Page 1 Prestige 650 Series ADSL Router User's Guide Version 3.40 July 2003...
Page 2 Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others.
Page 3: Federal Communications Commission
4. Consult the dealer or an experienced radio/TV technician for help. Notice 1 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Certifications Refer to the product page at www.zyxel.com. FCC Statement...
Page 4: Zyxel Limited Warranty
ZyXEL shall in no event be held liable for indirect or consequential damages of any kind of character to the purchaser.
Page 5: Customer Support
Brief description of the problem and the steps you took to solve it. METHOD E-MAIL TELEPHONE/FAX WEB SITE/ FTP SITE REGULAR MAIL SUPPORT/SALES LOCATION WORLDWIDE support@zyxel.com.tw +886-3-578-3942 www.zyxel.com ZyXEL Communications Corp., 6 Innovation Road II, Science- www.europe.zyxel.com Based Industrial Park, Hsinchu 300, Taiwan. sales@zyxel.com.tw +886-3-578-2439 ftp.europe.zyxel.com NORTH support@zyxel.com +1-800-255-4101 www.us.zyxel.com AMERICA sales@zyxel.com...
Page 6: Table Of Contents
Prestige 650 Series User’s Guide Table of Contents Copyright................................. ii Federal Communications Commission (FCC) Interference Statement.............iii ZyXEL Limited Warranty ..........................iv Customer Support............................v List of Figures ............................... xii List of Tables ............................... xvii List of Charts ..............................xx Preface ................................xxi Introduction to DSL...........................xxiii...
Page 7 Prestige 650 Series User’s Guide DNS Server Address Assignment ....................4-2 LAN TCP/IP ..........................4-2 Configuring LAN ........................4-4 Chapter 5 Wireless LAN Setup ........................5-1 Wireless LAN Overview......................5-1 Levels of Security ........................5-3 Data Encryption with WEP ......................5-4 Inserting a PCMCIA Wireless LAN Card..................5-4 Configuring Wireless LAN ......................5-4 Configuring MAC Filter......................5-7 802.1x Overview ........................5-9...
Page 8 10.5 Configuring Remote Management...................10-2 Chapter 11 Universal Plug-and-Play (UPnP) ..................11-1 11.1 Universal Plug and Play Overview ..................11-1 11.2 UPnP and ZyXEL ........................11-2 11.3 Installing UPnP in Windows Example..................11-3 11.4 Using UPnP in Windows XP Example ..................11-5 Bandwidth Management ..........................V Chapter 12 Bandwidth Management .......................12-1...
Page 9 Chapter 23 Filter Configuration .......................23-1 23.1 About Filtering .........................23-1 23.2 Configuring a Filter Set for the Prestige 650H and the Prestige 650HW.........23-4 23.3 Configuring a Filter Set for the Prestige 650R and the Prestige 650R-E .........23-6 23.4 Configuring a Filter Rule ......................23-9 23.5 Filter Types and NAT ......................23-16...
Page 10 Prestige 650 Series User’s Guide 24.4 SNMP Traps ..........................24-4 Chapter 25 System Security........................25-1 25.1 System Security Overview.......................25-1 25.2 Creating User Accounts on the Prestige...................25-5 Chapter 26 System Information and Diagnosis..................26-1 26.1 System Maintenance Overview ....................26-1 26.2 System Status...........................26-1 26.3 System Information........................26-3 26.4 Log and Trace ..........................26-5 26.5 Diagnostic ..........................26-8 Chapter 27 Firmware and Configuration File Maintenance ..............27-1...
Page 11 Prestige 650R-11 ADSL Router....................H-2 Prestige 650R-13/-17 ADSL Ethernet Router................H-3 Prestige 650R-31/-33 ADSL over ISDN Router ...............H-4 Prestige 650H-11/-13 ADSL Router with 4-Port Ethernet Switch..........H-5 Prestige 650HW-11/-13 ADSL Router with 4-Port Ethernet Switch/Wireless LAN....H-6 Prestige 650HW-31/-33/-37; Prestige 650H-31/-33/-37 ADSL Router with 4-port Switch/Wireless............................H-7...
Page 12: List Of Figures
Prestige 650 Series User’s Guide List of Figures Figure 1-1 Prestige Internet Access Application.....................1-7 Figure 1-2 Prestige LAN-to-LAN Application ....................1-7 Figure 2-1 Password Screen ...........................2-1 Figure 2-2 Web Configurator SITE MAP Screen ...................2-2 Figure 2-3 Password ............................2-3 Figure 2-4 Example Xmodem Upload......................2-5 Figure 3-1 Wizard Screen 1 ..........................3-3 Figure 3-2 Internet Connection with PPPoE....................3-7 Figure 3-3 Internet Connection with RFC 1483 .....................3-8...
Page 13 Prestige 650 Series User’s Guide Figure 12-2 Subnet-based Bandwidth Management Example ..............12-3 Figure 12-3 Application and Subnet-based Bandwidth Management Example ........... 12-4 Figure 12-4 Bandwidth Allotment Example ....................12-5 Figure 12-5 Maximize Bandwidth Usage Example ..................12-6 Figure 12-6 Bandwidth Borrowing Example ....................12-8 Figure 12-7 Bandwidth Manager: Summary....................
Page 14 Prestige 650 Series User’s Guide Figure 19-4 Sample IP Addresses for a TCP/IP LAN-to-LAN Connection..........19-9 Figure 19-5 Menu 11.5 Remote Node Filter (RFC 1483 or ENET Encapsulation) ........19-10 Figure 19-6 Menu 11.5 Remote Node Filter (PPPoA or PPPoE Encapsulation) ........19-10 Figure 19-7 Internet Security........................19-11 Figure 19-8 Menu 21- Filer Set Configuration (P650H/HW)..............19-12 Figure 19-9 Menu 21.11- WebSet 11 ......................19-12...
Page 15 Prestige 650 Series User’s Guide Figure 23-1 Outgoing Packet Filtering Process ................... 23-2 Figure 23-2 Filter Rule Process........................23-3 Figure 23-3 Menu 21 Filter Set Configuration (P650H/HW) ..............23-4 Figure 23-4 NetBIOS_WAN Filter Rules Summary ..................23-5 Figure 23-5 NetBIOS_LAN Filter Rules Summary..................23-5 Figure 23-6 IGMP Filter Rules Summary ....................
Page 16 Prestige 650 Series User’s Guide Figure 27-5 Backup Configuration Example ....................27-7 Figure 27-6 Successful Backup Confirmation Screen ..................27-7 Figure 27-7 Telnet into Menu 24.6 .......................27-8 Figure 27-8 Restore Using FTP Session Example ..................27-9 Figure 27-9 System Maintenance – Restore Configuration ................27-9 Figure 27-10 System Maintenance –...
Page 17 Prestige 650 Series User’s Guide List of Tables Table 1-1 Model Specific Features......................... 1-2 Table 2-1 Password ............................2-3 Table 3-1 Wizard Screen 1 ..........................3-3 Table 3-2 Internet Connection with PPPoE....................3-7 Table 3-3 Internet Connection with RFC 1483 ....................3-9 Table 3-4 Internet Connection with ENET ENCAP..................
Page 18 Prestige 650 Series User’s Guide Table 13-7 Diagnostic DSL Line ........................13-12 Table 13-8 Firmware Upgrade ........................13-13 Table 14-1 Main Menu Commands ......................14-4 Table 14-2 Main Menu Summary for P650HW....................14-5 Table 15-1 Menu 1 General Setup ........................15-2 Table 15-2 Menu 1.1 Configure Dynamic DNS ...................15-3 Table 16-1 DHCP Ethernet Setup Menu Fields ....................16-3 Table 16-2 TCP/IP Ethernet Setup Menu Fields ...................16-3 Table 17-1 Wireless LAN Setup Field Description..................17-2...
Page 19 Prestige 650 Series User’s Guide Table 28-1 Menu 24.9.1 Budget Management ..................... 28-3 Table 28-2 Menu 24.10 System Maintenance: Time and Date Setting ............28-5 Table 29-1 Menu 24.11 Remote Management Control ................29-2 Table 30-1 Menu 25.1 IP Routing Policy Setup................... 30-3 Table 30-2 Menu 25.1.1 IP Routing Policy....................
Page 20 Prestige 650 Series User’s Guide List of Charts Chart A-1 Troubleshooting Power LED ......................A-1 Chart A-2 Troubleshooting LAN LED ......................A-1 Chart A-3 Troubleshooting DSL LED ......................A-2 Chart A-4 Troubleshooting Console Port.......................A-2 Chart A-5 Troubleshooting Telnet........................A-2 Chart A-6 Troubleshooting Web Configurator....................A-3 Chart A-7 Troubleshooting Internet Browser Display ...................A-4 Chart A-8 Troubleshooting Login Username and Password................A-4 Chart A-9 Troubleshooting LAN Interface ....................A-4...
Page 21: Preface
Compact Guide or Read Me First The Prestige 650H and Prestige 650HW come with a Compact Guide. The Prestige 650R and the Prestige 650R-E use a Read Me First. Both of them are designed to help you get up and running right away.
Page 22 (ADSL over POTS and ADSL over ISDN) unless specifically identified. • The Prestige models with wireless features will be referred to as the Prestige 650H/HW. The following section offers some background information on DSL. Skip to Chapter 1 if you wish to begin working with your router right away.
Page 23: Introduction To Dsl
Prestige 650 Series User’s Guide Introduction to DSL DSL (Digital Subscriber Line) technology enhances the data capacity of the existing twisted-pair wire that runs between the local telephone company switching offices and most homes and offices. While the wire itself can handle higher frequencies, the telephone switching equipment is designed to cut off signals above 4,000 Hz to filter noise off the voice line, but now everybody is searching for ways to get more bandwidth to improve access to the Web - hence DSL technologies.
Page 25: Getting Started
Getting Started Part I: Getting Started This part is structured as a step-by-step guide to help you access your Prestige. It covers key features and applications, accessing the web configurator, password setup and configuring the wizard screens for initial setup.
Page 27: Chapter 1 Getting To Know Your Prestige
The Prestige 650H and Prestige 650HW have an integrated four-port switch with an embedded PCMCIA wireless card slot. The Prestige 650H/HW provides a wireless LAN connectivity allowing users to enjoy the convenience and mobility of working anywhere within the coverage area. The Prestige 650HW includes a wireless LAN card, but the Prestige 650H doesn’t.
Page 28: Table 1-1 Model Specific Features
Prestige 650 Series User’s Guide Table 1-1 Model Specific Features PRESTIGE MODEL P650R P650R-E P650H/HW FEATURES Wireless Slot Wireless LAN Card Four-Port Switch Console Port Auto-crossover 10/100 Mbps Ethernet LAN Reset Button Power Switch IEEE 802.1x Network Security Traffic Redirect Bandwidth Management IP Policy Routing UPnP...
Page 29: Traffic Redirect
Prestige 650 Series User’s Guide PPPoE Support (RFC2516) PPPoE (Point-to-Point Protocol over Ethernet) emulates a dial-up connection. It allows your ISP to use their existing network configuration with newer broadband technologies such as ADSL. The PPPoE driver on the Prestige is transparent to the computers on the LAN, which see only Ethernet and are not aware of PPPoE thus saving you from having to manage PPPoE clients on individual computers.
Page 30: Dynamic Dns Support
Prestige 650 Series User’s Guide Dynamic DNS Support With Dynamic DNS support, you can have a static hostname alias for a dynamic IP address, allowing the host to be more easily accessible from various locations on the Internet. You must register for this service with a Dynamic DNS client.
Page 31: Protocol Support
Prestige 650 Series User’s Guide IP Policy Routing (IPPR) Traditionally, routing is based on the destination address only and the router takes the shortest path to forward a packet. IP Policy Routing (IPPR) provides a mechanism to override the default routing behavior and alter the packet forwarding based on the policy defined by the network administrator.
Page 32: Applications For The Prestige
Prestige 650 Series User’s Guide ♦ CLI (Command Line Interpreter) ♦ Remote SMT session via Telnet ♦ SNMP manageable ♦ Local SMT session via console port ♦ DHCP Server/Client ♦ Built-in Diagnostic Tools ♦ Syslog ♦ TFTP/FTP server, firmware upgrade and configuration backup/support supported Diagnostics Capabilities ♦...
Page 33: Figure 1-1 Prestige Internet Access Application
(for example, T1, OC3, DS3, ATM or Frame Relay). Think of it as the equivalent of a modem rack for ADSL. In addition, for Prestige 650H/HW, you can insert an optional wireless PCMICA card into the Prestige and allow wireless stations access to your network resources. A typical Internet access application is shown below.
Page 35: Chapter 2 Introducing The Web Configurator
Prestige 650 Series User’s Guide Chapter 2 Introducing the Web Configurator This chapter describes how to access and navigate the web configurator. Web Configurator Overview The embedded web configurator allows you to manage the Prestige from anywhere through a browser such as Microsoft Internet Explorer or Netscape Navigator.
Page 36: Navigating The Prestige Web Configurator
Prestige 650 Series User’s Guide Step 6. You should now see the Site Map screen. The Prestige automatically times out after five minutes of inactivity. Simply log back into the Prestige if this happens to you. Navigating the Prestige Web Configurator The following summarizes how to navigate the web configurator from the Site Map screen.
Page 37: Configuring Password
Prestige 650 Series User’s Guide Configuring Password It is highly recommended that you change the password for accessing the Prestige. To change your Prestige’s password, click Advanced Setup and then Password. The screen appears as shown. Figure 2-3 Password The following table describes the labels in this screen. Table 2-1 Password LABEL DESCRIPTION...
Page 38: Resetting The Prestige
Prestige restarts. 2.5.2 Uploading a Configuration File Via Console Port Download the default configuration file from the ZyXEL FTP site, unzip it and save it in a folder. Step 1. Turn off the Prestige, begin a terminal emulation software session and turn on the Prestige again.
Page 39: Figure 2-4 Example Xmodem Upload
Prestige 650 Series User’s Guide Type the configuration file’s location, or click Browse to search for it. Choose the Xmodem protocol. Then click Send. Figure 2-4 Example Xmodem Upload Step 5. After successful firmware upload, enter "atgo" to restart the router. Introducing the Web Configurator...
Page 41: Chapter 3 Wizard Setup
Prestige 650 Series User’s Guide Chapter 3 Wizard Setup This chapter provides information on the Wizard Setup screens in the web configurator. Wizard Setup Introduction Use the Wizard Setup screens to configure your system for Internet access settings and fill in the fields with the information in the Internet Account Information table of the Compact Guide or Read Me First.
Page 42: Multiplexing
Prestige 650 Series User’s Guide 3.2.4 RFC 1483 RFC 1483 describes two methods for Multiprotocol Encapsulation over ATM Adaptation Layer 5 (AAL5). The first method allows multiplexing of multiple protocols over a single ATM virtual circuit (LLC-based multiplexing) and the second method assumes that each protocol is carried over a separate ATM virtual circuit (VC-based multiplexing).
Page 43: Figure 3-1 Wizard Screen 1
Prestige 650 Series User’s Guide Figure 3-1 Wizard Screen 1 The following table describes the labels in this screen. Table 3-1 Wizard Screen 1 LABEL DESCRIPTION Mode From the Mode drop-down list box, select Routing (default) if your ISP allows multiple computers to share an Internet account.
Page 44: Ip Address And Subnet Mask
Prestige 650 Series User’s Guide Table 3-1 Wizard Screen 1 LABEL DESCRIPTION Next Click this button to go to the next wizard screen. The next wizard screen you see depends on what protocol you chose above. Click on the protocol link to see the next wizard screen for that protocol.
