Summary of Contents for Intel S5000XVN - Workstation Board Motherboard
Page 1
® Intel Workstation Board S5000XVN User Guide A Guide for Technically Qualified Assemblers of Intel® Identified Subassemblies/ Products Intel Order Number D36222-004...
Page 2
Intel products are not designed, intended or authorized for use in any medical, life saving, or life sustaining applications or for any other application in which the failure of the Intel product could create a situation where personal injury or death may occur.
Safety Information Important Safety Instructions Read all caution and safety statements in this document before performing any of the instructions. See also Intel Server Boards and Server Chassis Safety Information on the ® Intel Server Deployment Toolkit 2.0 CD and/or at http://support.intel.com/support/...
Page 4
重要安全指导 在执行任何指令之前,请阅读本文档中的所有注意事项及安全声明。 和/或 http://support.intel.com/support/motherboards/server/sb/CS-010770.htm 上的 Intel Server Boards and Server Chassis Safety Information(《Intel 服务器主板与服务器机箱安全信息》)。 ® Intel Workstation Board S5000XVN...
Take care to grip with, but not squeeze, the pliers or other tool you use to remove a jumper, or you may bend or break the pins on the board. ® Intel Workstation Board S5000XVN...
Preface About this Manual ® Thank you for purchasing and using the Intel Workstation Board S5000XVN. ® Multiple versions of the Intel Workstation Board S5000XVN are available. This manual applies to workstation boards with the following product codes: • S5000XVNSATA •...
Processor, memory FBDIMMs, hard drive, USB floppy drive, CD-ROM or DVD-ROM drive, RAID controller, operating system. For information about which accessories, memory, processors, and third-party hardware have been tested and can be used with your board, and for ordering information for Intel products, see http://support.intel.com/support/motherboards/server/S5000XVN/ compat.htm.
Page 9
Table 1. Additional Information and Software For this Information or Use this Document or Software Software Accessories or other Intel Spares and Configuration Guide. server products See the section on the web page titled Installation and Use. Hardware and operating Tested Hardware Operating Systems List.
Additional Information and Software ..................viii Chapter 1: Workstation Board Features ..............1 Connector and Header Locations ..................4 Configuration Jumpers ......................6 ® Intel Light-Guided Diagnostics ..................... 8 Back Panel Features ......................11 RAID Support ........................12 SATA Workstation Board .....................12 SAS Workstation Board ....................13 Audio Support ........................14...
Page 12
Clearing the Password ......................24 Clearing the CMOS ......................25 Chapter 3: Hardware Installations and Upgrades ..........27 Before You Begin ........................ 27 Tools and Supplies Needed ..................27 Installing and Removing Memory ..................27 Installing FBDIMMs ..................... 27 Removing FBDIMMs ....................30 Installing or Replacing the Processor ..................
Workstation Board Features ® This chapter briefly describes the main features of the Intel Workstation Board S5000XVN. This chapter provides a photograph of the product, a list of the workstation board features, and diagrams showing the location of important components and connections on the workstation board.
Up to two 45nm 2P Dual-Core Intel Xeon processors. Product code S5000XVNSATAR and S5000XVNSASR only • ® ® Up to two 45nm next generation Quad-Core Intel Xeon processors. Product code S5000XVNSATAR and S5000XVNSASR only • System memory support Eight FBDIMM sockets (DDR2-533 and DDR2-667) supporting 32 GB maximum memory •...
Page 21
® Product code S5000XVNSATA or S5000XVNSATAR: Intel Embedded Server RAID Technology II provides SATA RAID 0, ® 1, and 10 with optional RAID 5 support provided by the Intel RAID Activation Key AXXRAKSW5 • ® Product code S5000XVNSAS or S5000XVNSASR: Intel...
Table 2. Workstation Board Features Feature Description • ® Management support Support for the Intel Local Control Panel (optional component sold separately) • ® Support for Intel System Management software • ® Intel Light-Guided Diagnostics on field replaceable units •...
