Tuner; Usb (Sr6004 Only) - Marantz SR5004 User Manual

Symptom Cause
No sound is heard
from the monitor HDMI audio enable mode is
TV connected to established.
the HDMI terminal.
Image and audio
are unstable
over an HDMI
connection. The connection uses a long cable.
(There is noise,
the stream is
interrupted, etc.)

TUNER

Symptom Cause
Cannot receive The antennas have not been
AM or FM signals. connected properly.
A noise is
generated when The unit is receiving interference
receiving an AM from other components.
signal.
A noise is
generated when The signal from the broadcasting
receiving an FM station is weak.
signal.

USB (SR6004 ONLY)

Symptom Cause
Even when the
USB storage
device is
• The unit cannot recognize the
connected, "NO
USB storage device because of
DEVICE" remains
connection trouble or some other
on the status
issue.
display, and the
device is not
recognized.
• A device that cannot be
recognized by the unit has been
"CHECK DEVICE"
connected.
appears on the
status display
when the USB
storage device is
connected.
• The device has been connected
through a USB hub.
Solution Page
No sound is heard from the
monitor TV in Enable mode. Select 36
Through.
Use a short cable.
Use of a cable no longer than 5 –
meters is recommended.
Use a Category 2 (high-speed
–
supported) cable.
Solution Page
Make sure the AM and FM
antennas are properly connected to
15
the AM and FM antenna terminals,
respectively.
Change the location of the AM
–
antenna.
Install an outdoor FM antenna. 15
Solution Page
• Check whether the USB storage –
device and USB cable are fi rmly
plugged into the unit's USB
connector.
–
• Try removing the USB storage
device from the unit, and re-
connecting it.
• Try turning the unit's power off –
and back on, and re-connecting
the device.
• Even when a USB storage device –
complies with the USB Mass
Storage Class standard, it may
not be possible to play its fi les
using the unit. (This does not
mean that something is wrong
with the unit itself.)
–
• USB storage devices cannot be
connected through a USB hub.
Symptom Cause
• A format other than FAT16
"CHECK FS"
or FAT32 is used as the USB
appears on the
storage device's format.
status display
• A USB storage device that has
when a USB
been formatted using a fi le
storage device is
system not supported by the unit
connected.
is being used.
"!OVER
CURRENT!"
appears on the The overcurrent protection function
status display of the unit's USB connector has
when a USB been triggered.
storage device is
connected.
"NO AUDIO FILE"
appears on the
No playable fi les have been
status display when
recorded on a USB storage device.
a USB storage
device is connected.
"CHECK FILE" • An attempt has been made to
appears on the play a copyright-protected fi le.
status display
• The fi le is damaged.
when a USB
Alternatively, its extension and
storage device is
fi le structure are incompatible.
connected.
• The USB storage device is
partitioned into a number of
The fi les recorded
partitions.
on the USB
storage device are
• The number of folders exceeds
not displayed.
700 or the number of fi les
exceeds 65535.
"PRESS TOP KEY"
appears on the status The fi le cannot be read properly.
display.
"PRE O E
An iPod not supported by the unit's
KEY" ppe r
direct mode has been connected.
the t tu i pl y
"CHECK iPod"
The iPod could not be detected
appears on the
properly.
status display.
ENGLISH
TROUBLESHOOTING
Solution Page
• Set the format to FAT16 or –
FAT32, and record the fi les.
–
• Use a USB storage device that
has been formatted using a fi le
system supported by the unit.
No guarantees are made for the
operation of a hard disk drive that
is powered from the unit's USB
connector. –
Remove the connected USB
storage device, and turn the unit's
power off and back on.
Record the supported fi le on a USB
64
storage device.
• The unit cannot play copyright- –
protected fi les.
–
• Check the fi le.
• If the device is partitioned into –
a number of partitions, displays
only for the fi rst partition will
appear.
• No displays appear for folders –
after folder no.700 or for fi les
after fi le no.65535.
Press the TOP button, and try
–
rereading the fi le.
Press the SETUP/MODE button,
8
and use the iPod in remote mode.
Turn off the unit's power and turn it
back on. If the iPod still cannot be
detected, reset the iPod. For details 16
on how to reset the iPod, refer to
the iPod's operating instructions.
81