Page 45: Ip Assignment With Pppoa Or Pppoe Encapsulation
Prestige 650 Series User’s Guide 3.7.1 IP Assignment with PPPoA or PPPoE Encapsulation If you have a dynamic IP, then the IP Address and ENET ENCAP Gateway fields are not applicable (N/A). If you have a static IP, then you only need to fill in the IP Address field and not the ENET ENCAP Gateway field.
Page 46: Nailed-Up Connection (Ppp)
Prestige 650 Series User’s Guide Nailed-Up Connection (PPP) A nailed-up connection is a dial-up line where the connection is always up regardless of traffic demand. The Prestige does two things when you specify a nailed-up connection. The first is that idle timeout is disabled. The second is that the Prestige will try to bring up the connection when turned on and whenever the connection is down.
Page 47: Figure 3-2 Internet Connection With Pppoe
Prestige 650 Series User’s Guide Figure 3-2 Internet Connection with PPPoE The following table describes the labels in this screen. Table 3-2 Internet Connection with PPPoE LABEL DESCRIPTION Service Name Type the name of your PPPoE service here. User Name Configure User Name and Password fields for PPPoA and PPPoE encapsulation only.
Page 48: Figure 3-3 Internet Connection With Rfc 1483
Prestige 650 Series User’s Guide Table 3-2 Internet Connection with PPPoE LABEL DESCRIPTION Connection Select Connect on Demand when you don't want the connection up all the time and specify an idle time-out (in seconds) in the Max. Idle Timeout field. The default setting selects Connection on Demand with 0 as the idle time-out, which means the Internet session will not timeout.
Page 49: Figure 3-4 Internet Connection With Enet Encap
Prestige 650 Series User’s Guide Table 3-3 Internet Connection with RFC 1483 LABEL DESCRIPTION IP Address This field is available if you select Routing in the Mode field. Type your ISP assigned IP address in this field. Network Address Select None, SUA Only or Full Feature from the drop-sown list box. Refer to the NAT Translation chapter for more details.
Page 50: Table 3-4 Internet Connection With Enet Encap
Prestige 650 Series User’s Guide The following table describes the labels in this screen. Table 3-4 Internet Connection with ENET ENCAP LABEL DESCRIPTION IP Address A static IP address is a fixed IP that your ISP gives you. A dynamic IP address is not fixed;...
Page 51: Figure 3-5 Internet Connection With Pppoa
Prestige 650 Series User’s Guide Figure 3-5 Internet Connection with PPPoA The following table describes the labels in this screen. Table 3-5 Internet Connection with PPPoA LABEL DESCRIPTION User Name Enter the user name exactly as your ISP assigned. If assigned a name in the form user@domain where domain identifies a service name, then enter both components exactly as given.
Page 52: Dhcp Setup
Prestige 650 Series User’s Guide Table 3-5 Internet Connection with PPPoA LABEL DESCRIPTION IP Address This option is available if you select Routing in the Mode field. A static IP address is a fixed IP that your ISP gives you. A dynamic IP address is not fixed; the ISP assigns you a different one each time you connect to the Internet.
Page 53: Wizard Setup Configuration: Third Screen
Prestige 650 Series User’s Guide 3.11.1 IP Pool Setup The Prestige is pre-configured with a pool of 32 IP addresses starting from 192.168.1.33 to 192.168.1.64 for the client machines. This leaves 31 IP addresses, 192.168.1.2 to 192.168.1.32 (excluding the Prestige itself which has a default IP of 192.168.1.1) for other server machines, for example, server for mail, FTP, telnet, web, etc., that you may have.
Page 54: Figure 3-7 Wizard : Lan Configuration
Prestige 650 Series User’s Guide Figure 3-7 Wizard : LAN Configuration The following table describes the labels in this screen. Table 3-6 Wizard : LAN Configuration LABEL DESCRIPTION LAN IP Address Enter the IP address of your Prestige in dotted decimal notation, for example, 192.168.1.1 (factory default).
Page 55: Wizard Setup Configuration: Connection Tests
Prestige 650 Series User’s Guide Table 3-6 Wizard : LAN Configuration LABEL DESCRIPTION Client IP Pool Starting This field specifies the first of the contiguous addresses in the IP address pool. Address Size of Client IP Pool This field specifies the size or count of the IP address pool. Primary DNS Server Enter the IP addresses of the DNS servers.
Page 56: Test Your Internet Connection
3.14 Test Your Internet Connection Launch your web browser and navigate to www.zyxel.com. Internet access is just the beginning. Refer to the rest of this User’s Guide for more detailed information on the complete range of Prestige features. If you cannot access the Internet, open the web configurator again to confirm that the Internet settings you configured in the Wizard Setup are correct.
Page 57: Lan, Wireless Lan And Wan
LAN, Wireless LAN and WAN Part II: LAN, Wireless LAN and WAN This part covers the LAN (Local Area Network), wireless LAN and WAN setup.
Page 59: Chapter 4 Lan Setup
DNS (Domain Name System) is for mapping a domain name to its corresponding IP address and vice versa, for example, the IP address of www.zyxel.com is 204.217.0.2. The DNS server is extremely important because without it, you must know the IP address of a machine before you can access it. The DNS server addresses that you enter in the DHCP setup are passed to the client machines along with the assigned IP address and subnet mask.
Page 60: Dns Server Address Assignment
Prestige 650 Series User’s Guide There are two ways that an ISP disseminates the DNS server addresses. The first is for an ISP to tell a customer the DNS server addresses, usually in the form of an information sheet, when s/he signs up. If your ISP gives you the DNS server addresses, enter them in the DNS Server fields in DHCP Setup, otherwise, leave them blank.
Page 61: Rip Setup
Prestige 650 Series User’s Guide These parameters should work for the majority of installations. If your ISP gives you explicit DNS server address(es), read the embedded web configurator help regarding what fields need to be configured. 4.4.2 IP Address and Subnet Mask Refer to the IP Address and Subnet Mask section in the Wizard Setup chapter for this information.
Page 62: Configuring Lan
Prestige 650 Series User’s Guide Configuring LAN Click LAN to open the following screen. Figure 4-2 LAN The following table describes the labels in this screen. Table 4-1 LAN LABEL DESCRIPTION DHCP LAN Setup...
Page 63 Prestige 650 Series User’s Guide Table 4-1 LAN LABEL DESCRIPTION DHCP If set to Server, your Prestige can assign IP addresses, an IP default gateway and DNS servers to Windows 95, Windows NT and other systems that support the DHCP client. If set to None, the DHCP server will be disabled.
Page 65: Chapter 5 Wireless Lan Setup
Wireless LAN Setup This chapter discusses how to configure Wireless LAN on the Prestige. This chapter is only applicable to the Prestige 650H and Prestige 650HW. Wireless LAN Overview This section introduces the wireless LAN and some basic configurations. Wireless LANs can be as simple as...
Page 66: Figure 5-1 Rts/Cts
Prestige 650 Series User’s Guide 5.1.4 RTS/CTS A hidden node occurs when two stations are within range of the same access point, but are not within range of each other. The following figure illustrates a hidden node. Both stations (STA) are within range of the access point (AP) or wireless gateway, but out-of-range of each other, so they cannot “hear”...
Page 67: Levels Of Security
Prestige 650 Series User’s Guide Enabling the RTS Threshold causes redundant network overhead that could negatively affect the throughput performance instead of providing a remedy. 5.1.5 Fragmentation Threshold A Fragmentation Threshold is the maximum data fragment size (between 256 and 2432 bytes) that can be sent in the wireless network before the Prestige will fragment the packet into smaller data frames.
Page 68: Data Encryption With Wep
Prestige 650 Series User’s Guide Data Encryption with WEP WEP encryption scrambles the data transmitted between the wireless stations and the access points to keep network communications private. It encrypts unicast and multicast communications in a network. Both the wireless stations and the access points must use the same WEP key for data encryption and decryption. Your Prestige allows you to configure up to four 64-bit or 128-bit WEP keys but only one key can be enabled at any one time.
Page 69 Prestige 650 Series User’s Guide Figure 5-3 Wireless The following table describes the labels in this screen. Table 5-1 Wireless LABEL DESCRIPTION ESSID The ESSID (Extended Service Set Identification) is a unique name to identify the Prestige in the wireless LAN. Wireless stations associating to the Prestige must have the same ESSID. Enter a descriptive name (up to 32 characters).
Page 70: Table 5-1 Wireless
Prestige 650 Series User’s Guide Table 5-1 Wireless LABEL DESCRIPTION Hide ESSID Select Yes to hide the ESSID in so a station cannot obtain the ESSID through passive scanning. Select No to make the ESSID visible so a station can obtain the ESSID through passive scanning.
Page 71: Configuring Mac Filter
Prestige 650 Series User’s Guide Configuring MAC Filter The MAC filter screen allows you to configure the Prestige to give exclusive access to up to 32 devices (Allow Association) or exclude up to 32 devices from accessing the Prestige (Deny Association). Every Ethernet device has a unique MAC (Media Access Control) address.
Page 72: Figure 5-4 Mac Address Filter
Prestige 650 Series User’s Guide Figure 5-4 MAC Address Filter The following table describes the labels in this menu. Wireless LAN Setup...
Page 73: Overview
Prestige 650 Series User’s Guide Table 5-2 MAC Address Filter LABEL DESCRIPTION Active Select Yes from the drop down list box to enable MAC address filtering. Action Define the filter action for the list of MAC addresses in the MAC address filter table. Select Deny Association to block access to the router, MAC addresses not listed will be allowed to access the router.
Page 74: Eap Authentication Overview
Prestige 650 Series User’s Guide • Access-Request Sent by an access point requesting authentication. • Access-Reject Sent by a RADIUS server rejecting access. • Access-Accept Sent by a RADIUS server allowing access. • Access-Challenge Sent by a RADIUS server requesting more information in order to allow access. The access point sends a proper response from the user and then sends another Access-Request message.
Page 75: Configuring 802.1X
Prestige 650 Series User’s Guide Figure 5-5 EAP Authentication The details below provide a general description of how IEEE 802.1x EAP authentication works. For an example list of EAP-MD5 authentication steps, see the IEEE 802.1x appendix. Step 1. The wireless station sends a “start” message to the Prestige. Step 2.
Page 76: Table 5-3 802.1X
Prestige 650 Series User’s Guide Table 5-3 802.1x LABEL DESCRIPTION Wireless Port To control wireless stations access to the wired network, select a control method from Control the drop-down list box. Choose from No Authentication Required, Authentication Required and No Access Allowed. No Authentication Required allows all wireless stations access to the wired network without entering user names and passwords.
Page 77: Configuring Local User Authentication
Prestige 650 Series User’s Guide Table 5-3 802.1x LABEL DESCRIPTION Authentication This field is activated only when you select Authentication Required in the Wireless Databases Port Control field. The authentication database contains wireless station login information. The local user database is the built-in database on the Prestige. The RADIUS is an external server. Use this drop-down list box to select which database the Prestige should use (first) to authenticate a wireless station.
Page 78: Figure 5-7 Local User Database
Prestige 650 Series User’s Guide Figure 5-7 Local User Database 5-14 Wireless LAN Setup...
Page 79: Configuring Radius
Prestige 650 Series User’s Guide The following table describes the labels in this screen. Table 5-4 Local User Database LABEL DESCRIPTION This is the index number of a local user account. Active Select this check box to enable the user profile. User Name Enter the user name of the user profile.
Page 80: Figure 5-8 Radius
Prestige 650 Series User’s Guide Figure 5-8 RADIUS The following table describes the labels in this screen. Table 5-5 RADIUS LABEL DESCRIPTION Authentication Server Active Select Yes from the drop-down list box to enable user authentication through an external authentication server. Server IP Address Enter the IP address of the external authentication server in dotted decimal notation.
Page 81 Prestige 650 Series User’s Guide Table 5-5 RADIUS LABEL DESCRIPTION Port Number The default port of the RADIUS server for authentication is 1812. You need not change this value unless your network administrator instructs you to do so with additional information. Shared Secret Enter a password (up to 31 alphanumeric characters) as the key to be shared between the external authentication server and the access points.
Page 83: Chapter 6 Wan Setup
Prestige 650 Series User’s Guide Chapter 6 WAN Setup This chapter describes how to configure WAN settings. WAN Overview A WAN (Wide Area Network) is an outside connection to another network or the Internet. See the Wizard Setup chapter for more information on the fields in the WAN screens. PPPoE Encapsulation The Prestige supports PPPoE (Point-to-Point Protocol over Ethernet).
Page 84: Traffic Shaping
Prestige 650 Series User’s Guide Traffic Shaping Traffic Shaping is an agreement between the carrier and the subscriber to regulate the average rate and “burstiness” or fluctuation of data transmission over an ATM network. This agreement helps eliminate congestion, which is important for transmission of real time data such as audio and video connections. Peak Cell Rate (PCR) is the maximum rate at which the sender can send cells.
Page 85: Figure 6-2 Internet Access Setup
Prestige 650 Series User’s Guide Figure 6-2 Internet Access Setup WAN Setup...
Page 86: Table 6-1 Internet Access Setup
Prestige 650 Series User’s Guide The following table describes the labels in this screen. Table 6-1 Internet Access Setup LABEL DESCRIPTION Name Enter the name of your Internet Service Provider, e.g., MyISP. This information is for identification purposes only. Mode Select Routing (default) from the drop-down list box if your ISP allows multiple computers to share an Internet account.
Page 87 Prestige 650 Series User’s Guide Table 6-1 Internet Access Setup LABEL DESCRIPTION Maximum Burst Size Maximum Burst Size (MBS) refers to the maximum number of cells that can be sent at the peak rate. Type the MBS, which is less than 65535. Login Information (PPPoA and PPPoE encapsulation only) Service Name (PPPoE only) Type the name of your PPPoE service here.
Page 88 Prestige 650 Series User’s Guide Table 6-1 Internet Access Setup LABEL DESCRIPTION ENET ENCAP You must specify a gateway IP address (supplied by your ISP) when you select ENET Gateway ENCAP in the Encapsulation field. (ENET ENCAP encapsulation only) Back Click Back to return to the previous screen.
Page 89: Nat, Dynamic Dns And Time Zone
NAT, Dynamic DNS and Time Zone Part III: NAT, Dynamic DNS and Time Zone This part covers NAT (Network Address Translation), dynamic DNS (Domain Name Sever) and Time Zone setup.
Page 91: Chapter 7 Network Address Translation (Nat)
Prestige 650 Series User’s Guide Chapter 7 Network Address Translation (NAT) This chapter discusses how to configure NAT on the Prestige. NAT Overview NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet, for example, the source address of an outgoing packet, used within one network to a different IP address known within another network.
Page 92: Figure 7-1 How Nat Works
