Connecting A Dvd Player - Aiwa XR-MT1000 Operating Instructions Manual

VIDEO/AUX 5.1 CH INPUT
L
CD DIGITAL OUT
(OPTICAL)
MX
d
DX-NM1OOO
m
~
S;B
WOOFER
Refer to the operating instructions of the connected equipment
for details.
The connecting cords are not supplied. Obtain the necessary
connecting cords.
Consult your local Aiwa dealer for optional equipment.
;p;*~,;.".y,@"-".r, ,,$,,,,,.,,"*,* L&,,"ww#i,,io,, ,.e#,-#.,i#m,7&% m#\,,e.,!@,8.., a,4s,! *w**!k. ,..,, .. ,, .,.. "~-.8 *P4.!~,,.,.,$,!. $*,\.aE*],&%lxb'i#f,
VIDEO/AUX JACKS
The MX-NMTI 000 can input analog sound signals through these
jacks.
Use a cable with RCA phono plugs to connect audio equipment
(turntables, LD players, MD players, VCRs, TV, etc.).
Connect the red plug to VIDEO/AUX R jack, and the white plug
to VIDEO/AUX L jack.
It is recommended that this jack be used "toconnect an MD player.
Use a cable with RCA phono plugs.
Connect the red plug to MD R jack of the MX-NMTIOOO, and the
white plug to MD L jack.
The MX-NMT1 000 can output analog sound signals through
these jacks.
Use a cable with RCA phono plugs to connect audio equipment
with LINE IN (analog input) jacks.
Connect the red plug of a cable to LINE OUT R jack, and the
white plug to LINE OUT L jack.
Do not connect any equipment to LINE OUT jacks and VIDEO{
AUX jacks simultaneously. Otherwise, noise is generated and
malfunction occurs.
Connect optional powered sub woofers with built-in amplifier to
SUB WOOFER jacks of the MX-NMTI1300.
34
ENGLISH
5.1 CH INPUT JACKS
This MX-NMTIOOO can input sound signals from the audio
equipment (DVD player, LD player, etc.) that contains a Dolby
Digital decorder with the 5.1 ch output terminals. Refer to
"CONNECTING A DVD PLAYER" on page 35.
The DX-NM1OOO can output CD digital sound signals through
this jack. Use an optical cable to connect digital audio equipment
(DAT deck, MD recorder, etc.).
Remove the dust cap @ from CD DIGITAL OUT (OPTICAL)
jack. Then, connect an optical cable plug to CD DIGITAL OUT
(OPTICAL) jack
When CD DIGITAL OUT (OPTICAL) jack is
not being used
Attach the supplied dust cap @.
POWER
?
I
To play equipment connected to VIDEO/AUX jacks or
proceed as follows.
MD jacks
1 Press VIDEO/AUX/5.lCH or MD.
To dav the equipment connected to VIDEO/AUX, press
VIDEO/AUX/5.1 CH. "VIDEO appears on the display.
To play the equipment connected to MD, press MD. "MD"
appears on the display.
2
Play the connected equipment.
To change a source name in the display
When VlDEO/AUX/5.1CH is pressed, "VIDEO" is displayed
initially. It can be changed to "AUX or "TV".
With the power on, press POWER while pressing VIDEO/ALfX/
5.1 CH.
Repeat the procedure to select one of the names.
To adjust the sound level of the external source
When the sound level of the external source is much higher or
much lower than that of other function sources, adjust it as follows.
1 Press VIDEO/AUX or MD and play the equipment.
2 Press V or ~ so that the sound level becomes the same
as that of the other function sources.
m
During recording, the sound level can not be adjusted.