Onkyo HT-S5400 Instruction Manual page 52

If the video source is connected to an HDMI input,
you must assign that input to an input selector, and
your TV must be connected to the HDMI OUT.
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
■
There's no picture from a source connected to
an HDMI IN
Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not guaranteed.
■
The on-screen menus don't appear
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
When the AV receiver doesn't connect TV with
HDMI, onscreen menus are not displayed.
Tuner
■
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn't light
Relocate your antenna.
Move the AV receiver away from your TV or
computer.
Listen to the station in mono.
When listening to an AM station, operating the
remote controller may cause noise.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
Remote Controller
■
The remote controller doesn't work
Before operating this unit, be sure to press
RECEIVER.
Make sure that the batteries are installed with the
correct polarity.
Install new batteries. Don't mix different types of
batteries, or old and new batteries.
Make sure that the remote controller is not too far
away from the AV receiver, and that there's no
obstruction between the remote controller and the
AV receiver's remote control sensor.
Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
If the AV receiver is installed in a rack or cabinet
with colored-glass doors, the remote controller may
not work reliably when the doors are closed.
Make sure you've selected the correct remote
controller mode.
Make sure you've entered the correct remote control
code.
Make sure to set the same ID on both the AV
receiver and remote controller.
En
52
■
Can't control other components
14, 35
If it's an Onkyo component, make sure that the
cable and analog audio cable are connected properly.
—
Connecting only an
Make sure you've selected the correct remote
controller mode.
If you've connected a cassette tape deck, to the
TV/CD IN jack, or an RI Dock to the TV/CD IN or
GAME IN or VCR/DVR IN jacks, for the remote
57
controller to work properly, you must set the display.
If you cannot operate it, you will need to enter the
appropriate remote control code.
To control an Onkyo component that's connected
via , point the remote controller at the AV
—
receiver. Be sure to enter the appropriate remote
control code first.
—
To control an Onkyo component that's not
connected via
component. Be sure to enter the appropriate remote
control code first.
Recording
■
Can't record
—
—
On your recorder, make sure the correct input is
selected.
22
To prevent signal loops and damage to the AV
— receiver, input signals are not fed through to outputs
with the same name (e.g., VCR/DVR IN to
VCR/DVR OUT).
—
—
USB Device Playback
—
■
Can't access the music files on a USB device
Make sure the USB device is plugged in properly.
The AV receiver supports USB devices that support
the USB mass storage device class. However,
playback may not be possible with some USB
—
devices even if they conform to the USB mass
storage device class.
4
USB memory devices with security functions cannot
be played.
4
Others
4
■
Standby power consumption
In the following cases, the power consumption may
— reach up to a maximum of 37 W:
– "HDMI Ctrl (RIHD)" setting is set to "On".
(Depending on the TV status, the AV receiver
will enter Standby mode as usual.)
—
– The "HDMI Through" setting is set to other than
"Off".
10, 48
■
The sound changes when I connect my
headphones
47
When a pair of headphones is connected, the
41
listening mode is set to Stereo, unless it's already set
to Stereo, Mono, or Direct.
cable won't work.
point the remote controller at the
16
10, 48
32
47
47
47
—
—
—
55
21
42
—