Prestige 650 Series User’s Guide local address before forwarding it to the original inside host. Note that the IP address (either local or global) of an outside host is never changed. The global IP addresses for the inside hosts can be either static or dynamically assigned by the ISP. In addition, you can designate servers, for example, a web server and a telnet server, on your local network and make them accessible to the outside world.
Page 93: Figure 7-2 Nat Application With Ip Alias
2. Many to One: In Many-to-One mode, the Prestige maps multiple local IP addresses to one global IP address. This is equivalent to SUA (for instance, PAT, port address translation), ZyXEL’s Single User Account feature that previous ZyXEL routers supported (the SUA Only option in today’s routers).
Page 94: Sua (Single User Account) Versus Nat
Prestige 650 Series User’s Guide 4. Many-to-Many No Overload: In Many-to-Many No Overload mode, the Prestige maps each local IP address to a unique global IP address. 5. Server: This type allows you to specify inside servers of different services behind the NAT to be accessible to the outside world.
Page 95: Sua Server
Prestige 650 Series User’s Guide 1. Choose SUA Only if you have just one public WAN IP address for your Prestige. 2. Choose Full Feature if you have multiple public WAN IP addresses for your Prestige. SUA Server A SUA server set is a list of inside (behind NAT on the LAN) servers, for example, web or FTP, that you can make visible to the outside world even though SUA makes your whole inside network appear as a single computer to the outside world.
Page 96: Table 7-3 Services And Port Numbers
Prestige 650 Series User’s Guide Many residential broadband ISP accounts do not allow you to run any server processes (such as a Web or FTP server) from your location. Your ISP may periodically check for servers and may suspend your account if it discovers any active services at your location.
Page 97: Selecting The Nat Mode
Prestige 650 Series User’s Guide Figure 7-3 Multiple Servers Behind NAT Example Selecting the NAT Mode Click NAT to open the following screen. Figure 7-4 NAT Mode The following table describes the labels in this screen.
Page 98: Configuring Sua Server
Prestige 650 Series User’s Guide Table 7-4 NAT Mode LABEL DESCRIPTION None Select this radio button to disable NAT. Select this radio button if you have just one public WAN IP address for your Prestige. The SUA Only Prestige uses Address Mapping Set 1 in the NAT - Edit SUA/NAT Server Set screen. Edit Details Click this link to go to the NAT - Edit SUA/NAT Server Set screen.
Page 99: Figure 7-5 Edit Sua/Nat Server Set
Prestige 650 Series User’s Guide Figure 7-5 Edit SUA/NAT Server Set The following table describes the labels in this screen. Table 7-5 Edit SUA/NAT Server Set LABEL DESCRIPTION Start Port No. Enter a port number in this field. To forward only one port, enter the port number again in the End Port No. field. To forward a series of ports, enter the start port number here and the end port number in the End Port No.
Page 100: Configuring Address Mapping
Prestige 650 Series User’s Guide Table 7-5 Edit SUA/NAT Server Set LABEL DESCRIPTION End Port No. Enter a port number in this field. To forward only one port, enter the port number again in the Start Port No. field above and then enter it again in this field.
Page 101: Figure 7-6 Address Mapping Rules
Prestige 650 Series User’s Guide Figure 7-6 Address Mapping Rules The following table describes the labels in this screen. Table 7-6 Address Mapping Rules LABEL DESCRIPTION Local Start IP This is the starting Inside Local IP Address (ILA). Local IP addresses are N/A for Server port mapping.
Page 102: Editing An Address Mapping Rule
One-to-one NAT mapping type. M-1: Many-to-One mode maps multiple local IP addresses to one global IP address. This is equivalent to SUA (i.e., PAT, port address translation), ZyXEL's Single User Account feature that previous ZyXEL routers supported only.
Page 103: Table 7-7 Address Mapping Rule Edit
Note that port numbers do not change for One-to-one NAT mapping type. 2. Many-to-One: Many-to-One mode maps multiple local IP addresses to one global IP address. This is equivalent to SUA (i.e., PAT, port address translation), ZyXEL's Single User Account feature that previous ZyXEL routers supported only.
Page 105: Chapter 8 Dynamic Dns Setup
Prestige 650 Series User’s Guide Chapter 8 Dynamic DNS Setup This chapter discusses how to configure your Prestige to use Dynamic DNS. Dynamic DNS Dynamic DNS allows you to update your current dynamic IP address with one or many dynamic DNS services so that anyone can contact you (in NetMeeting, CU-SeeMe, etc.).
Page 106: Figure 8-1 Ddns
Prestige 650 Series User’s Guide Figure 8-1 DDNS The following table describes the labels in this screen. Table 8-1 DDNS LABEL DESCRIPTION Active Select this check box to use dynamic DNS. Service Provider Select the name of your Dynamic DNS service provider. Host Name Type the domain name assigned to your Prestige by your Dynamic DNS provider.
Page 107: Chapter 9 Time And Date Setup
Prestige 650 Series User’s Guide Chapter 9 Time and Date Setup Use this screen to configure the Prestige’s time and date settings. This chapter is not available on all models. Configuring Time Zone To change your Prestige’s time and date, click Time Zone. The screen appears as shown. Use this screen to configure the Prestige’s time based on your local time zone.
Page 108: Table 9-1 Time/Date
Prestige 650 Series User’s Guide The following table describes the labels in this screen. Table 9-1 Time/Date LABEL DESCRIPTION Time Server Use Time Server Select the time service protocol that your time server sends when you turn on the when Bootup Prestige.
Page 109 Prestige 650 Series User’s Guide Table 9-1 Time/Date LABEL DESCRIPTION New Date This field displays the last updated date from the time server. (yyyy-mm-dd) When you select None in the Use Time Server when Bootup field, enter the new date in this field and then click Apply. Time Current Time This field displays the time of your Prestige.
Page 111: Remote Management And Upnp
Remote Management and UPnP Part IV: Remote Management and UPnP This part contains information on how to configure the Prestige for remote management and setting up Universal Plug and Play (UPnP).
Page 113: Chapter 10 Remote Management Configuration
Prestige 650 Series User’s Guide Chapter 10 Remote Management Configuration This chapter provides information on configuring remote management. Remote management is not available on all models 10.1 Remote Management Overview Remote management allows you to determine which services/protocols can access which Prestige interface (if any) from which computers.
Page 114: Telnet
Prestige 650 Series User’s Guide Use the Prestige’s WAN IP address when configuring from the WAN. Use the Prestige’s LAN IP address when configuring from the LAN. 10.1.3 System Timeout There is a system timeout of five minutes (three hundred seconds) for either the console port or telnet/web/FTP connections.
Page 115: Table 10-1 Remote Management
Prestige 650 Series User’s Guide Figure 10-2 Remote Management The following table describes the labels in this screen. Table 10-1 Remote Management LABEL DESCRIPTION Server Type Each of these labels denotes a service that you may use to remotely manage the Prestige. Select the access interface.
Page 117: Chapter 11 Universal Plug-And-Play (Upnp)
Prestige 650 Series User’s Guide Chapter 11 Universal Plug-and-Play (UPnP) This chapter introduces the UPnP feature in the web configurator. 11.1 Universal Plug and Play Overview Universal Plug and Play (UPnP) is a distributed, open networking standard that uses TCP/IP for simple peer- to-peer network connectivity between devices.
Page 118: Upnp And Zyxel
UPnP if this is not your intention. 11.2 UPnP and ZyXEL ZyXEL has achieved UPnP certification from the Universal Plug and Play Forum Creates UPnP™ Implementers Corp. (UIC). ZyXEL's UPnP implementation supports IGD 1.0 (Internet Gateway Device). At the time of writing ZyXEL's UPnP implementation supports Windows Messenger 4.6 and 4.7 while Windows Messenger 5.0 and Xbox are still being tested.
Page 119: Installing Upnp In Windows Example
Prestige 650 Series User’s Guide Table 11-1 Configuring UPnP LABEL DESCRIPTION Enable the Universal Plug Select this checkbox to activate UPnP. Be aware that anyone could use a and Play (UPnP) Service UPnP application to open the web configurator's login screen without entering the Prestige's IP address (although you must still enter the password to access the web configurator).
Page 120: Installing Upnp In Windows Xp
Prestige 650 Series User’s Guide Step 3. In the Communications window, select the Universal Plug and Play check box in the Components selection box. Step 4. Click OK to go back to the Add/Remove Programs Properties window and click Next. Step 5.
Page 121: Using Upnp In Windows Xp Example
Prestige 650 Series User’s Guide Step 5. In the Networking Services window, select the Universal Plug and Play check box. Step 6. Click OK to go back to the Windows Optional Networking Component Wizard window and click Next. 11.4 Using UPnP in Windows XP Example This section shows you how to use the UPnP feature in Windows XP.
Page 122 Prestige 650 Series User’s Guide Step 3. In the Internet Connection Properties Step 4. You may edit or delete the port window, click Settings to see the port mappings or click Add to mappings there were automatically created. manually add port mappings. When the UPnP-enabled device is disconnected from your computer, all port mappings will be deleted automatically.
Page 123: Web Configurator Easy Access
Prestige 650 Series User’s Guide Step 6. Double-click on the icon to display your current Internet connection status. 11.4.2 Web Configurator Easy Access With UPnP, you can access the web-based configurator on the Prestige without finding out the IP address of the Prestige first.
Page 124 Prestige 650 Series User’s Guide Step 4. An icon with the description for each UPnP-enabled device displays under Local Network. Step 5. Right-click on the icon for your Prestige and select Invoke. The web configurator login screen displays. Step 6. Right-click on the icon for your Prestige and select Properties.
Page 125: Bandwidth Management
Bandwidth Management Part V: Bandwidth Management This part provides information on the functions and configuration of Bandwidth Management.
Page 127: Chapter 12 Bandwidth Management
Prestige 650 Series User’s Guide Chapter 12 Bandwidth Management This chapter describes the functions and configuration of bandwidth management. Bandwidth management is not available on all models. 12.1 Bandwidth Management Overview Bandwidth management allows you to allocate an interface’s outgoing capacity to specific types of traffic. It can also help you make sure that the Prestige forwards certain types of traffic (especially real-time applications) with minimum delay.
Page 128: Proportional Bandwidth Allocation
Prestige 650 Series User’s Guide The total of the configured bandwidth budgets for child-classes cannot exceed the configured bandwidth budget speed of the parent class. 12.3 Proportional Bandwidth Allocation Bandwidth management allows you to define how much bandwidth each class gets; however, the actual bandwidth allotted to each class decreases or increases in proportion to actual available bandwidth.
Page 129: Figure 12-2 Subnet-Based Bandwidth Management Example
Prestige 650 Series User’s Guide Figure 12-2 Subnet-based Bandwidth Management Example 12.4.3 Application and Subnet-based Bandwidth Management Example The following example uses bandwidth classes based on LAN subnets and applications (specific applications in each subnet are allotted bandwidth). Table 12-1 Application and Subnet-based Bandwidth Management Example TRAFFIC TYPE FROM SUBNET A FROM SUBNET B...
Page 130: Scheduler
Prestige 650 Series User’s Guide Figure 12-3 Application and Subnet-based Bandwidth Management Example 12.5 Scheduler The scheduler divides up an interface’s bandwidth among the bandwidth classes. The Prestige has two types of scheduler: fairness-based and priority-based. 12.5.1 Priority-based Scheduler With the priority-based scheduler, the Prestige forwards traffic from bandwidth classes according to the priorities that you assign to the bandwidth classes.
Page 131: Figure 12-4 Bandwidth Allotment Example
Prestige 650 Series User’s Guide and on their priority levels. When only one class requires more bandwidth, the Prestige gives extra bandwidth to that class. When multiple classes require more bandwidth, the Prestige gives the highest priority classes the available bandwidth first (as much as they require, if there is enough available bandwidth), and then to lower priority classes if there is still bandwidth available.
Page 132: Figure 12-5 Maximize Bandwidth Usage Example
Prestige 650 Series User’s Guide The following figure shows the bandwidth usage with the maximize bandwidth usage option enabled. The Prestige divides up the unbudgeted 2 Mbps among the classes that require more bandwidth. If the administration department only uses 1 Mbps of the budgeted 2 Mbps, the Prestige also divides the remaining 1 Mbps among the classes that require more bandwidth.
Page 133: Bandwidth Borrowing
Prestige 650 Series User’s Guide 12.7 Bandwidth Borrowing Bandwidth borrowing allows a child-class to borrow unused bandwidth from its parent class, whereas maximize bandwidth usage allows bandwidth classes to borrow any unused or unbudgeted bandwidth on the whole interface. Enable bandwidth borrowing on a child-class to allow the child-class to use its parent class’s unused bandwidth.
Page 134: Figure 12-6 Bandwidth Borrowing Example
Prestige 650 Series User’s Guide Figure 12-6 Bandwidth Borrowing Example The Bill class can borrow unused bandwidth from the Sales USA class because the Bill class has bandwidth borrowing enabled. The Bill class can also borrow unused bandwidth from the Sales class because the Sales USA class also has bandwidth borrowing enabled.
Page 135: Configuring Summary
Prestige 650 Series User’s Guide The Bill class cannot borrow unused bandwidth from the Root class because the Sales class has bandwidth borrowing disabled. The Amy class cannot borrow unused bandwidth from the Sales USA class because the Amy class has bandwidth borrowing disabled.
Page 136: Figure 12-7 Bandwidth Manager: Summary
Prestige 650 Series User’s Guide Figure 12-7 Bandwidth Manager: Summary The following table describes the labels in this screen. Table 12-2 Bandwidth Manager: Summary LABEL DESCRIPTION These read-only labels represent the physical interfaces. WLAN Active Select an interface’s check box to enable bandwidth management on that interface. Not all interfaces are available on every Prestige.
Page 137: Configuring Class Setup
Prestige 650 Series User’s Guide Table 12-2 Bandwidth Manager: Summary LABEL DESCRIPTION Scheduler Select either Priority-Based or Fairness-Based from the drop-down menu to control the traffic flow. Select Priority-Based to give preference to bandwidth classes with higher priorities. Select Fairness-Based to treat all bandwidth classes equally. See section 12.5. Maximize Select this check box to have the Prestige divide up all of the interface’s unallocated Bandwidth...
Page 138: Figure 12-8 Bandwidth Manager: Class Setup
Prestige 650 Series User’s Guide Figure 12-8 Bandwidth Manager: Class Setup The following table describes the labels in this screen. Table 12-3 Bandwidth Manager: Class Setup LABEL DESCRIPTION Interface Select an interface from the drop-down list box for which you wish to set up classes. Back Click Back to go to the main BW Manager screen.
Page 139: Figure 12-9 Bandwidth Manager: Class Configuration
Prestige 650 Series User’s Guide Figure 12-9 Bandwidth Manager: Class Configuration The following table describes the labels in this screen. Table 12-4 Bandwidth Manager: Class Configuration LABEL DESCRIPTION Class Name Use the auto-generated name or enter a descriptive name of up to 20 alphanumeric characters, including spaces.
