refer to
"Receiving Traffic Information" on page 10.
• Pressing /ESC during the procedure will return to the previous
mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
Display Tuner Bluetooth
Display Tuner Bluetooth
9
-EN