Connections - Aiphone IS SERIES Installation Manual

■ Connections

PA output
(50mVrms, 600Ω)
PA amplifi er
*1
NP NP
2C 2C
φ0.65-1.2mm φ0.65-1.2mm
(22-16 AWG) (22-16 AWG)
15m (50')
AC
transformer
NP: Non-polarized
P: Polarized
P1 P2 P3
PA OUTPUT (600Ω)
IS-RCU
1CX1 2CX1 3CX1
1CX2 2CX2 3CX2
CAT5e/6 CAT5e/6
(non-shielded) (non-shielded)
200m 200m
(650') (650')
CX1/IP1 CX2/IP2
Room sub control unit
(IS-RCU)
*1: This connection is needed when a PA amplifi er that needs a trigger input is connected. (Up to AC/DC 24V 0.5A)
*2: This connection is needed when a sound source etc. that needs a trigger input is connected. (Up to AC/DC 24V 0.5A) Connect a timer to the
CONTACT INPUT terminals when an external sound source device (CD player etc.) that does not have a timer function is connected.
*3: This connection is needed when a sound source that has a trigger output is connected.
*4: Refer to the SETTING MANUAL for connection and settings.
*5: Do not install two power supplies in parallel to a single input. Be sure to connect a single power supply unit to a control unit.
*6: Do not use an external sound source as background music. If the background music is interrupted by another performance during chime paging,
the chime paging will not be restored after the performance ends.
*7: Outputs images only from a video door station connected to this unit.
*8: Output specifi cations
Output method N/O or N/C dry closure contact
Voltage between 24V AC, 0.5A (resistive load)
24V DC, 0.5A (resistive load)
terminals
Minimum overload (AC/DC): 100mV, 0.1mA
NOTES:
Do not use the unoccupied terminals and ports for other purposes.
•
In order to prevent miswiring, label both ends of each cable with
•
the unit and terminal names to which they are to be connected.
For connecting other manufacturer's products, refer to the
•
instruction manuals for those products.
The illustration of the unit's front panel differs from the actual
•
one. This is for simplifying the connection diagram.
*8
Contact output
(Electric door strike, strobe light, etc.)
NP
2C
φ0.65-1.2mm
(22-16 AWG)
PT
P4 L1 L2 L3 L4 L5 L6
CONTACT OUTPUT (AC/DC24V 0.5A)
MASTER STATION
4CX1 M1 M3
4CX2 M2 M4
CAT5e/6
CAT5e/6
(non-shielded)
(non-shielded)
300m 150m
(980') (490')
M C
Master station
Room sub station
(IS-MV)
(IS-RS)
Chime input (50mVrms, 600Ω)
External sound
Contact input *9
source such as
Sensor, etc.
CD player, etc.
*2 *3
NP
P
2C
2C
φ0.65-1.2mm
φ0.65-1.2mm
(22-16 AWG)
(22-16 AWG)
15m (50')
P
2C
φ0.65-1.2mm
(22-16 AWG)
15m (50')
L7 L8 S1 E S2 E S3 E S4 E
CONTACT INPUT
VIDEO/AUDIO
DOOR/SUB STATION
IS-SCU
D1 D3 1MX1 1MX3
D2 D4 1MX2 2MX1
CAT5e/6
(non-shielded)
300m
(980')
or
D
MX1 MX2 MX3
Add-on control unit
Door station
(IS-SCU)
(IS-DV/IS-DVF/
IS-SS)
*9: Input specifi cations
Input method
Detection confi rmation
time
Contact resistance
Terminal short current
Voltage between
terminals
*7 *7
Monitor 1, Monitor 2,
*6
Recorder 1 Recorder 2
BNC
BNC
NP
connector
connector
2C
φ0.65-1.2mm
(22-16 AWG)
15m (50')
Coax Coax
15m (50') 15m (50')
NTSC NTSC
BNC BNC
connector
connector
B1 B2
V1 V2
CHIME INPUT (600Ω) VIDEO OUTPUT
IS-IPC
2MX2 IP1
2MX3 IP2 IP3
CAT5e/6 (x3)
CAT5e/6 (x3)
(non-shielded)
(non-shielded)
200m
10m (33')
(650')
IP1 IP2 IP3
IP control unit
(IS-IPC)
N/O or N/C dry closure contact (start
signal only detection method)
100 ms or more
During N/O dry closure: Less than 700 Ω
During N/C dry closure: At least 4 k Ω
Less than 10 mA
Less than 5 V DC (when open between
terminals)
PC for setting
the system
*4
LAN
ETHERNET
DC48V
2C
φ0.8-1.2mm
(20-16 AWG)
P
15m
(50')
*5
Power supply unit
(IS-PU-UL/IS-PU-S)
11