Page 140 Prestige 650 Series User’s Guide Table 12-4 Bandwidth Manager: Class Configuration LABEL DESCRIPTION Priority Enter a number between 0 and 7 to set the priority of this class. The higher the number, the higher the priority. The default setting is 3. Borrow bandwidth Select this option to allow a child-class to borrow bandwidth from its parent class if from parent class...
Page 141: Table 12-5Services And Port Numbers
Prestige 650 Series User’s Guide Table 12-4 Bandwidth Manager: Class Configuration LABEL DESCRIPTION Cancel Click Cancel to begin configuring this screen afresh. Table 12-5Services and Port Numbers SERVICES PORT NUMBER ECHO FTP (File Transfer Protocol) SMTP (Simple Mail Transfer Protocol) DNS (Domain Name System) Finger HTTP (Hyper Text Transfer protocol or WWW, Web)
Page 142: Figure 12-10 Bandwidth Management Statistics
Prestige 650 Series User’s Guide Figure 12-10 Bandwidth Management Statistics The following table describes the labels in this screen. Table 12-6 Bandwidth Management Statistics LABEL DESCRIPTION Class Name This field displays the name of the class the statistics page is showing. Budget (kbps) This field displays the amount of bandwidth allocated to the class.
Page 143: Configuring Monitor
Prestige 650 Series User’s Guide 12.10 Configuring Monitor To view the Prestige’s bandwidth usage and allotments, click BW Manager, then Monitor. The screen appears as shown. Figure 12-11 Bandwidth Manager Monitor The following table describes the labels in this screen. Table 12-7 Bandwidth Manager Monitor LABEL DESCRIPTION...
Page 145: Maintenance
Maintenance Part VI: Maintenance This part covers the maintenance screens.
Page 147: Chapter 13 Maintenance
Prestige 650 Series User’s Guide Chapter 13 Maintenance This chapter displays system information such as ZyNOS firmware, port IP addresses and port traffic statistics. 13.1 Maintenance Overview Use the maintenance screens to view system information, upload new firmware, manage configuration and restart your Prestige.
Page 148: Figure 13-1 System Status
Prestige 650 Series User’s Guide Figure 13-1 System Status The following table describes the labels in this screen. 13-2 Maintenance...
Page 149: Table 13-1 System Status
System Status System Name This is the name of your Prestige. It is for identification purposes. ZyNOS F/W Version This is the ZyNOS firmware version and the date created. ZyNOS is ZyXEL's proprietary Network Operating System design. DSL FW Version This is the DSL firmware version associated with your Prestige.
Page 150: Figure 13-2 System Status: Show Statistics
Prestige 650 Series User’s Guide Table 13-1 System Status LABEL DESCRIPTION Show Statistics Click Show Statistics to see router performance statistics such as number of packets sent and number of packets received for each port. 13.2.1 System Statistics Click Show Statistics in the System Status screen to open the following screen. Read-only information here includes port status and packet specific statistics.
Page 151: Table 13-2 System Status: Show Statistics
Prestige 650 Series User’s Guide The following table describes the labels in this screen. Table 13-2 System Status: Show Statistics LABEL DESCRIPTION System up Time This is the elapsed time the system has been up. CPU Load This field specifies the percentage of CPU utilization. WAN Port Statistics This is the WAN port.
Page 152: Dhcp Table Screen
Prestige 650 Series User’s Guide Table 13-2 System Status: Show Statistics LABEL DESCRIPTION Collisions This is the number of collisions on this port. Poll Interval(s) Type the time interval for the browser to refresh system statistics. Set Interval Click this button to apply the new poll interval you entered in the Poll Interval field above.
Page 153: Wireless Screens
Prestige 650 Series User’s Guide Table 13-3 DHCP Table LABEL DESCRIPTION Host Name This is the name of the host computer. IP Address This field displays the IP address relative to the Host Name field. This field displays the MAC (Media Access Control) address of the computer with the displayed Address host name.
Page 154: Figure 13-5 Channel Usage Table
Prestige 650 Series User’s Guide Table 13-4 Association List LABEL DESCRIPTION This is the index number of an associated wireless client. MAC Address This field displays the MAC (Media Access Control) address of an associated wireless station. Every Ethernet device has a unique MAC address. The MAC address is assigned at the factory and consists of six pairs of hexadecimal characters, for example, 00:A0:C5:00:00:02.
Page 155: Diagnostic Screens
Prestige 650 Series User’s Guide The following table describes the labels in this screen. Table 13-5 Channel Usage Table LABEL DESCRIPTION Channel This is the index number of the channel. IP Address This field displays Yes if another AP or Ad-hoc network is using the channel within the Prestige’s transmission range.
Page 156: Figure 13-7 Diagnostic General
Prestige 650 Series User’s Guide Figure 13-7 Diagnostic General The following table describes the labels in this screen. Table 13-6 Diagnostic General LABEL DESCRIPTION TCP/IP Type the IP address of a computer that you want to ping in order to test a connection. Address Ping Click this button to ping the IP address that you entered.
Page 157: Figure 13-8 Diagnostic Dsl Line
Prestige 650 Series User’s Guide Table 13-6 Diagnostic General LABEL DESCRIPTION Reset Click this button to reboot the Prestige. A warning dialog box is then displayed asking you if System you're sure you want to reboot the system. Click OK to proceed. Back Click this button to go back to the main Diagnostic screen.
Page 158: Firmware Screen
Click this button to go back to the main Diagnostic screen. 13.6 Firmware Screen Find firmware at www.zyxel.com in a file that (usually) uses the system model name with a "*.bin" extension, e.g., "Prestige.bin". The upload process uses FTP (File Transfer Protocol) and may take up to two minutes.
Page 159: Figure 13-9 Firmware Upgrade
Prestige 650 Series User’s Guide Figure 13-9 Firmware Upgrade The following table describes the labels in this screen. Table 13-8 Firmware Upgrade LABEL DESCRIPTION File Path Type in the location of the file you want to upload in this field or click Browse ... to find it. Browse...
Page 160: Figure 13-10 Network Temporarily Disconnected
Prestige 650 Series User’s Guide The Prestige automatically restarts in this time causing a temporary network disconnect. In some operating systems, you may see the following icon on your desktop. Figure 13-10 Network Temporarily Disconnected After two minutes, log in again and check your new firmware version in the System Status screen. If the upload was not successful, the following screen will appear.
Page 161: Smt General Configuration
SMT General Configuration Part VII: SMT General Configuration This part covers System Management Terminal configuration for general setup, LAN setup, wireless LAN setup, Internet access, remote nodes, remote node TCP/IP, static routing and NAT. See the web configurator parts of this guide for background information on features configurable by web configurator and SMT.
Page 163: Chapter 14 Introducing The Smt
Prestige 650 Series User’s Guide Chapter 14 Introducing the SMT This chapter explains how to access and navigate the System Management Terminal and gives an overview of its menus. 14.1 SMT Introduction The Prestige’s SMT (System Management Terminal) is a menu-driven interface that you can access from a terminal emulator through the console port or over a telnet connection.
Page 164: Figure 14-1 Login Screen
Prestige 650 Series User’s Guide Please note that if there is no activity for longer than five minutes after you log in, your Prestige will automatically log you out. Enter Password : **** Figure 14-1 Login Screen 14.1.4 Prestige SMT Menu Overview We use the Prestige 650HW-31 SMT menus in this guide as an example.
Page 165: Figure 5-3 Wireless
Prestige 650 Series User’s Guide Prestige 650HW Main Menu Menu 3 Menu 1 Menu 4 Menu 12 Menu 14 Menu 15 Menu 11 LAN Setup Internet Access Static Routing Setup Dial-in User Setup General Setup NAT Setup Remote Node Setup Setup Menu 3.1 Menu 14.1...
Page 166: Navigating The Smt Interface
Prestige 650 Series User’s Guide 14.2 Navigating the SMT Interface The SMT (System Management Terminal) is the interface that you use to configure your Prestige. Several operations that you should be familiar with before you attempt to modify the configuration are listed in the table below.
Page 167: Figure 14-3 Smt Main Menu For P650Hw
Static Routing Setup Use this menu to set up static routes. Dial-in User Setup Use this menu to set up local user profiles on the Prestige 650H/HW. NAT Setup Use this menu to specify inside servers when NAT is enabled.
Page 168: Changing The System Password
Prestige 650 Series User’s Guide Table 14-2 Main Menu Summary for P650HW MENU TITLE DESCRIPTION IP Routing Policy Setup Use this menu to configure your IP routing policy. Schedule Setup Use this menu to schedule outgoing calls. Exit Use this to exit from SMT and return to a blank screen. 14.3 Changing the System Password Change the Prestige default password by following the steps shown next.
Page 169: Chapter 15 General Setup
Prestige 650 Series User’s Guide Chapter 15 General Setup Menu 1 - General Setup contains administrative and system-related information. 15.1 General Setup Menu 1 — General Setup contains administrative and system-related information (shown next). The System Name field is for identification purposes. However, because some ISPs check this name you should enter your computer's "Computer Name".
Page 170: Figure 15-1 Menu 1 General Setup
Domain Name Enter the domain name (if you know it) here. If you leave this field zyxel.com.tw blank, the ISP may assign a domain name via DHCP. You can go to menu 24.8 and type "sys domainname" to see the current domain name used by your gateway.
Page 171: Figure 15-2 Menu 1.1 Configure Dynamic Dns
Prestige 650 Series User’s Guide 15.2.1 Configuring Dynamic DNS If you have a private WAN IP address, then you cannot use Dynamic DNS. To configure Dynamic DNS, go to Menu 1 — General Setup and select Yes in the Edit Dynamic DNS field.
Page 173: Chapter 16 Lan Setup
Prestige 650 Series User’s Guide Chapter 16 LAN Setup This chapter covers how to configure your wired Local Area Network (LAN) settings. 16.1 LAN Setup This section describes how to configure the Ethernet using Menu 3 — LAN Setup. From the main menu, enter 3 to display menu 3.
Page 174: Protocol Dependent Ethernet Setup
Prestige 650 Series User’s Guide 16.2 Protocol Dependent Ethernet Setup Depending on the protocols for your applications, you need to configure the respective Ethernet Setup, as outlined below. For TCP/IP Ethernet setup refer to the Internet Access Application chapter. For bridging Ethernet setup refer to the Bridging Setup chapter. 16.3 TCP/IP Ethernet Setup and DHCP Use menu 3.2 to configure your Prestige for TCP/IP.
Page 175: Table 16-1 Dhcp Ethernet Setup Menu Fields
Prestige 650 Series User’s Guide Table 16-1 DHCP Ethernet Setup Menu Fields FIELD DESCRIPTION EXAMPLE DHCP Setup DHCP If set to Server, your Prestige can assign IP addresses, an IP default gateway and DNS servers to Windows 95, Windows NT and other Server systems that support the DHCP client.
Page 176 Prestige 650 Series User’s Guide Table 16-2 TCP/IP Ethernet Setup Menu Fields FIELD DESCRIPTION EXAMPLE Multicast IGMP (Internet Group Multicast Protocol) is a network-layer protocol None used to establish membership in a Multicast group. The Prestige (default) supports both IGMP version 1 (IGMP-v1) and version 2 (IGMP-v2). SPACE BAR] Press the [ to enable IP Multicasting or select None to...
Page 177: Chapter 17 Wireless Lan Setup
Prestige 650 Series User’s Guide Chapter 17 Wireless LAN Setup This chapter covers how to configure wireless LAN settings in SMT menu 3.5. This chapter is only applicable to the Prestige 650 and Prestige 650HW. 17.1 Wireless LAN Overview Refer to the chapter on the wireless LAN screens for wireless LAN background information. 17.2 Inserting a PCMCIA Wireless LAN Card Use a ZyAIR series wireless LAN PCMCIA card to add optional wireless LAN capabilities.
Page 178: Figure 17-1 Menu 3.5 - Wireless Lan Setup
Prestige 650 Series User’s Guide Menu 3.5- Wireless LAN Setup ESSID= Wireless Hide ESSIS = No Channel ID= CH01 2412MHz RTS Threshold= 2432 Frag. Threshold= 2432 WEP= Disable Default Key= N/A Key1= N/A Key2= N/A Key3= N/A Key4= N/A Edit MAC Address Filter= No Press ENTER to Confirm or ESC to Cancel: Figure 17-1 Menu 3.5 - Wireless LAN Setup The following table describes the fields in this menu.
Page 179: Wireless Lan Mac Address Filter
Prestige 650 Series User’s Guide Table 17-1 Wireless LAN Setup Field Description FIELD DESCRIPTION EXAMPLE WEP (Wired Equivalent Privacy) provides data encryption to prevent wireless Disable stations from accessing data transmitted over the wireless network. Select Disable allows wireless stations to communicate with the access points without any data encryption.
Page 180: Figure 17-2 Menu 3.5.1 Wlan Mac Address Filtering
Prestige 650 Series User’s Guide Menu 3.5.1 - WLAN MAC Address Filter Active= No Filter Action= Allowed Association ------------------------------------------------------------------------------ 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00 00:00:00:00:00:00...
Page 181: Chapter 18 Internet Access
Prestige 650 Series User’s Guide Chapter 18 Internet Access This chapter shows you how to configure the LAN and WAN of your Prestige for Internet access 18.1 Internet Access Overview Refer to the chapters on the web configurator’s wizard, LAN and WAN screens for more background information on fields in the SMT screens covered in this chapter.
Page 182: Ip Alias Setup
Prestige 650 Series User’s Guide Figure 18-1 Physical Network Figure 18-2 Partitioned Logical Networks Use menu 3.2.1 to configure IP Alias on your Prestige. 18.4 IP Alias Setup Use menu 3.2 to configure the first network. Move the cursor to Edit IP Alias field and press [SPACEBAR] to choose Yes and press [ENTER] to configure the second and third network.
Page 183: Figure 18-3 Menu 3.2 Tcp/Ip And Dhcp Setup
Prestige 650 Series User’s Guide Menu 3.2 - TCP/IP and DHCP Setup DHCP Setup: DHCP= Server Client IP Pool Starting Addres= 192.168.1.33 Size of Client IP Pool= 32 Primary DNS Server= 0.0.0.0 Secondary DNS Server= 0.0.0.0 Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.168.1.1 IP Subnet Mask= 255.255.255.0...
Page 184: Route Ip Setup
Prestige 650 Series User’s Guide Table 18-1 Menu 3.2.1 IP Alias Setup FIELD DESCRIPTION EXAMPLE IP Alias Choose Yes to configure the LAN network for the Prestige. IP Address Enter the IP address of your Prestige in dotted decimal notation 192.168.1.1 IP Subnet Mask Your Prestige will automatically calculate the subnet mask based on the 255.255.255.0...
Page 185: Internet Access Configuration
Prestige 650 Series User’s Guide 18.6 Internet Access Configuration Menu 4 allows you to enter the Internet Access information in one screen. Menu 4 is actually a simplified setup for one of the remote nodes that you can access in menu 11. Before you configure your Prestige for Internet access, you need to collect your Internet account information.
Page 186 Prestige 650 Series User’s Guide Table 18-2 Menu 4 Internet Access Setup FIELD DESCRIPTION EXAMPLE Multiplexing SPACE BAR LLC-based Press [ ] to select the method of multiplexing used by your ISP. Choices are VC-based or LLC-based. VPI # Enter the Virtual Path Identifier (VPI) assigned to you. VCI # Enter the Virtual Channel Identifier (VCI) assigned to you.
Page 187 Prestige 650 Series User’s Guide Table 18-2 Menu 4 Internet Access Setup FIELD DESCRIPTION EXAMPLE Network Address SPACE BAR SUA Only Press [ ] to select None, SUA Only or Full Translation Feature. Please see the NAT Chapter for more details on the SUA (Single User Account) feature.
Page 189: Chapter 19 Remote Node Configuration
