Sound Setting; (Between Left And Right)/Fader (Between; Front And Rear)/Loudness/ Defeat; Setting The Bass Control - Alpine iDA-X100M Quick Reference Manual

Sound Setting
Double Action encoder
IMPRINT
If either an external or IMPRINT audio processor is connected. the
Sound Setup screen is not displayed. For an external audio processor,
refer to "Audio Selling" (page 23) of "SETUP" (page 20) to adjust the
sound. For an IMPRINT audio processor, refer to "IMPRINT Operation
(Optional)" (page 29) to adjust the sound.
Adjusting SubwDoferlBasslTreble/ Balance
(Between Left and Right)/Fader (Between
Front and Rear)/loudness/ Defeat
1
Press IMPRINT repeatedly to choose the desired
mode,
Each press changes the mode as follows:
Subwoofer*'
~
Bass Level
~
Treble Level
~
Balance
~
Fader ~ Loudness ~ Defeat ~ Volume ~ Subwoofer
Subwoofer: 00 - 15
Bass level: -7 - +7
Treble level: -7 - +7
Balance: Left15 - Right15
Fader: Rear15 - Front15
Loudness: ON/OFF
Defeat: ON/OFF
Volume: -00 -0 dB
• Loudness introduces a special low and high frequency
emphasis at low listening levels. This compensates for the
ear's decreased sensitivity to bass and treble sound. The
function is inoperable when Defeat is set to ON,
• By setting Defeat ON, previously adjusted setting of Bass,
Treble and High Pass Filter will return to the factory defaults.
• I!'IMPRINT is not pressed for 15 seconds ajier selecting the
SlIbwoo./er. Bass, Treble. Balance or Fader /llOde. the linit
alltomlltically returns to /lormal mode.
*1
When the sub woofer mode is set to OFF, its level connot be adjusted.
2
Rotate the Double Action encoder until the
desired sound is obtained in each mode.
• Depending on the connected devices. somejil1lctions do not work.
• You can store the cOlltellts o./'BalallcdFader/Lolldness settillgs ajier
completing. For how to store. refer to "Storing the Alldio Adjustmelll
LeI'el" (page 23).
i8-EN
Setting the Bass Control
You can change the Bass Frequency emphasis to create your own tonal
preference.
1
Press and hold IMPRINT for at least 2 seconds.
The Sound Setup screen is displayed.
2
Press
~/ENTER.
The Bass Adjustment setting mode is activated.
$e!:tlngthe'Ba8~,genter
,Freq,uency
3
Press
~/ENTER.
The Fa setting screen is displayed.
4
Press
~/ENTER.
5
Rotate the Double Action encoder to select the
desired bass center frequency, and then press
~/ENTER.
60 Hz +-+ 80 Hz +-+ 100 Hz +-+ 200 Hz
Emphasizes the displayed bass frequency ranges.
6
Press
~
to return to Bass Adjustment mode.
$@nlngth.~1I8.,~ndwidtbt;:,.., :V",' ' . '
"'/'-'-:j-;,;-'''';' .,;_. _, ' , ' ,
,;,'·;,:>:<;:;:.".'i:;;.::-,';','i'''::; ;":_~';'~ ..
:',::""···Y;·'·',';',<'i'"·;.,,,:,,,;,{.·,
'·;;'i,,··;,,~-,,(;;,·:·,,:·;·:·::b._ .::.;~,~" .
3
Rotate the Double Action encoder to select "0",
and then press ~/ENTER.
The Q setting screen is displayed,
4
Press
~/ENTER.
5
Rotate the Double Action encoder to select the
desired bass bandwidth.
1+-+1.25+-+1.5+-+2
Changes the boosted bass bandwidth to wide or narrow. A
wider setting will boost a wide range of frequencies above
and below the center frequency. A narrower setting will
boost only frequencies near the center frequency.
6
Press
~
to return to Bass Adjustment mode.
• (I' ~
is pressed during settillg. the unit retums to the previous item.
• The jilllction is inoperable when Dejeat is set to ON.
• YOli can adjust the bass level in normal mode. For dewils. re.fer
to
"Adjllsting SubwoojerlBasslTreble/ Balance (Between Left and
Right)/Fader (Between From and Rear)ILoudllenf Dejeat" (page 18).
• Ajier the setting. storing the setting contents
011
the unit is
recommended. For details. rejer to "Storing the Audio Adjllstmem
Level" (page 23).
• The bass level settings will be individually memori:edfor each
SOllrce (FM. AM, CD. etc.) lin til the setting is chllnged. The bass
frequency and bliSS bandwidth settings adjusted!l,r one source are
ejfective for al/ other sources (FM. AM. CD. etc.)