THUNDER TIGER TITAN X50 Instruction Manual page 9

Main Rotor-3 /
Bag B
No. Material No. Description
1 BK2511 WASHER,d2xD4.5xW0.8
2 BK0649-2 LINKAGE BALL(B)
3
BK0596-1 MAIN ROTOR PITCH HOUSING
4 BK2214 HARDENED FEATHERING SHAFT
5 BK2572 INNER DAMPER(7mm)
6
BK2573 OUTER DAMPER(7mm)
BK2511
WASHER,d2xD4.5xW0.8
墊圈,d2xD4.5xW0.8
BK0649-2
LINKAGE BALL(B)
內六角連接頭自攻螺絲(B)
BK2525
FLAP COLLAR,d7xD10xW1.5
避震軸環,d7xD10xW1.5
HMC4-8B
SOCKET SCREW M4×8
內六角螺絲M4×8
HMV1370ZZWY
BEARING,d7xD13xW5
滾珠軸承,d7xD13xW5
BK2216
THRUST WASHER,d10xD13xW0.5
止推墊片,d10xD13xW0.5
Diagram for Thrust Bearing Assembly
止推軸承安裝示意圖
Large Internal
Diameter
always goes toward
the Main Rotor Hub
內徑較大的一側，面向
主旋翼中心座組。（內
側）
Checking Tips: >
轉動角度： >
（轉動角度大者，內孔大；轉動角度小者，內孔小）
名稱
墊圈,d2xD4.5xW0.8
內六角連接頭自攻螺絲(B)
主旋翼轉座
強化固定軸
內避震墊圈(7mm)
外避震墊圈(7mm)
1. Secure the Linkage alls to the Main Rotor Grips.
2. Insert the Flap Damper into the Main Rotor Hub.
3. Insert the Feathering Shaft through the Flap Dampers & the Main Rotor Hub with some
amount of silicon oil or Vaseline. Center the Feathering Shaft in the Main Rotor Hub.
4. Apply Locitite on the Socket Screw (M4x 8),and then secure the Main Rotor Grips on the
Feathering Shaft with bearings & washers tightly.
1. 將連桿接頭固定於主旋翼夾座。
2. 將旋翼橫軸避震套環置入主旋翼夾座內。
3. 可塗抹些許矽膠油脂或凡士林於旋翼橫軸避震套環上，以便安裝。
4. 依圖示，組裝金屬主旋翼固定座，使用M4X8內六角螺絲鎖入橫軸時需使用螺絲防鬆膠。
HMX0612
THRUST BEARING,d6xD12xW4.5
止推軸承,d6xD12xW4.5
Small Internal
Diameter
always goes toward
the Blade
內徑較小的一側，面向
主旋翼組（外側）。
-3
Qty No. Material No. Description
2 7 BK2525 FLAP COLLAR,d7xD10xW1.5
2 8 BK0435 WASHER,d4xD11xW1.7
2 9
HMC4-8B SOCKET SCREW M4×8
1 10 HMV1370ZZWY BEARING,d7xD13xW5
2 11 BK2216 THRUST WASHER,d10xD13xW0.5
2 12
HMX0612 THRUST BEARING,d6xD12xW4.5
(4)
(2)
Assemble the main rotor pitch housing as drawing
主旋翼轉座組裝示意圖
(10)
Apply grease
使用潤滑油膏(黃油)
-8-
名稱
避震軸環,d7xD10xW1.5
墊圈,d4xD11xW1.7
內六角螺絲M4×8
滾珠軸承,d7xD13xW5
止推墊片,d10xD13xW0.5
止推軸承,d6xD12xW4.5
(6)
(5)
(7)
(1)
(10)
Completed View
Qty
2
2
2
4
2
2
(3)
(8)
(9)
T22
(11) (12)
組裝完成
Apply threadlocker
使用螺絲防鬆膠