Prestige 650 Series User’s Guide Chapter 19 Remote Node Configuration This chapter covers remote node configuration. 19.1 Remote Node Setup Overview This section describes the protocol-independent parameters for a remote node. A remote node is required for placing calls to a remote gateway. A remote node represents both the remote gateway and the network behind it across a WAN connection.
Page 190: Figure 19-1 Menu 11 Remote Node Setup
Prestige 650 Series User’s Guide Menu 11 - Remote Node Setup 1. My ISP (ISP, SUA) 2. ________ 3. ________ 4. ________ 5. ________ 6. ________ 7. ________ 8. ________ Enter Node # to Edit: Figure 19-1 Menu 11 Remote Node Setup 19.2.2 Encapsulation and Multiplexing Scenarios For Internet access you should use the encapsulation and multiplexing methods used by your ISP.
Page 191: Figure 19-2 Menu 11.1 Remote Node Profile
Prestige 650 Series User’s Guide Menu 11.1 - Remote Node Profile Edit IP/Bridge Options Rem Node Name= MyISP Route= IP in menu 11.3. Active= Yes Bridge= No Encapsulation= ENET ENCAP Edit IP/Bridge= No Multiplexing= LLC-based Edit ATM Options= No Edit ATM Options in Service Name= N/A Incoming: Telco Option:...
Page 192 Prestige 650 Series User’s Guide Table 19-1 Menu 11.1 Remote Node Profile FIELD DESCRIPTION EXAMPLE Rem Login Type the login name that this remote node will use to call your Prestige. The login name and the Rem Password will be used to authenticate this node.
Page 193: Metric
Prestige 650 Series User’s Guide Table 19-1 Menu 11.1 Remote Node Profile FIELD DESCRIPTION EXAMPLE Schedule Sets This field is only applicable for PPPoE and PPPoA encapsulation. You can apply up to four schedule sets here. For more details please refer to the Call Scheduling chapter.
Page 194: Remote Node Network Layer Options
Prestige 650 Series User’s Guide minimum of "1" for directly connected networks. The number must be between "1" and "15"; a number greater than "15" means the link is down. The smaller the number, the lower the "cost". The metric sets the priority for the Prestige’s routes to the Internet. If any two of the default routes have the same metric, the Prestige uses the following pre-defined priorities: 1.
Page 195: Figure 19-3 Menu 11.3 Remote Node Network Layer Options
Prestige 650 Series User’s Guide Menu 11.3 - Remote Node Network Layer Options IP Options: Bridge Options: IP Address Assignment= Dynamic Ethernet Addr Timeout (min)= N/A Rem IP Addr: 0.0.0.0 Rem Subnet Mask= 0.0.0.0 My WAN Addr= 0.0.0.0 NAT= Full Feature Address Mapping Set= 2 Metric= 2 Private= No...
Page 196: My Wan Addr Sample Ip Addresses
Prestige 650 Series User’s Guide Table 19-2 Menu 11.3 Remote Node Network Layer Options FIELD DESCRIPTION EXAMPLE Address When Full Feature is selected in the NAT field, configure address Mapping Set mapping sets in menu 15.1. Select one of the NAT server sets (2-10) in menu 15.2 (see the NAT chapter for details) and type that number here.
Page 197: Remote Node Filter
Prestige 650 Series User’s Guide Figure 19-4 Sample IP Addresses for a TCP/IP LAN-to-LAN Connection 19.5 Remote Node Filter Move the cursor to the Edit Filter Sets field in menu 11.1, then press [SPACE BAR] to select Yes. Press [ENTER] to display Menu 11.5 – Remote Node Filter. Use Menu 11.5 –...
Page 198: Figure 19-5 Menu 11.5 Remote Node Filter (Rfc 1483 Or Enet Encapsulation)
Prestige 650 Series User’s Guide Menu 11.5 - Remote Node Filter Input Filter Sets: protocol filters= 11, 12 device filters= Output Filter Sets: protocol filters= device filters= Enter here to CONFIRM or ESC to CANCEL: Figure 19-5 Menu 11.5 Remote Node Filter (RFC 1483 or ENET Encapsulation) Menu 11.5 - Remote Node Filter Input Filter Sets: protocol filters= 11, 12...
Page 199: Figure 19-7 Internet Security
Prestige 650 Series User’s Guide Figure 19-7 Internet Security Once you apply the filter rules in the web configurator, filter sets 11 and 12 are automatically applied in the protocol filters field under Input Filter Sets in SMT menu 11.5. SMT input protocol filter set numbers that were previously applied are erased after you apply the Internet Security filter rules in the web configurator.
Page 200: Figure 19-8 Menu 21- Filer Set Configuration (P650H/Hw)
Prestige 650 Series User’s Guide Menu 21 - Filter Set Configuration Filter Filter Set # Comments Set # Comments ------ ----------------- ------ ----------------- _______________ _______________ NetBIOS_WAN _______________ NetBIOS_LAN _______________ IGMP _______________ _______________ WebSet1 _______________ WebSet2 Enter Filter Set Number to Configure= 0 Figure 19-8 Menu 21- Filer Set Configuration (P650H/HW) The following figures display the filter rules in filter sets 11 and 12.
Page 201: Editing Atm Layer Options
Prestige 650 Series User’s Guide Do not edit filter sets 11 and 12. They are used exclusively by the web configurator. Any rules you configured in sets 11 and 12 will be erased and replaced when you apply the web configurator-generated filter rules. 19.6 Editing ATM Layer Options Follow the steps shown next to edit Menu 11.6 –...
Page 202: Traffic Redirect
Prestige 650 Series User’s Guide Menu 11.6 - Remote Node ATM Layer Options VPI/VCI (LLC-Multiplexing or PPP-Encapsulation) Only one set of VPI VPI #= 8 and VCI numbers VCI #= 35 ATM QoS Type= UBR needs to be Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 specified.
Page 203: Figure 19-14 Menu 11.1 - Remote Node Profile
Prestige 650 Series User’s Guide To configure the parameters for traffic redirect, enter 11 from the main menu to display Menu 11.1– Remote Node Profile as shown next. Menu 11.1 - Remote Node Profile Rem Node Name= MyISP Route= IP Active= Yes Bridge= No Encapsulation= ENET ENCAP...
Page 204: Figure 19-15 Menu 11.7 Traffic Redirect Setup
Prestige 650 Series User’s Guide Menu 11.7 - Traffic Redirect Setup Active= No Configuration: Backup Gateway IP Address= 0.0.0.0 Metric= 15 Press ENTER to Confirm or ESC to Cancel: Figure 19-15 Menu 11.7 Traffic Redirect Setup The following table describes the fields in this menu. Table 19-4 Menu 11.7 Traffic Redirect Setup FIELD DESCRIPTION...
Page 205: Chapter 20 Static Route Setup
Prestige 650 Series User’s Guide Chapter 20 Static Route Setup This chapter shows how to setup IP static routes. 20.1 IP Static Route Overview Static routes tell the Prestige routing information that it cannot learn automatically through other means. This can arise in cases where RIP is disabled on the LAN or a remote network is beyond the one that is directly connected to a remote node.
Page 206: Configuring An Ip Static Route
Prestige 650 Series User’s Guide 20.2 Configuring an IP static route Step 1. To configure an IP static route, use Menu 12 – Static Route Setup (shown next). Menu 12 - Static Route Setup 1. IP Static Route 3. Bridge Static Route Please enter selection: Figure 20-2 Menu 12 Static Route Setup Step 2.
Page 207: Figure 20-4 Menu12.1.1 Edit Ip Static Route
Prestige 650 Series User’s Guide Menu 12.1.1 - Edit IP Static Route Route #: 1 Route Name= ? Active= No Destination IP Address= ? IP Subnet Mask= ? Gateway IP Address= ? Metric= 2 Private= No Press ENTER to Confirm or ESC to Cancel: Figure 20-4 Menu12.1.1 Edit IP Static Route The following table describes the fields for Menu 12.1.1 –...
Page 208 Prestige 650 Series User’s Guide Table 20-1 Menu12.1.1 Edit IP Static Route FIELD DESCRIPTION Private This parameter determines if the Prestige will include the route to this remote node in its RIP broadcasts. If set to Yes, this route is kept private and is not included in RIP broadcasts.
Page 209: Chapter 21 Bridging Setup
Prestige 650 Series User’s Guide Chapter 21 Bridging Setup This chapter shows you how to configure the bridging parameters of your Prestige. 21.1 Bridging Overview Bridging bases the forwarding decision on the MAC (Media Access Control), or hardware address, while routing does it on the network layer (IP) address.
Page 210: Figure 21-1 Menu 11.1 Remote Node Profile
Prestige 650 Series User’s Guide Menu 11.1 - Remote Node Profile Rem Node Name= ? Route= IP Bridge= Yes Active= Yes Edit IP/Bridge= Yes Encapsulation= ENET ENCAP Multiplexing= VC-based Edit ATM Options= No Service Name= N/A Incoming: Telco Option: Rem Login= N/A Allocated Budget(min)= N/A Rem Password= N/A Period(hr)= N/A...
Page 211: Figure 21-3 Menu 12.3 Bridge Static Route Setup
Prestige 650 Series User’s Guide Table 21-1 Menu 11.3 Remote Node Network Layer Options : Bridge Fields FIELD DESCRIPTION Bridge (menu 11.1) Make sure this field is set to Yes. Edit IP/Bridge (menu Press [SPACE BAR] to select Yes and press [ENTER] to display menu 11.3. 11.1) Ethernet Addr Timeout Type the time (in minutes) for the Prestige to retain the Ethernet Address...
Page 212: Table 21-2 Menu 12.3.1 Edit Bridge Static Route
Prestige 650 Series User’s Guide The following table describes the Edit Bridge Static Route menu. Table 21-2 Menu 12.3.1 Edit Bridge Static Route FIELD DESCRIPTION Route # This is the route index number you typed in Menu 12.3 – Bridge Static Route Setup. Route Name Type a name for the bridge static route for identification purposes.
Page 213: Chapter 22 Network Address Translation (Nat)
Prestige 650 Series User’s Guide Chapter 22 Network Address Translation (NAT) This chapter discusses how to configure NAT on the Prestige. 22.1 NAT Overview 22.1.1 SUA (Single User Account) Versus NAT SUA (Single User Account) is a ZyNOS implementation of a subset of NAT that supports two types of mapping, Many-to-One and Server.
Page 214: Figure 22-1 Menu 4 Applying Nat For Internet Access
Prestige 650 Series User’s Guide Menu 4 - Internet Access Setup ISP's Name= MyISP Encapsulation= RFC 1483 Multiplexing= LLC-based VPI #= 8 VCI #= 35 ATM QoS Type= UBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 My Login= N/A My Password= N/A ENET ENCAP Gateway= N/A...
Page 215: Nat Setup
Prestige 650 Series User’s Guide Menu 11.3 - Remote Node Network Layer Options IP Options: Bridge Options: IP Address Assignment = Dynamic Ethernet Addr Timeout(min)= N/A Rem IP Addr = 0.0.0.0 Rem Subnet Mask= 0.0.0.0 My WAN Addr= N/A NAT= SUA Only Address Mapping Set= N/A Metric= 2 Private= No...
Page 216: Figure 22-3 Menu 15 Nat Setup
Prestige 650 Series User’s Guide The server set is a list of LAN servers mapped to external ports. To use this set, a server rule must be set up inside the NAT address mapping set. Please see the section on port forwarding in the chapter on NAT web configurator screens for further information on these menus.
Page 217: Figure 22-5 Menu 15.1.255 Sua Address Mapping Rules
Prestige 650 Series User’s Guide Menu 15.1.255 - Address Mapping Rules Set Name= SUA Local Start IP Local End IP Global Start IP Global End IP Type --------------- --------------- --------------- --------------- ------ 0.0.0.0 255.255.255.255 0.0.0.0 0.0.0.0 Server Press ENTER to Confirm or ESC to Cancel: Figure 22-5 Menu 15.1.255 SUA Address Mapping Rules The following table explains the fields in this menu.
Page 218: Figure 22-6 Menu 15.1.1 First Set
Prestige 650 Series User’s Guide Table 22-2 SUA Address Mapping Rules FIELD DESCRIPTION EXAMPLE When you have completed this menu, press [ENTER] at the prompt “Press ENTER to confirm or ESC to cancel” to save your configuration or press [ESC] to cancel and go back to the previous screen. User-Defined Address Mapping Sets Now let’s look at option 1 in menu 15.1.
Page 219: Table 22-3 Menu 15.1.1 First Set
Prestige 650 Series User’s Guide up by that number of empty rules. For example, if you have already configured rules 1 to 6 in your current set and now you configure rule number 9. In the set summary screen, the new rule will be rule 7, not 9. Now if you delete rule 4, rules 5 to 7 will be pushed up by 1 rule, so as old rule 5 becomes rule 4, old rule 6 becomes rule 5 and old rule 7 becomes rule 6.
Page 220: Figure 22-7 Menu 15.1.1.1 Editing/Configuring An Individual Rule In A Set
Prestige 650 Series User’s Guide Menu 15.1.1.1 Address Mapping Rule Type= One-to-One Local IP: Start= = N/A Global IP: Start= 0.0.0.0 = N/A Server Mapping Set= N/A Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 22-7 Menu 15.1.1.1 Editing/Configuring an Individual Rule in a Set The following table explains the fields in this menu.
Page 221: Configuring A Server Behind Nat
Prestige 650 Series User’s Guide Table 22-4 Menu 15.1.1.1 Editing/Configuring an Individual Rule in a Set FIELD DESCRIPTION EXAMPLE Server Only available when Type is set to Server. Type a number from 1 to 10 to Mapping Set choose a server set from menu 15.2. When you have completed this menu, press [ENTER] at the prompt “Press ENTER to confirm or ESC to cancel”...
Page 222: Figure 22-9 Menu 15.2.1 Nat Server Setup
Prestige 650 Series User’s Guide Menu 15.2.1 - NAT Server Setup Rule Start Port No. End Port No. IP Address --------------------------------------------------- Default Default 0.0.0.0 192.168.1.33 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 Press ENTER to Confirm or ESC to Cancel: Figure 22-9 Menu 15.2.1 NAT Server Setup Step 4.
Page 223: General Nat Examples
Prestige 650 Series User’s Guide Figure 22-10 Multiple Servers Behind NAT Example 22.5 General NAT Examples The following are some examples of NAT configuration. 22.5.1 Example 1: Internet Access Only In the following Internet access example, you only need one rule where your ILAs (Inside Local addresses) all map to one dynamic IGA (Inside Global Address) assigned by your ISP.
Page 224: Figure 22-11 Nat Example 1
Prestige 650 Series User’s Guide Figure 22-11 NAT Example 1 Menu 4 - Internet Access Setup ISP's Name= MyISP Encapsulation= RFC 1483 Multiplexing= LLC-based VPI #= 8 VCI #= 35 ATM QoS Type= UBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 My Login= N/A My Password= N/A...
Page 225: Figure 22-13 Nat Example 2
Prestige 650 Series User’s Guide 22.5.2 Example 2: Internet Access with an Inside Server Figure 22-13 NAT Example 2 In this case, you do exactly as above (use the convenient pre-configured SUA Only set) and also go to menu 15.2 to specify the Inside Server behind the NAT as shown in the next figure. Menu 15.2.1 - NAT Server Setup (Used for SUA Only) Rule Start Port No.
Page 226: Figure 22-15 Nat Example 3
Prestige 650 Series User’s Guide 22.5.3 Example 3: Multiple Public IP Addresses With Inside Servers In this example, there are 3 IGAs from our ISP. There are many departments but two have their own FTP server. All departments share the same router. The example will reserve one IGA for each department with an FTP server and all departments use the other IGA.
Page 227: Figure 22-16 Example 3: Menu 11.3
Prestige 650 Series User’s Guide Step 1. In this case you need to configure Address Mapping Set 1 from Menu 15.1 - Address Mapping Sets. Therefore you must choose the Full Feature option from the Network Address Translation field (in menu 4 or menu 11.3) in Figure 22-16. Step 2.
Page 228: Figure 22-17 Example 3: Menu 15.1.1.1
Prestige 650 Series User’s Guide Menu 15.1.1.1 Address Mapping Rule Type= One-to-One Local IP: Start= 192.168.1.10 = N/A Global IP: Start= 10.132.50.1 = N/A Server Mapping Set= N/A Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 22-17 Example 3: Menu 15.1.1.1 Menu 15.1.1 - Address Mapping Rules Set Name= Example3...
Page 229: Figure 22-19 Nat Example 4
Prestige 650 Series User’s Guide Menu 15.2.1 - NAT Server Setup Rule Start Port No. End Port No. IP Address --------------------------------------------------- Default Default 0.0.0.0 192.168.1.21 192.168.1.20 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 Press ENTER to Confirm or ESC to Cancel: Example 3: Menu 15.2.1 22.5.4 Example 4: NAT Unfriendly Application Programs Some applications do not support NAT Mapping using TCP or UDP port address translation.
Page 230: Figure 22-20 Example 4: Menu 15.1.1.1 Address Mapping Rule
Prestige 650 Series User’s Guide Other applications such as some gaming programs are NAT unfriendly because they embed addressing information in the data stream. These applications won’t work through NAT even when using One-to-One and Many-to-Many No Overload mapping types. Follow the steps outlined in example 3 to configure these two menus as follows.