Page 23
QQ. Serial B / emergency SATA GPIO header (only management port header with product code S5000XVNSATA or S5000XVNSATAR) ® Auxiliary power signal CC. Intel Local Control Panel RR. Chassis intrusion header connector header DIMM sockets (see Figure 5 DD. Hot-swap backplane B...
CMOS: Power down the workstation, leaving AC power connected. Place the jumper on pins 2 - 3 for 5 to 10 seconds. Move the jumper back to pins 1 - 2. Power on the workstation ® Intel Workstation Board S5000XVN...
BMC Force Update 1 - 2 Disable force update: These pins should be jumpered for normal operation. (J1E3) 2 - 3 Enable force update: Jumpering these pins forces a BMC update. Figure 3. Configuration Jumpers ® Intel Workstation Board S5000XVN...
® Intel Light-Guided Diagnostics The workstation board contains diagnostic LEDs to help you identify failed and failing components and to help you identify the workstation from among several workstations. Except for the ID LED, the status LED, and the +5-volt standby LED, the LEDs turn on (amber) only if a failure occurs.
Page 27
This LED indicates a fault has occurred with the FBDIMM installed in socket DIMM_A2. Replace the faulty FBDIMM. DIMM B1 fault LED This LED indicates a fault has occurred with the FBDIMM installed in socket DIMM_B1. Replace the faulty FBDIMM. ® Intel Workstation Board S5000XVN...
Page 28
Processor 1 fan fault LED This LED applies only to workstation systems that use an active heatsink. This LED indicates a fault has occurred with fan that is installed on the heatsink for processor 1. Replace the faulty unit. ® Intel Workstation Board S5000XVN...
Back Panel Features The diagram and table show the back panel connectors and LEDs. For information about ® the LEDs, see “Intel Light-Guided Diagnostics” on page AF000501 Mouse LSB LED (POST LED) Serial A Bit 1 LED (POST LED NIC 1...
I interface. Notes: ® • For help with navigating the BIOS Setup utility, see the Intel Workstation Board S5000XVN Technical Product Specification. • For help with enclosure management cabling, see the Enclosure Management Cabling Guide for Pedestal Systems with Hot-swap Drive Backplanes.
SATA ports are disabled. ® • When the SAS option ROM is enabled in the BIOS Setup utility, Intel Embedded Server RAID Technology II is available. This enables SAS RAID modes 0, 1, or 10 for the four blue ports on the workstation board. This SAS controller can mix SAS and SATA drives and the RAID mode of this SAS controller supports up to eight SAS/SATA physical drives and eight logical drives.
Audio Support ® The Intel Workstation Board S5000XVN includes the Realtec* ALC260 2-channel high- definition audio codec with universal audio architecture. It features a 24-bit, 2-channel DAC and two stereo 20-bit ADCs. The ALC260 provides two output channels with flexible mixing, mute and fine gain controls to provide a complete integrated audio solution.
5000 / 5100 sequence or Quad-Core ® ® Intel Xeon processors 5300 sequence. ® ® • One or two 45 nm next generation Quad-Core Intel Xeon processors (Product codes S5000XVNSATAR and S5000XVNSASR only) ® ® • One or two 45 nm 2P Dual-Core Intel Xeon...
Information and Software” on page viii Power Supply A minimum of 550 watts is required. Your power supply must provide a minimum of 3 amps of 5-volt standby current or the workstation will not boot. ® Intel Workstation Board S5000XVN...
Optional Hardware ® Intel RAID Activation Key ® The Intel RAID Activation Key AXXRAKSW5 can be purchased and installed to enable RAID 5 support on your workstation board. For the SATA workstation board, product codes S5000XSLSATA and S5000XSLSATAR, ® an Intel RAID Activation Key can be installed in the SATA RAID 5 Key connector.
