Marantz SR5004 User Manual page 79

LEARN MODE
This remote controller is capable of learning and
storing codes used by other remote controls that
you already own.
For codes which are not learned, the remote
controller will transmit either the Marantz preset
codes from the initial settings, or remote codes
from another manufacturer's AV equipment which
is set by the customer.
The receiver sensor for the remote controller signals
is located at the top of the remote controller.
Notes
• This remote controller is capable to learn around
160 codes.
• When the batteries are getting weak , the learning
procedure is not successful.
LEARNING PROCEDURE
1.
Place the remote controller so that its
infrared signal transmitter is facing the
infrared signal receiver on the Marantz
remote controller at a distance of about 5
cm (2 inches).
2.
Press and hold down the SET and SETUP
buttons until LEARN indicator blinks.
3.
Select the SOURCE button to select the
SOURCE.
4.
Select the button to be learned.
• LEARN indicator lights up.
Notes
• The learning function is unavailable for all
SOURCE buttons and HDMI button in any
mode.
• The learning function is unavailable for all
buttons in TUNER mode and AMP mode.
5.
Press and hold the button of the original
remote controller to learn until the SEND
indicator blinks twice.
Notes
• When the SEND indicator blinks once, repeat this
step.
• If the LEARN indicator fl ashes when the SEND
indicator is lit, then the button cannot be
learned.
• When the memory of the remote controller is full,
the LEARN and SEND indicators blink once. If
you want to learn the code, you should erase other
learned button.
6.
Repeat steps 4 and 5 to learn other buttons
in same SOURCE.
7.
3 6
Repeat steps to to learn other
SOURCE.
8.
When you have fi nished programming the
remote controller, press the SET button,
then LEARN indicator stops blinking and
exits from the LEARN mode.
Notes
• When the SEND indicator blinks once again,
the transmitting code is unavailable for remote
controller, or the transmitting signal is intercepted
by noise.
• If no buttons are pressed for approximately 1
minutes while in the LEARN mode, the remote
controller automatically exits from the LEARN
mode.
ERASING PROGRAMMED CODES
(RETURNING TO INITIAL SETTINGS)
Codes can be erased in three ways: by buttons,
sources, and by all memory contents.
Erasing the code by buttons
1.
Press and hold down the SET and SETUP
buttons until LEARN indicator blinks.
2.
Select the SOURCE button to select the
button to be erased.
3.
Press and hold down the HDMI button
and press the learned button twice to be
erased.
• SEND indicator blinks twice and the
mode returns to LEARN mode.
4.
To return the NORMAL mode, press the
SET button.
Erasing the code by SOURCE
1.
Press and hold down the SET and SETUP
buttons until LEARN indicator blinks.
2.
Press and hold down the HDMI button and
press the learned SOURCE button twice to
be erased.
• LEARN indicator lights.
ENGLISH
ADVANCED OPERATION
3.
Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press ENTER button and simply touch
any other button.
4.
To return the NORMAL mode, press the
SET button.
ERASING THE ALL SOURCES
1.
Press and hold down the SET and SETUP
buttons until LEARN indicator blinks.
2.
Press and hold down the HDMI button and
press POWER ON and POWER OFF button.
• LEARN indicator lights.
3.
Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press ENTER button and simply touch
any other button.
4.
To return the NORMAL mode, press the SET
button.
Note
Erasing codes will return to the factory preset code,
or there will leave empty if the button has no factory
preset code.
77