Page 231 SMT Advanced Management Part VIII: SMT Advanced Management This part discusses filtering setup, SNMP, system security, system information and diagnosis, firmware and configuration file maintenance, system maintenance, remote management, IP policy routing and call scheduling. See the web configurator parts of this guide for background information on features configurable by web configurator and SMT.
Page 233: About Filtering
Prestige 650 Series User’s Guide Chapter 23 Filter Configuration This chapter shows you how to create and apply filters. 23.1 About Filtering Your Prestige uses filters to decide whether or not to allow passage of a data packet and/or to make a call. There are two types of filter applications: data filtering and call filtering.
Page 234: Figure 23-1 Outgoing Packet Filtering Process
Prestige 650 Series User’s Guide Call Filtering Active Data match Built-in User-defined match match Outgoing Initiate call default Call Filters Data Packet if line not up Call Filters (if applicable) Send packet and reset Idle Timer Match Match Match Drop Drop packet Drop packet packet...
Page 235: Figure 23-2 Filter Rule Process
Prestige 650 Series User’s Guide Start Packet intoFilter Fetch First Filter Set Filter Set Fetch Next Fetch First Filter Set Filter Rule Fetch Next Filter Rule Next filter Next Filter Set Rule Active? Available? Available? Execute Filter Rule Check Next Rule Forward Drop...
Page 236: Configuring A Filter Set For The Prestige 650H And The Prestige 650Hw
NetBIOS, into a single set and give it a descriptive name. You can configure up to twelve filter sets with six rules in each set, for a total of 72 filter rules in the system. 23.2 Configuring a Filter Set for the Prestige 650H and the Prestige 650HW To configure a filter set, follow the steps shown next.
Page 237: Figure 23-4 Netbios_Wan Filter Rules Summary
Prestige 650 Series User’s Guide Menu 21.2 - Filter Rules Summary # A Type Filter Rules M m n - - ---- --------------------------------------------------------------- - - - 1 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=137 N D N 2 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=138 N D N 3 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=139...
Page 238: Configuring A Filter Set For The Prestige 650R And The Prestige 650R-E
Prestige 650 Series User’s Guide 23.3 Configuring a Filter Set for the Prestige 650R and the Prestige 650R-E To configure a filter set, follow the steps shown next. Step 1. Enter 21 in the main menu to display Menu 21 – Filter Set Configuration. Menu 21 - Filter Set Configuration Filter Filter...
Page 239: Figure 23-8 Telnet_Wan Filter Rules Summary
Prestige 650 Series User’s Guide Menu 21.3 - Filter Rules Summary # A Type Filter Rules M m n - - ---- --------------------------------------------------------------- - - - 1 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=23 N D F Enter Filter Rule Number (1-6) to Configure: Figure 23-8 TELNET_WAN Filter Rules Summary Menu 21.4 - Filter Rules Summary # A Type...
Page 240: Table 23-1 Abbreviations Used In The Filter Rules Summary Menu
Prestige 650 Series User’s Guide 23.3.1 Filter Rules Summary Menus The following tables briefly describe the abbreviations used in menu 21.x. Table 23-1 Abbreviations Used in the Filter Rules Summary Menu FIELD DESCRIPTION The filter rule number: 1 to 6. Active: “Y”...
Page 241: Configuring A Filter Rule
Prestige 650 Series User’s Guide Table 23-2 Rule Abbreviations Used FILTER TYPE DESCRIPTION Offset Length 23.4 Configuring a Filter Rule To configure a filter rule, type its number in Menu 21.x – Filter Rules Summary and press [ENTER] to open menu 21.x.1 for the rule. There are two types of filter rules: TCP/IP and Generic.
Page 242: Figure 23-11 Menu 21.X.1 Tcp/Ip Filter Rule
Prestige 650 Series User’s Guide Menu 21.1.1 - TCP/IP Filter Rule Filter #: 1,1 Filter Type= TCP/IP Filter Rule Active= No IP Protocol= 0 IP Source Route= No Destination: IP Addr= IP Mask= Port #= Port # Comp= None Source: IP Addr= IP Mask= Port #= Port # Comp= None...
Page 243 Prestige 650 Series User’s Guide Table 23-3 Menu 21.x.1 TCP/IP Filter Rule FIELD DESCRIPTION EXAMPLE IP Mask Type the IP mask to apply to the Destination: IP Addr IP mask field. Port # Type the destination port of the packets you want to filter. 0 to 65535 The field range is 0 to 65535.
Page 244 Prestige 650 Series User’s Guide Table 23-3 Menu 21.x.1 TCP/IP Filter Rule FIELD DESCRIPTION EXAMPLE Action Not Matched Select the action for a packet not matching the rule. Check Next Rule Choices are Check Next Rule, Forward or Drop. (default) When you have completed this menu, press [ENTER] at the prompt “Press ENTER to confirm or ESC to cancel”...
Page 245: Figure 23-12 Executing An Ip Filter
Prestige 650 Series User’s Guide Packet into IP Filter Filter Active? Apply SrcAddrMask to Src Addr Check Src Not Matched IP Addr Matched Apply DestAddrMask to Dest Addr Check Dest Not Matched IP Addr Matched Check Not Matched IP Protocol Matched Check Src &...
Page 246: Figure 23-13 Menu 21.6.1 Generic Filter Rule
Prestige 650 Series User’s Guide 23.4.2 Generic Filter Rule This section shows you how to configure a generic filter rule. The purpose of generic rules is to allow you to filter non-IP packets. For IP, it is generally easier to use the IP rules directly. For generic rules, the Prestige treats a packet as a byte stream as opposed to an IP packet.
Page 247: Table 23-4 Menu 21.6.1 Generic Filter Rule
Prestige 650 Series User’s Guide Table 23-4 Menu 21.6.1 Generic Filter Rule FIELD DESCRIPTION EXAMPLE Filter # This is the filter set, filter rule coordinates, for instance, 2, 3 refers to the second filter set and the third rule of that set. Filter Type Press [SPACE BAR] and then [ENTER] to select a type of rule.
Page 248: Filter Types And Nat
Prestige 650 Series User’s Guide 23.5 Filter Types and NAT There are two classes of filter rules, Generic Filter Device rules and Protocol Filter (TCP/IP) rules. Generic Filter rules act on the raw data from/to LAN and WAN. Protocol Filter rules act on IP packets. When NAT (Network Address Translation) is enabled, the inside IP address and port number are replaced on a connection-by-connection basis, which makes it impossible to know the exact address and port on the wire.
Page 249: Figure 23-15 Sample Telnet Filter
Prestige 650 Series User’s Guide Figure 23-15 Sample Telnet Filter Step 1. Enter 21 in the main menu to display Menu 21 — Filter Set Configuration. Step 2. Enter the index number of the filter set you want to configure (in this case 6) Step 3.
Page 250: Figure 23-16 Menu 21.6.1 Sample Filter
Prestige 650 Series User’s Guide Step 4. Press [ENTER] at the message Press [ENTER] to confirm or [ESC] to cancel” to open Menu “ 21.6 — Filter Rules Summary. Step 5. Type 1 to configure the first filter rule. Make the entries in this menu as shown next. When you press [ENTER] to confirm, the following screen appears.
Page 251: Applying Filters And Factory Defaults
Prestige 650 Series User’s Guide Menu 21.6 - Filter Rules Summary # A Type Filter Rules M m n - - ---- --------------------------------------------------------------- - - - 1 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=23 N D F Enter Filter Rule Number (1-6) to Configure: 1 This shows you that you have M = N means an action can be taken immediately.
Page 252: Figure 23-18 Filtering Ethernet Traffic
Prestige 650 Series User’s Guide Table 23-5 Filter Sets Table FILTER SETS DESCRIPTION Input Filter Sets: Apply filters for incoming traffic. You may apply protocol or device filter rules. See earlier in this chapter for information on filters. Output Filter Sets: Apply filters for traffic leaving the Prestige.
Page 253: Figure 23-19 Filtering Remote Node Traffic
Prestige 650 Series User’s Guide Apply filter 3 to block Menu 11.5 - Remote Node Filter Tel traffic from the Input Filter Sets: protocol filters= 3 WAN. device filters= Output Filter Sets: protocol filters= 1 device filters= Call Filter Sets: Apply filter 1 to block Protocol filters= Device filters=...
Page 255: Chapter 24 Snmp Configuration
Prestige 650 Series User’s Guide Chapter 24 SNMP Configuration This chapter explains SNMP Configuration menu 22. 24.1 SNMP Overview Simple Network Management Protocol is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. Your Prestige supports SNMP agent functionality, which allows a manager station to manage and monitor the Prestige through the network.
Page 256: Supported Mibs
Trap - Used by the agent to inform the manager of some events. 24.2 Supported MIBs The Prestige supports RFC-1215 and MIB II as defined in RFC-1213 as well as ZyXEL private MIBs. The focus of the MIBs is to let administrators collect statistic data and monitor status and performance.
Page 257: Figure 24-2 Menu 22 Snmp Configuration
Prestige 650 Series User’s Guide Menu 22 - SNMP Configuration SNMP: Get Community= public Set Community= public Trusted Host= 0.0.0.0 Trap: Community= public Destination= 0.0.0.0 Press ENTER to Confirm or ESC to Cancel: Figure 24-2 Menu 22 SNMP Configuration The following table describes the SNMP configuration parameters. Table 24-1 Menu 22 SNMP Configuration FIELD DESCRIPTION...
Page 258: Table 24-2 Snmp Traps
A trap is sent to the manager when receiving any SNMP RFC-1215) get or set requirements with wrong community (password). whyReboot (defined in ZYXEL- A trap is sent with the reason of restart before rebooting MIB) when the system is going to restart (warm start).
Page 259: Chapter 25 System Security
System Security This chapter describes how to configure the system security on the Prestige. This chapter is only applicable to the Prestige 650H and the Prestige 650HW. 25.1 System Security Overview You can configure the system password, an external RADIUS server and IEEE802.1x in menu 23.
Page 260: Figure 25-3 Menu 23.2 System Security : Radius Server
Prestige 650 Series User’s Guide Menu 23.2 - System Security - RADIUS Server Authentication Server: Active= No Server Address= 10.11.12.13 Port #= 1812 Shared Secret= ******** Accounting Server: Active= No Server Address= 10.11.12.13 Port #= 1813 Shared Secret= ******** Press ENTER to Confirm or ESC to Cancel: Figure 25-3 Menu 23.2 System Security : RADIUS Server The following table describes the fields in this menu.
Page 261: Figure 25-4 Menu 23 System Security
Prestige 650 Series User’s Guide Table 25-1 Menu 23.2 System Security : RADIUS Server FIELD DESCRIPTION EXAMPLE Port # The default port of the RADIUS server for accounting is 1813. 1813 You need not change this value unless your network administrator instructs you to do so with additional information.
Page 262: Figure 25-5 Menu 23.4 System Security : Ieee802.1X
Prestige 650 Series User’s Guide Menu 23.4 - System Security - IEEE802.1x Wireless Port Control= Authentication Required ReAuthentication Timer (in second)= 1800 Idle Timeout (in second)= 3600 Authentication Databases= Local User Database Only Press ENTER to Confirm or ESC to Cancel: Figure 25-5 Menu 23.4 System Security : IEEE802.1x The following table describes the fields in this menu.
Page 263: Creating User Accounts On The Prestige
Prestige 650 Series User’s Guide Table 25-2 Menu 23.4 System Security : IEEE802.1x FIELD DESCRIPTION Authentication This field is activated only when you select Authentication Required in the Wireless Port Control field. Databases The authentication database contains wireless station login information. The local user database is the built-in database on the Prestige.
Page 264: Figure 25-6 Menu 14 Dial-In User Setup
Prestige 650 Series User’s Guide Menu 14 - Dial-in User Setup 1. ________ ________ 17. ________ 25. ________ 2. ________ 10. ________ 18. ________ 26. ________ 3. ________ 11. ________ 19. ________ 27. ________ 4. ________ 12. ________ 20. ________ 28.
Page 265: Chapter 26 System Information And Diagnosis
Prestige 650 Series User’s Guide Chapter 26 System Information and Diagnosis This chapter covers the information and diagnostic tools in SMT menus 24.1 to 24.4. 26.1 System Maintenance Overview These tools include updates on system status, port status, log and trace capabilities and upgrades for the system software.
Page 266: Figure 26-2 Menu 24.1 System Maintenance : Status
Prestige 650 Series User’s Guide The following table describes the fields present in Menu 24.1 — System Maintenance — Status which are read-only and meant for diagnostic purposes. Menu 24.1 - System Maintenance – Status hh:mm:ss Sat. Jan. 01, 2000 Node-Lnk Status TxPkts...
Page 267: System Information
Prestige 650 Series User’s Guide Table 26-1 Menu 24.1 System Maintenance : Status FIELD DESCRIPTION My WAN IP This is the IP address of the ISP remote node. (from ISP) Ethernet This shows statistics for the LAN. Status This shows the current status of the LAN. Tx Pkts This is the number of transmitted packets to the LAN.
Page 268: Figure 26-4 Menu 24.2.1 System Maintenance : Information
Menu 1 – General Setup. Routing Refers to the routing protocol used. ZyNOS F/W Version Refers to the ZyNOS (ZyXEL Network Operating System) system firmware version. ZyNOS is a registered trademark of ZyXEL Communications Corporation. ADSL Chipset Vendor Displays the vendor of the ADSL chipset and DSL version.
Page 269: Log And Trace
Prestige 650 Series User’s Guide Table 26-2 Menu 24.2.1 System Maintenance : Information FIELD DESCRIPTION DHCP This field shows the DHCP setting (None, Relay or Server) of the Prestige. 26.3.2 Console Port Speed You can set up different port speeds for the console port through Menu 24.2.2 – System Maintenance – Console Port Speed.
Page 270: Figure 26-6 Menu 24.3 System Maintenance : Log And Trace
Prestige 650 Series User’s Guide Menu 24.3 - System Maintenance - Log and Trace 1. View Error Log 2. UNIX Syslog Please enter selection: Figure 26-6 Menu 24.3 System Maintenance : Log and Trace Step 3. Enter 1 from Menu 24.3 — System Maintenance — Log and Trace to display the error log in the system.
Page 271: Table 26-3 Menu 24.3.2 System Maintenance : Syslog And Accounting
L02 Call Terminated C02 Call Terminated Jul 19 11:19:27 192.168.102.2 ZYXEL: board 0 line 0 channel 0, call 1, C01 Outgoing Call dev=2 ch=0 40002 Jul 19 11:19:32 192.168.102.2 ZYXEL: board 0 line 0 channel 0, call 1, C02 OutCall Connected 64000 40002 Jul 19 11:20:06 192.168.102.2 ZYXEL: board 0 line 0 channel 0, call 1, C02 Call Terminated...
Page 272: Diagnostic
Dst: Destination Address prot: Protocol (“TCP”, ”UDP”, ”ICMP”) spo: Source port dpo: Destination port Jul 19 14:43:55 192.168.102.2 ZYXEL: IP [Src=202.132.154.123 Dst=255.255.255.255 UDP spo=0208 dpo=0208]} S03>R01mF Jul 19 14:44:00 192.168.102.2 ZYXEL: IP [Src=192.168.102.20 Dst=202.132.154.1 UDP spo=05d4 dpo=0035]} S03>R01mF Jul 19 14:44:04 192.168.102.2 ZYXEL: IP [Src=192.168.102.20 Dst=202.132.154.1 UDP spo=05d4 dpo=0035]} S03>R01mF...
Page 273: Figure 26-9 Menu 24.4 System Maintenance : Diagnostic
Prestige 650 Series User’s Guide Menu 24.4 - System Maintenance – Diagnostic xDSL System Reset xDSL 21. Reboot System 22. Command Mode TCP/IP 12. Ping Host Enter Menu Selection Number: Host IP Address= N/A Figure 26-9 Menu 24.4 System Maintenance : Diagnostic The following table describes the diagnostic tests available in menu 24.4 for and the connections.
Page 275: Chapter 27 Firmware And Configuration File Maintenance
The configuration file (often called the romfile or rom-0) contains the factory default settings in the menus such as password, DHCP Setup, TCP/IP Setup, etc. It arrives from ZyXEL with a “rom” filename extension. Once you have customized the Prestige's settings, they can be saved back to your computer under a filename of your choosing.
Page 276: Backup Configuration
Prestige 650 Series User’s Guide Table 27-1 Filename Conventions FILE TYPE INTERNAL NAME EXTERNAL NAME DESCRIPTION Configuration Rom-0 This is the configuration filename on the Prestige. *.rom File Uploading the rom-0 file replaces the entire ROM file system, including your Prestige configurations, system-related data (including the default password), the error log and the trace log.
