THUNDER TIGER TITAN X50 Instruction Manual page 21

Main Frame Assembly-7 /
Bag H+K
No. Material No. Description
1
HMM3Z NYLON NUT,M3
2 BK0077 COLLAR,d3xD4xW6
3
HMV740ZZY BEARING,d4xD7xW2.5
4
BK0649-2 LINKAGE BALL(B)
5 BK2160-R 120° CONTROL ARM-R
6 BK2160-L
120° CONTROL ARM-L
HMM3Z
NYLON NUT,M3
止鬆螺帽,M3
BK0077
COLLAR,d3xD4xW6
軸環,d3xD4xW6
HMV740ZZY
BEARING,d4xD7xW2.5
滾珠軸承,d4xD7xW2.5
BK0649-2
LINKAGE BALL(B)
內六角連接頭自攻螺絲(B)
HME3-30B
SET SCREW,M3x30
無頭內六角螺絲,M3x30
HMC3-10B
SOCKET SCREW,M3x10
內六角螺絲,M3x10
This hole (Left & Right side both) is
design for 140°Control Arms(PV1409)
此孔位（左右二側）用於140°控制搖臂
（PV1409）
名稱
止鬆螺帽,M3
軸環,d3xD4xW6
滾珠軸承,d4xD7xW2.5
內六角連接頭自攻螺絲(B)
120° 控制搖臂(右)
120° 控制搖臂(左)
Step 1 / 步驟一
Attach the Control Arms onto the Main Frame Set as drawing, and note the difference of
Left & Right Control Arms, please refer the "120L"/ "120R" mark on the arms.
參考圖示將控制搖臂裝上主側板上，請注意左、右邊的控制搖臂不同，請對照控制搖臂上L或R凸字
安裝。
(4)
(1) (2) (3)
(4)
(5) Right side
右側
Step 2
1. Slide the 3 Tail Rod Guides onto the Tail Boom
and space them out evenly as drawing, and then
slide the Tail Boom Clamp onto Tail Boom.
2. Insert the Belt into the Tail Boom. Push the Tail
Boom in to the Tail Boom Bracket all the way to
the end. Refer the drawing and note the
orientation of slot on the Tail Boom.
3. Not fix the 3 Tail Rod Guides and not screw
tighten the Tail Boom Clamp at this step; the
position of these parts may be
adjusted later.
4. Attach the Muffler.
-7
Qty No. Material No. Description
7
2 BK2227 ARM COLLAR
8 HME3-30B SET SCREW,M3x30
2
9
4 BK0859-1 TAIL BOOM,663mm
10
6 BK2559 ROD GUIDE
1 11 HNN2-6B TAPPING SCREW,M2x3
12 BK2159
1 TAIL BOOM Clamp
13
HMC3-10B SOCKET SCREW,M3x10
(8)
(7)
(3)
(10)
(12)
(13)
-20-
名稱
擺臂固定軸環
無頭內六角螺絲,M3x30
尾管,663mm
固定環
墊圈自攻螺絲,M2x3
尾管止檔環
內六角螺絲,M3x10
Left side
(6)
左側
(4)
(4)
(7)
(8)
(3)
21mm
步驟二
1. 將3個固定環穿入尾管，並參考圖示平
均分配距離，然後再穿入尾管止擋環。
2. 將皮帶穿入尾管。將尾管推入尾管固定
座至底，請參考圖示，注意尾管上定位
凹槽方向。
3. 此時暫不需固定固定環及止擋環，以便
後續調整。
4. 安裝排氣管。
(10)
(11)
First tape the belt & insert the
end of the belt as shown, and not
twist the belt at this step.
使用膠帶將皮帶尾端貼合，會使皮帶
容易穿過尾管，並請勿扭轉皮帶。
Must be purchased separately
改裝品需另購
Qty
2
2
1
3
3
1
1
(1)
(3) (2)
(4)
(9)