System Utilities Using the BIOS Setup Utility This section describes the BIOS Setup Utility options, which is used to change system configuration defaults. You can run BIOS Setup with or without an operating system being present. See “Additional Information and Software” for a link to the Technical Product Specification where you will find details about specific BIOS setup screens.
When the <Esc> key is pressed in any submenu, the parent menu is re-entered. When the <Esc> key is pressed in any major menu, the exit confirmation window is displayed and the user is asked whether changes can be discarded. ® Intel Workstation Board S5000XVN...
BIOS, the system reverts to the BIOS that was in place before the upgrade was performed. This provides a safeguard against problems that might happen during the upgrade, such as a power outage during the upgrade process. This is called the rolling BIOS feature. ® Intel Workstation Board S5000XVN...
Note: You may encounter a CMOS Checksum error or other problem after reboot. If this happens, shut down the system and boot it again. CMOS checksum errors require that you enter Setup, check your settings, save your settings, and exit Setup. ® Intel Workstation Board S5000XVN...
5. Close the chassis. 6. Reconnect the AC power and power up the workstation. The BIOS will boot to the previous BIOS until you either move the jumper again or until you perform another BIOS update. ® Intel Workstation Board S5000XVN...
5. Power up the workstation and wait 10 seconds. 6. Power down the workstation. 7. Move the Password Clear jumper back to the original position, covering pins 1 and 2. 8. Close the chassis. 9. Power up the workstation. ® Intel Workstation Board S5000XVN...
Figure 8. CMOS Clear Jumper in the Clear CMOS Position 5. Wait 10 seconds. 6. Move the CMOS Clear jumper back to the original position, covering pins 1 and 2. 7. Close the chassis. 8. Power up the workstation. ® Intel Workstation Board S5000XVN...
Hardware Installations and Upgrades Before You Begin Before working with your workstation product, pay close attention to the “Safety Information” on page iii. Tools and Supplies Needed • Phillips* (cross head) screwdriver (#1 bit and #2 bit) • Needle nosed pliers •...
6. Disconnect and remove any components necessary to access the DIMM sockets. See the documentation that came with your chassis for instructions on removing chassis components. AF000503 Callout DIMM Socket Callout DIMM Socket DIMM_A1 DIMM_C1 DIMM_A2 DIMM_C2 DIMM_B1 DIMM_D1 DIMM_B2 DIMM_D2 Figure 9. Locating DIMM Sockets ® Intel Workstation Board S5000XVN...
See the documentation that came with your chassis for instructions on removing chassis components. 14. Replace the chassis cover and reconnect the AC power cord. See the documentation that came with your chassis for instructions on installing the chassis cover. ® Intel Workstation Board S5000XVN...
(1) Touch the metal chassis before touching the processor or workstation board. Keep part of your body in contact with the metal chassis to dissipate the static charge while handling the processor. (2) Avoid moving around unnecessarily. ® Intel Workstation Board S5000XVN...
4. Remove the chassis cover. See the documentation that came with your chassis for instructions on removing the cover. 5. Locate the processor sockets (see Figure 11). AF000506 Callout Processor Socket Callout Processor Socket CPU_2 CPU_1 Figure 11. Locating Processor Sockets ® Intel Workstation Board S5000XVN...
Figure 12. Opening Processor Socket Lever 8. Push down on the rear tab of the load plate to swing the front of the load plate up slightly. Fully open the load plate. See Figure AF000096 Figure 13. Opening Load Plate ® Intel Workstation Board S5000XVN...
13. Close the socket lever. Push downward on the socket lever while pushing it toward the center of the to engage it under the hook on the processor socket. 14. Install the heatsink(s). See “Installing the Heatsink(s)” on page 34 for instructions. ® Intel Workstation Board S5000XVN...
The following table ® shows the Intel server chassis compatible with this workstation board and whether each chassis requires an active or a passive heatsink: ® Table 5. Heatsink Requirements for Compatible Intel Server Chassis Server Chassis Heatsink Requirement ® Intel...
