Important
! Do not move the receiver with the Bluetooth
ADAPTER connected. Doing so could cause
damage or faulty contact.
% Switch the receiver into standby
and connect Bluetooth ADAPTER to the
ADAPTER PORT.
! For instructions on playing the Bluetooth
wireless technology device, see Pairing the
Bluetooth ADAPTER and Bluetooth wireless
technology device on page 35 .
Connecting an iPod
This receiver has a dedicated iPod terminal
that will allow you to control playback of audio
content from your iPod using the controls of
this receiver.
iPod iPhone iPad
AUTO SURR/ALC/
ADVANCED
STANDARD
DIRECT CONTROL
STREAM DIRECT
SURROUND
SURROUND
HOME THX
USB
HDMI 3 INPUT
5V
2.1 A
iPod iPhone iPad
iPod
iPod cable
(supplied)
MENU
% Switch the receiver into standby then
use the supplied iPod cable to connect
your iPod to the iPod iPhone iPad USB
terminal on the front panel of this
receiver.
! It is also possible to connect using the cable
included with the iPod, but in this case it is not
possible to view pictures via the receiver.
! For the cable connection, also refer to the
operating instructions for your iPod.
! For instructions on playing the iPod, see
Playing an iPod on page 30 .
Connecting a USB device
It is possible to play audio and photo files by
connecting USB devices to this receiver. It
is also possible to connect a USB keyboard
(US-international layout) to the receiver to enter
text in the following GUI screens.
! Change the input name in the Input Setup
menu (page 28).
! Add names to radio station presets (page 33).
iPod iPhone iPad
AUTO SURR/ALC/
ADVANCED
STANDARD
DIRECT CONTROL
STREAM DIRECT
SURROUND
SURROUND
USB
HDMI 3 INPUT
5V
2.1 A
iPod iPhone iPad
USB mass
storage device
USB keyboard
% Switch the receiver into standby
then connect your USB device to the
USB terminal on the front panel of this
receiver.
! This receiver does not support a USB hub.
! For instructions on playing the USB device,
see Playing a USB device on page 31 .
Connecting an HDMI-equipped
component to the front panel
input
iPod iPhone iPad
AUTO SURR/ALC/
ADVANCED
STANDARD
DIRECT CONTROL
STREAM DIRECT
SURROUND
SURROUND
HOME THX
USB
HDMI 3 INPUT
5V
2.1 A
iPod iPhone iPad
Video camera (etc.)
Connecting to a wireless LAN
Wireless connection to the network is possible
through a wireless LAN connection. Use the
separately sold AS-WL300 for connection.
! For instructions on setting the wireless LAN
converter, see Network Setup menu on page
71 .
Connecting your equipment
ADAPTER PORT
DC OUTPUT
(OUTPUT 5 V
LAN
2
for WIRELESS LAN
(OUTPUT
0.1 A MAX)
(10/100)
5 V
0.6 A MAX)
L
OPTICAL
BLE
ASSIGNABLE
IN
2
IN
1
IN
2
IN
3
OUT
(
CD
)
(
TV/SAT
)
(
DVR/BDR
)
(
VIDEO
)
Internet
OOFER 2
SURROUND SURR BACK FH / FW
PRE OUT
(Single)
L
Modem
R
SURROUND BACK
FRONT HEIGHT / FRONT WIDE /
B
L
R
L
(Single)
R
L
Router
WAN
DC 5V
Ethernet
WPS
Wireless LAN converter (AS-WL300)
Connecting an IR receiver
If you keep your stereo components in a closed
cabinet or shelving unit, or you wish to use the
sub zone remote control in another zone, you
can use an optional IR receiver (such as a Niles
or Xantech unit) to control your system instead
of the remote sensor on the front panel of this
receiver.
! Remote operation may not be possible if direct
light from a strong fluorescent lamp is shining
on the IR receiver remote sensor window.
! Note that other manufacturers may not use
the IR terminology. Refer to the manual that
came with your component to check for IR
compatibility.
! If using two remote controls (at the same
time), the IR receiver's remote sensor takes
priority over the remote sensor on the front
panel.
03
23
En