Marantz SR5004 User Manual page 31

8.
Repeat step 7 until measuring up to 6 points
measuring the main listening position
and other positions where people will
commonly listen.
When all measurements end, the following
GUI appears on the display.
Audyssey MultEQ Setup
Speaker Check : OK
Calculate
: : Enter : OK Exit : Exit
Select "Calculate" with the 3/4 cursor
buttons and press the ENTER button to
calculate measurement results. During
calculations, the following GUI appears on
the display.
Audyssey MultEQ Setup
--------------
Now Calculating!
: : Enter : Exit :
Notes
• Fewer than 6 positions may be measured, but it
is recommended to measure in all 6 positions for
best results. Measuring in fewer than 3 position
is not recommended as it does not provide enough
acoustical information for good correction.
• The time needed to complete calculations
depends on the number of connected speakers and
measured listening positions. The more speakers
and listening positions, the more time is needed.
9.
Checking Measurement Results
When calculations for the measurement
results end, a screen appears for confi rming
the calculation results.
Check Result
Speakers Configuration
Speakers Size
Speakers Distance
Channel Level
Crossover Frequency
Store
: Up / Down : Enter : Select Exit : Exit
Select items to check with the 3/4 cursor
buttons and press the ENTER button to
enter them.
Note
To check equalizer (MultEQ ® ) parameters, see
page 38.
[Example]
Confi rmation screen for speaker detection
Speakers Configuration
Check Speaker Results
Front Left
: Yes
Front Height Left
: No
Center : No
Front Height Right : No
Front Right
: Yes
Surround Right
: Yes
Surround Back : No
Surround Left : Yes
Subwoofer
: Yes
Return
: : Enter : Return Exit : Exit
[Example]
Confi rmation screen for speaker size.
Speakers Size
Front Left
: Auto
Front Height Left
: Auto
Center : Auto
Front Height Right : Auto
Front Right : Auto
Surround Right
: Auto
Surround Back Right : Auto
Surround Back Left : Auto
Surround Left : Auto
Return
: : Enter : Return Exit : Exit
[Example]
Confi rmation screen for the distance from speakers
to the listening position
Speakers Distance
Unit : Meters
Front Left : 30.0 ft
Front Height Left : 30.0 ft
Center
: 19.3 ft
Front Height Right : 29.6 ft
Front Right : 29.6 ft
Surround Right : 21.5 ft
Surround Back Right
: 12.3 ft
Surround Back Left
: 11.6 ft
Surround Left : 16.3 ft
Subwoofer : 12.5 ft
Return
: Up / Down : Enter : Return Exit : Exit
* The units can be changed by moving the cursor
to Meters of Unit and pressing 1 / 2 the cursor
buttons. Each time a 1 / 2 cursor button is pressed,
the units alternate between Feet and Meters.
Note
This system cannot measure a distance of 9.15 m
(30.0 ft) or higher. In this case, >9.15 m (>30.0 ft)
is displayed.
[Example]
Confi rmation screen for channel level.
Channel Level
Front Left : 0.0dB
Front Height Left : 0.0dB
Center : -6.5dB
Front Height Right : 0.0dB
Front Right : -1.5dB
Surround Right : +1.0dB
Surround Back Right : +9.5dB
Surround Back Left : +12.0dB
Surround Left : -2.5dB
Subwoofer : -12.5dB
Return
: : Enter : Return Exit : Exit
[Example]
Confi rmation screen for crossover frequency.
Crossover Frequency
Front : Auto
Front Height : Auto
Center : Auto
Surround : Auto
Surround Back : Auto
Return
: : Enter : Return Exit : Exit
ENGLISH
SETUP
* Auto is displayed to indicate that the speaker
size and crossover frequency results were
automatically measured.
10.
Storing Measurement Results in Memory
Once fi nished confi rming the measurement
results, select "Return" with the 3/4 cursor
buttons and press the ENTER button to
display the Check Result screen.
Check Result
Speakers Configuration
Speakers Size
Speakers Distance
Channel Level
Crossover Frequency
Store
: Up / Down : Enter : OK Exit : Exit
Place the cursor on "Store" and press
the ENTER button to store all parameters
including the equalizer parameters in memory.
If not wanting to store the calculation results
in memory, press the Exit button.
Note
Pressing "Exit" prior to pressing "Store" erases
all measurement results and calculation results,
therefore operate the remote controller with care.
When storing operations end, the following GUI
appears on the display.
Speaker Setup
Auto Setup
Manual Setup
Return
: Up / Down : Enter : Select Exit : Exit
Note
• Do not turn the power to the unit off while storing
parameters in memory. This may erase or corrupt
data in the unitʼs memory and may damage the unit.
29