16. Do not fully tighten one screw before loosely attaching the others. 4. In the same order, gradually and equally tighten each captive screw until each is firmly tightened. Do not fully tighten one screw at a time. AF000098 Figure 16. Installing Heatsink (passive heatsink shown) ® Intel Workstation Board S5000XVN...
See the documentation that came with your chassis for instructions on installing chassis components. 7. Replace the chassis cover and reconnect the AC power cord. See the documentation that came with your chassis for instructions on installing the cover. ® Intel Workstation Board S5000XVN...
Doing so will cause your workstation to overheat and may cause permanent damage. — The heatsink has Thermal Interface Material (TIM) located on the bottom of it. Use caution when handling the heatsink so you do not damage the TIM. ® Intel Workstation Board S5000XVN...
Figure 18. Opening Processor Socket Lever 11. Push down on the rear tab of the load plate to swing the front of the load plate up slightly. Fully open the load plate. See Figure AF000415 Figure 19. Opening Load Plate ® Intel Workstation Board S5000XVN...
13. Store the processor in the packaging materials in which it came. 14. Install the protective cover over the load plate if a replacement processor will not be installed. AF000417 Figure 21. Installing Protective Cover onto Load Plate ® Intel Workstation Board S5000XVN...
Varning: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. Varoitus: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. ® Intel Workstation Board S5000XVN...
11. Replace the chassis cover and reconnect the AC power cord. See the documentation that came with your chassis for instructions on installing the cover. 12. Run the BIOS Setup utility to restore the configuration settings to the real-time clock. ® Intel Workstation Board S5000XVN...
In addition to the system firmware and files, also update any drivers used for components you have installed in your system, such as video drivers and network drivers. Intel provides a package called the “Platform Confidence Test” that may help with your diagnostics. See “Additional Information and Software”...
Are all integrated components from the tested components lists? Check the tested memory, and chassis lists, as well as the supported hardware and operating system list. See “Additional Information and Software” on page viii for links to the tested component lists. ® Intel Workstation Board S5000XVN...
DVD-ROM Drive Activity Light Does Not Light” on page ® • If system LEDs are illuminated, see “Intel Light-Guided Diagnostics” on page 8 for a description of the lights. Confirming Loading of the Operating System Once the system boots up, the operating system prompt appears on the screen. The prompt varies according to the operating system.
Make sure the chassis standoffs are installed only below mounting holes. Misplaced standoffs can contact the pins on the bottom of the workstation board and cause a short. • In a DC powered system, make sure all DC cables are connected. ® Intel Workstation Board S5000XVN...
5. If you do not receive a beep code and characters do not appear, the video display monitor or video controller may have failed. Contact your service representative or authorized dealer for help. ® Intel Workstation Board S5000XVN...
CD-ROM Drive or DVD-ROM Drive Activity Light Does Not Light Check the following: • Are the CD-ROM/DVD-ROM drive's power and signal cables properly installed? • Are all relevant switches and jumpers on the drive set correctly? • Is the drive properly configured? ® Intel Workstation Board S5000XVN...
Make sure your BIOS is current. See “Additional Information and Software” for a link to the current version. • Make sure the other adapter supports shared interrupts. Make sure your operating system supports shared interrupts. • Try reseating the add-in adapter. ® Intel Workstation Board S5000XVN...
If you are running the software from a USB floppy disk, CD-ROM or DVD-ROM, try a different disk. • Make sure the correct device drivers installed. If the problems persist, contact the software vendor's customer service representative. ® Intel Workstation Board S5000XVN...
Devices are not Recognized under Device Manager (Windows* Operating System) ® The Windows* operating systems do not include all of the drivers for the Intel chipsets, onboard NICs, and other components. See “Additional Information and Software” on page viii for a link to the current drivers and chipset files.
Make sure the BIOS is configured to allow the CD-ROM to be the first bootable device. LED Information ® The Intel Workstation Board S5000XVN includes LEDs that can aid in troubleshooting ® your system. For the location of the LEDs, see “Intel...