Page 277: Figure 27-1 Telnet In Menu 24.5
Prestige 650 Series User’s Guide 27.2.1 Backup Configuration Follow the instructions as shown in the next screen. Menu 24.5 - Backup Configuration To transfer the configuration file to your computer, follow the procedure below: 1. Launch the FTP client on your computer. 2.
Page 278: Figure 27-2 Ftp Session Example
331 Enter PASS command Password: 230 Logged in ftp> bin 200 Type I OK ftp> get rom-0 zyxel.rom 200 Port command okay 150 Opening data connection for STOR ras 226 File received OK ftp: 16384 bytes sent in 1.10Seconds 297.89Kbytes/sec.
Page 279: Backup Configuration Using Tftp
Prestige 650 Series User’s Guide 3. The IP address in the Secured Client IP field in menu 24.11 does not match the client IP. If it does not match, the Prestige will disconnect the Telnet session immediately. 4. You have an SMT console session running. 27.2.6 Backup Configuration Using TFTP The Prestige supports the up/downloading of the firmware and the configuration file using TFTP (Trivial File Transfer Protocol) over LAN.
Page 280: Figure 27-3 Menu 24.5 System Maintenance - Backup Configuration
Stop transfer of the file. Refer to section 27.2.5 to read about configurations that disallow TFTP and FTP over WAN. 27.2.9 Backup Via Console Port (only for the Prestige 650H/HW) Back up configuration via console port by following the HyperTerminal procedure shown next. Procedures using other serial communications programs should be similar.
Page 281: Restore Configuration
Prestige 650 Series User’s Guide Step 3. Run the HyperTerminal program by clicking Transfer, then Receive File as shown in the following screen. Type a location for storing the configuration file or click Browse to look for one. Choose the Xmodem protocol. Then click Receive.
Page 282: Figure 27-7 Telnet Into Menu 24.6
Prestige 650 Series User’s Guide WARNING! DO NOT INTERRUPT THE FILE TRANSFER PROCESS AS THIS MAY PERMANENTLY DAMAGE YOUR PRESTIGE. 27.3.1 Restore Using FTP For details about backup using (T)FTP please refer to earlier sections on FTP and TFTP file upload in this chapter.
Page 283: Figure 27-8 Restore Using Ftp Session Example
Figure 27-8 Restore Using FTP Session Example Refer to section 27.2.5 to read about configurations that disallow TFTP and FTP over WAN. 27.3.3 Restore Via Console Port (only for the Prestige 650H/HW) Restore configuration via console port by following the HyperTerminal procedure shown next. Procedures using other serial communications programs should be similar.
Page 284: Uploading Firmware And Configuration Files
Prestige 650 Series User’s Guide Type the configuration file’s location, or click Browse to search for it. Choose the Xmodem protocol. Then click Send. Figure 27-11 Restore Configuration Example Step 4. After a successful restoration you will see the following screen. Press any key to restart the Prestige and return to the SMT menu.
Page 285: Figure 27-13 Telnet Into Menu 24.7.1 Upload System Firmware
Prestige 650 Series User’s Guide Menu 24.7.1 - System Maintenance - Upload System Firmware To upload the system firmware, follow the procedure below: 1. Launch the FTP client on your workstation. 2. Type "open" and the IP address of your system. Then type "root"...
Page 286: Figure 27-15 Ftp Session Example Of Firmware File Upload
Prestige 650 Series User’s Guide Step 2. Enter “open”, followed by a space and the IP address of your Prestige. Step 3. Press [ENTER] when prompted for a username. Step 4. Enter your password as requested (the default is “1234”). Step 5.
Page 287: Tftp Upload Command Example
Commands that you may see in GUI-based TFTP clients are listed earlier in this chapter. 27.4.7 Uploading Via Console Port (only for the Prestige 650H/HW) FTP or TFTP are the preferred methods for uploading firmware to your Prestige. However, in the event of your network being down, uploading files is only possible with a direct connection to your Prestige via the console port.
Page 288: Figure 27-16 Menu 24.7.1 As Seen Using The Console Port
Prestige 650 Series User’s Guide 27.4.8 Uploading Firmware File Via Console Port (only for the Prestige 650H/HW) Step 1. Select 1 from Menu 24.7 – System Maintenance – Upload Firmware to display Menu 24.7.1 – System Maintenance – Upload System Firmware, then follow the instructions as shown in the following screen.
Page 289: Figure 27-18 Menu 24.7.2 As Seen Using The Console Port
Prestige 650 Series User’s Guide After the configuration upload process has completed, restart the Prestige by entering “atgo”. 27.4.10 Uploading Configuration File Via Console Port Step 1. Select 2 from Menu 24.7 – System Maintenance – Upload Firmware to display Menu 24.7.2 –...
Page 290: Figure 27-19 Example Xmodem Upload
Prestige 650 Series User’s Guide Type the configuration file’s location, or click Browse to search for it. Choose the Xmodem protocol. Then click Send. Figure 27-19 Example Xmodem Upload After the configuration upload process has completed, restart the Prestige by entering “atgo”. 27-16 Firmware and Configuration File Maintenance...
Page 291: Chapter 28 System Maintenance
SMT, while adding some low-level setup and diagnostic functions. Enter the CI from the SMT by selecting menu 24.8. See the included disk or the zyxel.com web site for more detailed information on CI commands. Enter 8 from Menu 24 — System Maintenance. A list of valid commands can be found by typing help or ? at the command prompt.
Page 292: Call Control Support
Prestige 650 Series User’s Guide Copyright (c) 1994 - 2003 ZyXEL Communications Corp. ras> ? Valid commands are: exit device ether wlan bridge hdap radius 8021x ras> Figure 28-2 Valid Commands 28.2 Call Control Support Call Control Support is only applicable when Encapsulation is set to PPPoE in menu 4 or menu 11.1.
Page 293: Figure 28-4 Menu 24.9.1 Budget Management
Prestige 650 Series User’s Guide Menu 24.9.1 - Budget Management Remote Node Connection Time/Total Budget Elapsed Time/Total Period 1. MyISP No Budget No Budget 2.-------- 3.-------- 4.-------- 5.-------- 6.-------- 7.-------- 8.-------- Reset Node (0 to update screen): Figure 28-4 Menu 24.9.1 Budget Management The total budget is the time limit on the accumulated time for outgoing calls to a remote node.
Page 294: Figure 28-5 Menu 24 System Maintenance
Prestige 650 Series User’s Guide 28.3 Time and Date Setting The Prestige keeps track of the time and date. There is also a software mechanism to set the time manually or get the current time and date from an external server when you turn on your Prestige. Menu 24.10 allows you to update the time and date settings of your Prestige.
Page 295: Table 28-2 Menu 24.10 System Maintenance: Time And Date Setting
Prestige 650 Series User’s Guide Table 28-2 Menu 24.10 System Maintenance: Time and Date Setting FIELD DESCRIPTION Use Time Server Enter the time service protocol that your time server sends when you turn on the when Bootup Prestige. Not all time servers support all protocols, so you may have to check with your ISP/network administrator or use trial and error to find a protocol that works.
Page 297: Chapter 29 Remote Management
Prestige 650 Series User’s Guide Chapter 29 Remote Management This chapter covers remote management (SMT menu 24.11). Remote management is not available on all models. 29.1 Remote Management Overview Remote management allows you to determine which services/protocols can access which Prestige interface (if any) from which computers.
Page 298: Figure 29-1 Menu 24.11 Remote Management Control
Prestige 650 Series User’s Guide Menu 24.11 - Remote Management Control TELNET Server: Server Port = 23 Server Access = LAN only Secured Client IP = 0.0.0.0 FTP Server: Server Port = 21 Server Access = LAN only Secured Client IP = 0.0.0.0 Web Server: Server Port = 80 Server Access = LAN only...
Page 299: Remote Management And Nat
Prestige 650 Series User’s Guide 29.2.2 Remote Management Limitations Remote management over LAN or WAN will not work when: 1. A filter in menu 3.1 (LAN) or in menu 11.5 (WAN) is applied to block a Telnet, FTP or Web service.
Page 301: Chapter 30 Ip Policy Routing
Prestige 650 Series User’s Guide Chapter 30 IP Policy Routing This chapter covers setting and applying policies used for IP routing. 30.1 IP Policy Routing Overview Traditionally, routing is based on the destination address only and the IAD takes the shortest path to forward a packet.
Page 302: Figure 30-1 Menu 25 Ip Routing Policy Setup
Prestige 650 Series User’s Guide IPPR follows the existing packet filtering facility of RAS in style and in implementation. The policies are divided into sets, where related policies are grouped together. A user defines the policies before applying them to an interface or a remote node, in the same fashion as the filters. There are 12 policy sets with six policies in each set.
Page 303: Figure 30-2 Menu 25.1 Ip Routing Policy Setup
Prestige 650 Series User’s Guide Menu 25.1 - IP Routing Policy Setup Criteria/Action - - -------------------------------------------------------------------------- 1 Y SA=1.1.1.1-1.1.1.1,DA=2.2.2.2-2.2.2.5 SP=20-25,DP=20-25,P=6,T=NM,PR=0 |GW=192.168.1.1,T=MT,PR=0 2 N __________________________________________________________________________ __________________________________________________________________________ 3 N __________________________________________________________________________ __________________________________________________________________________ 4 N __________________________________________________________________________ __________________________________________________________________________ 5 N __________________________________________________________________________ __________________________________________________________________________ 6 N __________________________________________________________________________ __________________________________________________________________________ Enter Policy Rule Number (1-6) to Configure: Figure 30-2 Menu 25.1 IP Routing Policy Setup...
Page 304: Figure 30-3 Menu 25.1.1 Ip Routing Policy
Prestige 650 Series User’s Guide Type a number from 1 to 6 to display Menu 25.1.1 – IP Routing Policy (see the next figure). This menu allows you to configure a policy rule. Menu 25.1.1 - IP Routing Policy Policy Set Name= test Active= Yes Criteria: IP Protocol...
Page 305: Applying An Ip Policy
Prestige 650 Series User’s Guide Table 30-2 Menu 25.1.1 IP Routing Policy FIELD DESCRIPTION Len Comp Press [SPACE BAR] and then [ENTER] to choose from Equal, Not Equal, Less, Greater, Less or Equal or Greater or Equal. Source: addr start / end Source IP address range from start to end.
Page 306: Figure 30-4 Menu 3.2 Tcp/Ip And Dhcp Ethernet Setup
Prestige 650 Series User’s Guide Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP Setup: DHCP= None Client IP Pool Starting Address= N/A Size of Client IP Pool= N/A Primary DNS Server= N/A Secondary DNS Server= N/A Remote DHCP Server= N/A TCP/IP Setup: Type IP IP Address= 192.168.1.1...
Page 307: Ip Policy Routing Example
Prestige 650 Series User’s Guide 30.6 IP Policy Routing Example If a network has both Internet and remote node connections, you can route Web packets to the Internet using one policy and route FTP packets to a remote network using another policy. See the next figure. Figure 30-6 Example of IP Policy Routing To force Web packets coming from clients with IP addresses of 192.168.1.33 to 192.168.1.64 to be routed to the Internet via the WAN port of the Prestige, follow the steps as shown next.
Page 308: Figure 30-7 Ip Routing Policy Example
Prestige 650 Series User’s Guide Step 1. Create a routing policy set in menu 25. Step 2. Create a rule for this set in Menu 25.1.1 — IP Routing Policy as shown next. Menu 25.1.1 - IP Routing Policy Policy Set Name= set1 Active= Yes Criteria: IP Protocol...
Page 309: Figure 30-8 Ip Routing Policy Example
Prestige 650 Series User’s Guide Menu 25.1.1 - IP Routing Policy Policy Set Name= set2 Active= Yes Criteria: IP Protocol Type of Service= Don't Care Packet length= 10 Precedence = Don't Care Len Comp= N/A Source: addr start= 0.0.0.0 end= N/A port start= 0 end= N/A Destination:...
Page 311: Chapter 31 Call Scheduling
Prestige 650 Series User’s Guide Chapter 31 Call Scheduling Call scheduling (applicable for PPPoA or PPPoE encapsulation only) allows you to dictate when a remote node should be called and for how long. 31.1 Call Scheduling Overview The call scheduling feature allows the Prestige to manage a remote node and dictate when a remote node should be called and for how long.
Page 312: Figure 31-2 Menu 26.1 Schedule Set Setup
Prestige 650 Series User’s Guide To delete a schedule set, enter the set number and press [SPACE BAR] and then [ENTER] (or delete) in the Edit Name field. To setup a schedule set, select the schedule set you want to setup from menu 26 (1-12) and press [ENTER] to see Menu 26.1 —...
Page 313 Prestige 650 Series User’s Guide Table 31-1 Menu 26.1 Schedule Set Setup FIELD DESCRIPTION EXAMPLE How Often Should this schedule set recur weekly or be used just once only? Once Press the [SPACE BAR] and then [ENTER] to select Once or Weekly.
Page 314: Figure 31-3 Applying Schedule Set(S) To A Remote Node (Pppoe)
Prestige 650 Series User’s Guide Menu 11.1 - Remote Node Profile Rem Node Name= ChangeMe Route= IP Active= Yes Bridge= No Encapsulation= PPPoE Edit IP/Bridge= No Multiplexing=VC-based Edit ATM Options= No Service Name= Telco Option: Incoming Allocated Budget(min)= 0 Rem Login= Period(hr)= 0 Apply your schedule Rem Password= ********...
Page 315: Appendices And Index
Appendices and Index Part IX: Appendices and Index This part contains troubleshooting, additional background information and an index of key terms.
Page 317: A.1 Using Leds To Diagnose Problems
Prestige 650 Series User’s Guide Appendix A Troubleshooting This chapter covers potential problems and the corresponding remedies. A.1 Using LEDs to Diagnose Problems The LEDs are useful aides for finding possible problem causes. A.1.1 Power LED The PWR LED on the front panel does not light up. Chart A-1 Troubleshooting Power LED STEPS CORRECTIVE ACTION...
Page 318: A.2 Console Port
Prestige 650 Series User’s Guide A.1.3 DSL LED The DSL LED on the front panel does not light up. Chart A-3 Troubleshooting DSL LED STEPS CORRECTIVE ACTION Check the telephone wire and connections between the Prestige DSL port and the wall jack. Make sure that the telephone company has checked your phone line and set it up for DSL service.
Page 319: A.4 Web Configurator
Prestige 650 Series User’s Guide Chart A-5 Troubleshooting Telnet STEPS CORRECTIVE ACTION Make sure you are using the correct IP address of the Prestige. Check the IP address of the Prestige. Ping the Prestige from your computer. If you cannot ping the Prestige, check the IP addresses of the Prestige and your computer. Make sure your computer is set to get a dynamic IP address;...
Page 320: A.5 Login Username And Password
Prestige 650 Series User’s Guide The web configurator does not display properly. Chart A-7 Troubleshooting Internet Browser Display STEPS CORRECTIVE ACTION Make sure you are using Internet Explorer 5.0 and later versions. Delete the temporary web files and log in again. In Internet Explorer, click Tools, Internet Options and then click the Delete Files ...
Page 321: A.7 Wan Interface
Prestige 650 Series User’s Guide Chart A-9 Troubleshooting LAN Interface STEPS CORRECTIVE ACTION Make sure that the IP address and the subnet mask of the Prestige and your computer(s) are on the same subnet. A.7 WAN Interface Initialization of the ADSL connection failed. Chart A-10 Troubleshooting ADSL Connection STEPS CORRECTIVE ACTION...
Page 322: A.9 Remote Management
