IBM 88643RU - System x3850 - 8864 Service Manual page 162

v Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
v See Chapter 3, "Parts listing, Type 8864," on page 23 to determine which components are customer
replaceable units (CRU) and which components are field replaceable units (FRU).
v If an action step is preceded by "(Trained service technician only)", that step must be performed only by a
trained service technician.
Error message
Received split completion error on PCI primary
Chassis#=X Slot#=Y Bus#=Z Dev.ID=0xSSSS
Vend.ID=0xTTTT Status=0xUUUU
DevFun#=0xVV
PCI-PCI bridge secondary: Address of special
cycle DPE Chassis#=X Slot#=Y Bus#=Z
Dev.ID=0xSSSS Vend.ID=0xTTTT
Status=0xUUUU DevFun#=0xVV
PCI-PCI bridge secondary: Master read parity
error Chassis#=X Slot#=Y Bus#=Z
Dev.ID=0xSSSS Vend.ID=0xTTTT
Status=0xUUUU DevFun#=0xVV
PCI-PCI bridge secondary: Received target
parity error Chassis#=X Slot#=Y Bus#=Z
Dev.ID=0xSSSS Vend.ID=0xTTTT
Status=0xUUUU DevFun#=0xVV
PCI-PCI bridge secondary: Master write parity
error Chassis#=X Slot#=Y Bus#=Z
Dev.ID=0xSSSS Vend.ID=0xTTTT
Status=0xUUUU DevFun#=0xVV
PCI-PCI bridge secondary: Device signaled
SERR Chassis#=X Slot#=Y Bus#=Z
Dev.ID=0xSSSS Vend.ID=0xTTTT
Status=0xUUUU DevFun#=0xVV
PCI-PCI bridge secondary: Slave signaled parity
error. Chassis#=X Slot#=Y Bus#=Z
Dev.ID=0xSSSS Vend.ID=0xTTTT
Status=0xUUUU DevFun#=0xVV
PCI-PCI bridge secondary: Signaled target abort
Chassis#=X Slot#=Y Bus#=Z Dev.ID=0xSSSS
Vend.ID=0xTTTT Status=0xUUUU
DevFun#=0xVV
146
IBM System x3850 Type 8864: Problem Determination and Service Guide
Action
1. If the slot number is greater than 0, complete the following
steps:
a. Reseat the adapter.
b. Replace the adapter.
2. If the slot number is 0, replace the PCI board.
1. If the slot number is greater than 0, complete the following
steps:
a. Reseat the adapter.
b. Replace the adapter.
2. If the slot number is 0, replace the PCI board.
1. If the slot number is greater than 0, complete the following
steps:
a. Reseat the adapter.
b. Replace the adapter.
2. If the slot number is 0, replace the PCI board.
1. If the slot number is greater than 0, complete the following
steps:
a. Reseat the adapter.
b. Replace the adapter.
2. If the slot number is 0, replace the PCI board.
1. If the slot number is greater than 0, complete the following
steps:
a. Reseat the adapter.
b. Replace the adapter.
2. If the slot number is 0, replace the PCI board.
1. If the slot number is greater than 0, complete the following
steps:
a. Reseat the adapter.
b. Replace the adapter.
2. If the slot number is 0, replace the PCI board.
1. If the slot number is greater than 0, complete the following
steps:
a. Reseat the adapter.
b. Replace the adapter.
2. If the slot number is 0, replace the PCI board.
1. If the slot number is greater than 0, complete the following
steps:
a. Reseat the adapter.
b. Replace the adapter.
2. If the slot number is 0, replace the PCI board.