® In addition to the beep codes above, additional beep codes are provided if an Intel ® Remote Management Module is installed. The Intel Remote Management Module provides the following additional beep codes. ® Table 8. Error Beep Codes Generated by Intel...
(EMC) regulations when ® installed a compatible Intel host system. For information on compatible host system(s) see Intel's Server Builder Web site or contact your local Intel representative. • FCC /ICES-003 - Emissions (USA/Canada) Verification •...
EMC Marking (Class A) Canada CANADA ICES-003 CLASS A CANADA NMB-003 CLASSE A BSMI Marking (Class A) Taiwan Ctick Marking Australia / New Zealand RLL MIC Mark Korea See the regulatory information document for additional information. ® Intel Workstation Board S5000XVN...
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions related to the EMC performance of this product, contact: Intel Corporation 5200 N.E. Elam Young Parkway Hillsboro, OR 97124-6497 1-800-628-8686 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Interference (VCCI) from Information Technology Equipment. If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. ® Intel Workstation Board S5000XVN...
RRL (Korea) English translation of the notice above: 1. Type of Equipment (Model Name): On License and Product 2. Certification No.: On RRL certificate. Obtain certificate from local Intel representative 3. Name of Certification Recipient: Intel Corporation 4. Date of Manufacturer: Refer to date code on product 5.
Product Ecology Change (EU RoHS) Intel has a system in place to restrict the use of banned substances in accordance with the European Directive 2002/95/EC. Compliance is based on declaration that materials banned in the RoHS Directive are either (1) below all applicable threshold limits or (2) an approved / pending RoHS exemption applies.
Page 79
CRoHS Substance Tables China CRoHS requires products to be provided with controlled substance information. Intel understands the end-seller (entity placing product into market place) is responsible for providing the controlled substance information. Controlled substance information is required to be in Simplified Chinese. Substance table for this board product is as follows: ®...
The State of California requires a warning to be included for products containing a device using Lithium Perchlorate. Intel understands CA Lithium Perchlorate require a printed warning to be included with all products containing a Lithium battery, either as an insert, in existing product literature, or as part of the shipping memo wording.
Telephone All calls are billed per incident, levied in local currency at the applicable credit card exchange rate plus applicable taxes. (Intel reserves the right to change the pricing for telephone support at any time without notice). Before calling, fill out an “System Issue Report...
Brazil ..001-916 377 0180 Chile Easter Island....Contact AT&T USA at 800 800 311. Once connected, dial 800 843 4481 Mainland and Juan .. Contact AT&T USA at 800 225 288. Once connected, dial 800 843 4481 ® Intel Workstation Board S5000XVN...
Page 83
Panama..Contact AT&T USA at 00 800 001 0109. Once connected, dial 800 843 4481 Paraguay ... 001 916 377 0114 Peru ... 001 916 377 0114 Uruguay..001 916 377 0114 Venezuela... Contact AT&T USA at 0 800 2255 288. Once connected, dial 800 843 4481 ® Intel Workstation Board S5000XVN...
Appendix D: System Issue Report Form Note: An on-line / automatic submission version of this form is available at http:// support.intel.com/support/motherboards/server/S5000XVN/. For the fastest service, please submit your form via the Internet. Date Submitted: _______________________________________________________ Company Name: ______________________________________________________ Contact Name: ________________________________________________________...
Page 86
Check each box below as applicable, and provide the requested information. Driver I/O Base Peripheral Description Revision Address Revision Add-in Card Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Video Add-in video On-board NIC1 On-board NIC2 ® Intel Workstation Board S5000XVN...
Page 87
Hard Drive Information Drive Type (SATA, Hot-swap Make/Model SAS, etc.) or Fixed Revision Control Panel Information Standard Control Panel _________________________________________________ ® Intel Local Control Panel_______________________________________________ ® Intel Workstation Board S5000XVN...
Page 88
Please also include any details on troubleshooting already done. ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ® Intel Workstation Board S5000XVN...