Prestige 650 Series User’s Guide Chart A-12 Troubleshooting Internet Access STEPS CORRECTIVE ACTION If the DSL LED is off, refer to Section A.1.3. Verify your WAN settings. Refer to the WAN Setup chapter (web configurator) or the Internet Access chapter (SMT). Make sure you entered the correct user name and password.
Page 323: A.10 Remote Node Connection
Prestige 650 Series User’s Guide A.10 Remote Node Connection I cannot connect to a remote node or ISP. Chart A-15 Troubleshooting Connecting to a Remote Node or ISP STEPS CORRECTIVE ACTION Check menu 4 or WAN screen to verify that the username and password are entered properly. In menu 11.1, verify your login name and password for the remote node.
Page 325: Appendix B Ip Subnetting
Prestige 650 Series User’s Guide Appendix B IP Subnetting IP Addressing Routers “route” based on the network number. The router that delivers the data packet to the correct destination host uses the host ID. IP Classes An IP address is made up of four octets (eight bits), written in dotted decimal notation, for example, 192.168.1.1.
Page 326: Chart B-2 Allowed Ip Address Range By Class
Prestige 650 Series User’s Guide A class “A” address (24 host bits) can have 2 –2 hosts (approximately 16 million hosts). Since the first octet of a class “A” IP address must contain a “0”, the first octet of a class “A” address can have a value of 0 to 127.
Page 327: Chart B-4 Alternative Subnet Mask Notation
Prestige 650 Series User’s Guide of ones beginning from the left most bit of the mask, followed by a continuous sequence of zeros, for a total number of 32 bits. Since the mask is always a continuous number of ones beginning from the left, followed by a continuous number of zeros for the remainder of the 32 bit mask, you can simply specify the number of ones instead of writing the value of each octet.
Page 328: Chart B-5 Subnet 1
Prestige 650 Series User’s Guide Divide the network 192.168.1.0 into two separate subnets by converting one of the host ID bits of the IP address to a network number bit. The “borrowed” host ID bit can be either “0” or “1” thus giving two subnets;...
Page 329: Chart B-7 Subnet 1
Prestige 650 Series User’s Guide actual host for the first subnet is 192.168.1.1 and the highest is 192.168.1.126. Similarly the host ID range for the second subnet is 192.168.1.129 to 192.168.1.254. Example: Four Subnets The above example illustrated using a 25-bit subnet mask to divide a class “C” address space into two subnets.
Page 330: Chart B-10 Subnet 4
Prestige 650 Series User’s Guide Chart B-10 Subnet 4 NETWORK NUMBER LAST OCTET BIT VALUE IP Address 192.168.1. IP Address (Binary) 11000000.10101000.00000001. 11000000 Subnet Mask (Binary) 11111111.11111111.11111111. 11000000 Subnet Address: 192.168.1.192 Lowest Host ID: 192.168.1.193 Broadcast Address: 192.168.1.255 Highest Host ID: 192.168.1.254 Example Eight Subnets Similarly use a 27-bit mask to create 8 subnets (001, 010, 011, 100, 101, 110).
Page 331: Chart B-13 Class B Subnet Planning
Prestige 650 Series User’s Guide Chart B-12 Class C Subnet Planning NO. “BORROWED” HOST BITS SUBNET MASK NO. SUBNETS NO. HOSTS PER SUBNET 255.255.255.248 (/29) 255.255.255.252 (/30) 255.255.255.254 (/31) Subnetting With Class A and Class B Networks. For class “A” and class “B” addresses the subnet mask also determines which bits are part of the network number and which are part of the host ID.
Page 332 Prestige 650 Series User’s Guide Chart B-13 Class B Subnet Planning NO. “BORROWED” HOST BITS SUBNET MASK NO. SUBNETS NO. HOSTS PER SUBNET 255.255.255.240 4096 (/28) 255.255.255.248 8192 (/29) 255.255.255.252 16384 (/30) 255.255.255.254 32768 (/31) IP Subnetting...
Page 333 Prestige 650 Series User’s Guide Appendix C Wireless LAN and IEEE 802.11 A wireless LAN (WLAN) provides a flexible data communications system that you can use to access various services (navigating the Internet, email, printer services, etc.) without the any expensive network cabling infrastructure.
Page 334: Infrastructure Wireless Lan Configuration
Prestige 650 Series User’s Guide Ad-hoc Wireless LAN Configuration The simplest WLAN configuration is an independent (Ad-hoc) WLAN that connects a set of computers with wireless nodes or stations (STA), which is called a Basic Service Set (BSS). In the most basic form, a wireless LAN connects a set of computers with wireless adapters.
Page 335 Prestige 650 Series User’s Guide Diagram C-2 ESS Provides Campus-Wide Coverage Wireless LAN and IEEE 802.11...
Page 337: Appendix D Pppoe
Prestige 650 Series User’s Guide Appendix D PPPoE PPPoE in Action An ADSL modem bridges a PPP session over Ethernet (PPP over Ethernet, RFC 2516) from your PC to an ATM PVC (Permanent Virtual Circuit) which connects to a xDSL Access Concentrator where the PPP session terminates (see the next figure).
Page 338 Prestige 650 Series User’s Guide How PPPoE Works The PPPoE driver makes the Ethernet appear as a serial link to the PC and the PC runs PPP over it, while the modem bridges the Ethernet frames to the Access Concentrator (AC). Between the AC and an ISP, the AC is acting as a L2TP (Layer 2 Tunneling Protocol) LAC (L2TP Access Concentrator) and tunnels the PPP frames to the ISP.
Page 339: Virtual Circuit Topology
Prestige 650 Series User’s Guide Appendix E Virtual Circuit Topology ATM is a connection-oriented technology, meaning that it sets up virtual circuits over which end systems communicate. The terminology for virtual circuits is as follows: • Virtual Channel Logical connections between ATM switches •...
Page 341: Appendix F Setting Up Your Computer's Ip Address
Prestige 650 Series User’s Guide Appendix F Setting up Your Computer’s IP Address All computers must have a 10M or 100M Ethernet adapter card and TCP/IP installed. Windows 95/98/Me/NT/2000/XP, Macintosh OS 7 and later operating systems and all versions of UNIX/LINUX include the software components you need to install and use TCP/IP on your computer.
Page 342: Installing Components
Prestige 650 Series User’s Guide Installing Components The Network window Configuration tab displays a list of installed components. You need a network adapter, the TCP/IP protocol and Client for Microsoft Networks. If you need the adapter: In the Network window, click Add. Select Adapter and then click Add.
Page 343 Prestige 650 Series User’s Guide Click the IP Address tab. -If your IP address is dynamic, select Obtain an IP address automatically. -If you have a static IP address, select Specify an IP address and type your information into the IP Address and Subnet Mask fields. Click the DNS Configuration tab.
Page 344: Verifying Settings
Prestige 650 Series User’s Guide Click the Gateway tab. -If you do not know your gateway’s IP address, remove previously installed gateways. -If you have a gateway IP address, type it in the New gateway field and click Add. Click OK to save and close the TCP/IP Properties window. Click OK to close the Network window.
Page 345 Prestige 650 Series User’s Guide Windows 2000/NT/XP For Windows XP, click start, Control Panel. In Windows 2000/NT, click Start, Settings, Control Panel. For Windows XP, click Network Right-click Local Area Connection and Connections. For Windows 2000/NT, click then click Properties. Network and Dial-up Connections.
Page 346 Prestige 650 Series User’s Guide Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click Properties. The Internet Protocol TCP/IP Properties window opens (the General tab in Windows XP). -If you have a dynamic IP address click Obtain an IP address automatically.
Page 347 Prestige 650 Series User’s Guide -If you do not know your gateway's IP address, remove any previously installed gateways in the IP Settings tab and click OK. Do one or more of the following if you want to configure additional IP addresses: -In the IP Settings tab, in IP addresses, click Add.
Page 348 Prestige 650 Series User’s Guide In the Internet Protocol TCP/IP Properties window (the General tab in Windows XP): -Click Obtain DNS server address automatically if you do not know your DNS server IP address(es). -If you know your DNS server IP address(es), click Use the following DNS server addresses, and type them in the Preferred DNS server and Alternate DNS server fields.
Page 349 Prestige 650 Series User’s Guide Macintosh OS 8/9 Click the Apple menu, Control Panel and double-click TCP/IP to open the TCP/IP Control Panel. Select Ethernet built-in from the Connect via list. Setting up Your Computer’s IP Address...
Page 350 Prestige 650 Series User’s Guide For dynamically assigned settings, select Using DHCP Server from the Configure: list. For statically assigned settings, do the following: -From the Configure box, select Manually. -Type your IP address in the IP Address box. -Type your subnet mask in the Subnet mask box. -Type the IP address of your Prestige in the Router address box.
Page 351 Prestige 650 Series User’s Guide Click Network in the icon bar. - Select Automatic from the Location list. - Select Built-in Ethernet from the Show list. - Click the TCP/IP tab. For dynamically assigned settings, select Using DHCP from the Configure list. For statically assigned settings, do the following: -From the Configure box, select Manually.
Page 353: Splitters And Microfilters
Prestige 650 Series User’s Guide Appendix G Splitters and Microfilters This appendix tells you how to install a POTS splitter or a telephone microfilter. Connecting a POTS Splitter When you use the Full Rate (G.dmt) ADSL standard, you can use a POTS (Plain Old Telephone Service) splitter to separate the telephone and ADSL signals.
Page 354 Prestige 650 Series User’s Guide Step 2. Connect a cable from the double jack end of the Y-Connector to the “wall side” of the microfilter. Step 3. Connect another cable from the double jack end of the Y-Connector to the Prestige. Step 4.
Page 355: H.1 Prestige 650R-E1/-E3/-E7 Adsl Router
Prestige 650 Series User’s Guide Appendix H Power Adaptor Specifications H.1 Prestige 650R-E1/-E3/-E7 ADSL Router NORTH AMERICA PLUG STANDARDS AC Power Adapter model DV-121AACS Input power AC120Volts/60Hz/23W max. Output power AC12Volts/1.0A Power consumption Safety standards UL, CUL (UL 1310, CSA C22.2 No.223) NORTH AMERICA PLUG STANDARDS AC Power Adapter model AA-121A...
Page 356: H.2 Prestige 650R-11 Adsl Router
Prestige 650 Series User’s Guide Power consumption Safety standards CCEE (GB8898) EUROPEAN PLUG STANDARDS AC Power Adapter model DV-121AACCP-5716 Input power AC230Volts/50Hz/100mA Output power AC12Volts/1.0A Power consumption Safety standards TUV-GS, CE (EN 60950) EUROPEAN PLUG STANDARDS AC Power Adapter model AA-121ABN Input power AC230Volts/50Hz/140mA...
Page 357: H.3 Prestige 650R-13/-17 Adsl Ethernet Router
Prestige 650 Series User’s Guide CHINESE PLUG STANDARDS AC Power Adapter model DV-121AACCP-5720 Input power AC220Volts/50Hz/18W Output power AC12Volts/1.0A Power consumption 10 W Safety standards CCEE (GB8898) EUROPEAN PLUG STANDARDS AC Power Adapter model DV-121AACUP-5716 Input power AC230Volts/50Hz/19W Output power AC12Volts/1.0A Power consumption Safety standards...
Page 358: H.4 Prestige 650R-31/-33 Adsl Over Isdn Router
Prestige 650 Series User’s Guide Input power AC220Volts/50Hz/18W Output power AC12Volts/1.0A Power consumption 12 W Safety standards CCEE (GB8898) EUROPEAN PLUG STANDARDS AC Power Adapter model AA-121ABN Input power AC230Volts/50Hz/140mA Output power AC12Volts/1.0A Power consumption 12 W Safety standards ITS-GS, CE (EN 60950) H.4 Prestige 650R-31/-33 ADSL over ISDN Router NORTH AMERICA PLUG STANDARDS AC Power Adapter model...
Page 359: H.5 Prestige 650H-11/-13 Adsl Router With 4-Port Ethernet Switch
AA-121AD Input power AC230Volts/50Hz/140mA Output power AC12Volts/1.0A Power consumption Safety standards ITS-GS, CE (EN 60950) H.5 Prestige 650H-11/-13 ADSL Router with 4-Port Ethernet Switch NORTH AMERICA PLUG STANDARDS AC Power Adapter model DV-1215A Input power AC120Volts/60Hz/30W Output power AC 12Volts/ 1.25A...
Page 360: H.6 Prestige 650Hw-11/-13 Adsl Router With 4-Port Ethernet Switch/Wireless Lan
Prestige 650 Series User’s Guide Safety standards UL, CUL, CSA (UL 1310, CSA C22.2 No.223) NORTH AMERICA PLUG STANDARDS AC Power Adapter model AA-121A25 Input power AC120Volts/60Hz/19W Output power AC 12Volts/ 1.25A Power consumption 12 W Safety standards UL, CUL (UL 1310, CSA C22.2 No.223) EUROPEAN PLUG STANDARDS AC Power Adapter model AA-121A3BN...
Page 361: H.7 Prestige 650Hw-31/-33/-37; Prestige 650H-31/-33/-37 Adsl Router With 4-Port Switch/Wireless
Input power AC230Volts/50Hz/140mA Output power AC12Volts/1.3A Power consumption 13 W Safety standards ITS-GS, CE (EN 60950) H.7 Prestige 650HW-31/-33/-37; Prestige 650H-31/-33/-37 ADSL Router with 4-port Switch/Wireless NORTH AMERICA PLUG STANDARDS AC Power Adapter model DV-1215A Input power AC120Volts/60Hz/30W Output power AC 12Volts/ 1.25A...
Page 362 Prestige 650 Series User’s Guide AC Power Adapter model AA-121A3D Input power AC230Volts/50Hz/140mA Output power AC12Volts/1.3A Power consumption 15 W Safety standards ITS-GS, CE (EN 60950) Power Adaptor Specifications...
Page 363: Appendix I Index
Prestige 650 Series User’s Guide Appendix I Index Call Filters Built-In ............23-1 User-Defined ..........23-1 Address Assignment ........4-2 Call Scheduling..........31-1 Ad-hoc Configuration ........C-2 Maximum Number of Schedule Sets..31-1 ADSL, what is it?........... xxiii PPPoE............31-3 Alternative Subnet Mask Notation....
Page 364 Prestige 650 Series User’s Guide DNS ............... 16-3 Generic Filter Rule........23-14 Domain Name........... 4-2, 7-6 Remote Node..........19-9 Domain Name System ........4-1 Remote Node Filter ........19-9 DS ........See Distribution System Remote Node Filters ........23-20 DSL (Digital Subscriber Line)....... xxiii Sample............23-18 DSL, What Is It? ..........
Page 365 Prestige 650 Series User’s Guide Hop Count..........19-8, 20-3 IP Pool Setup ..........3-13 Host..............2-3 IP Protocol ............. 30-4 Host IDs ............B-1 IP Routing Policy (IPPR)....... 30-1 HTTP ............... 7-6 Benefits............30-1 HyperTerminal program ....... 27-6, 27-9 Cost Savings ..........30-1 Criteria............
Page 366 Prestige 650 Series User’s Guide Multiprotocol Encapsulation......3-2 PPTP..............7-6 My WAN Address ......... 19-7 Precedence..........30-1, 30-4 Priority............12-14 Priority-based Scheduler ........12-4 Private........... 19-8, 20-4 Nailed-Up Connection ........3-6 Proportional Bandwidth Allocation....12-2 NAT........3-4, 7-5, 7-7, 23-16 Protocol ............23-10 Application ..........7-3 Protocol Filter Rules........23-16 Applying NAT in the SMT Menus....
Page 367 Prestige 650 Series User’s Guide Direction ............4-3 Syslog Server ..........26-6 Version............4-3 System Routing Policy ..........30-1 Console Port Speed ........26-5 RTS Threshold ........5-2, 17-2 Diagnostic..........26-8 Log and Trace..........26-5 Syslog and Accounting......26-6 System Information ........26-4 Sample IP Addresses........
Page 368 UPnP......See Universal Plug and Play User Name ............8-2 User Profiles ......... 5-13, 25-5 ZyNOS ..........27-1, 27-2 Using LEDs To Diagnose Problems ....A-1 ZyNOS F/W Version........27-1 ZyXEL Limited Warranty Note..............iv VC-based Multiplexing ......... 19-2 VPI & VCI............3-2 VPN ..............6-1 Index...

ZyXEL Communications PRESTIGE 650H User Manual

Chapter 1 Getting to Know Your Prestige

Chapter 2 Introducing the Web Configurator

Chapter 3 Wizard Setup

Chapter 4 LAN Setup

Chapter 5 Wireless LAN Setup

Chapter 6 WAN Setup

Chapter 7 Network Address Translation (NAT)

Chapter 8 Dynamic DNS Setup

Chapter 9 Time and Date Setup

Chapter 10 Remote Management Configuration

Chapter 11 Universal Plug-And-Play (Upnp)

Chapter 12 Bandwidth Management

Chapter 13 Maintenance

Chapter 14 Introducing the SMT

Chapter 15 General Setup

Chapter 16 LAN Setup

Chapter 17 Wireless LAN Setup

Chapter 18 Internet Access

Chapter 19 Remote Node Configuration

Quick Links

Troubleshooting

Related Manuals for ZyXEL Communications PRESTIGE 650H

Summary of Contents for ZyXEL Communications PRESTIGE 650H