Omron H5F Datasheet page 15

1. Change the setting of the output ON/OFF switch from AUTO to
OFF.
2. Return the setting of the output ON/OFF switch from
OFF to AUTO while holding down the
The OFF state will be held from the point at which this
operation is performed (indicated by the arrow) until
the next (regular) ON time.
Note: 1. This operation is possible in run mode only.
2. Override and automatic return operation can be cleared by
setting the output ON/OFF switch to the opposite of the
present status. For example, if the output is ON, override
and automatic return operation can be cleared by setting
the output ON/OFF switch to OFF.
3. Override and automatic return operation cannot be set or
cleared if power is not being supplied to the Time Switch.
4. Override and automatic return operation is cleared if any of
the settings are changed.
Using Override and Automatic Return Operation for
Pulse-output Operation
Override and automatic return operation proceeds in the following
way when used for pulse-output operation.
• If override and automatic return operation starts with a forced ON,
output is turned ON for the time corresponding to the set pulse
width.
• If override and automatic return operation starts from a forced OFF,
output remains OFF until the pulse output ends.
The operation method is the same as for timer operation.
Example 1: Override and automatic return operation
starting with a forced ON while output is ON
(pulse width: 30 min)
Regular
program
Output
30 min
Point at which the Output ON/OFF Key changes from
AUTO to ON.
Point at which the Output ON/OFF Key changes from
ON to AUTO with the
Example 2: Override and automatic return operation
starting with a forced ON while output is OFF
(pulse width: 30 min)
Regular
program
Output
30 min
Point at which the Output ON/OFF Key changes from
AUTO to ON.
Point at which the Output ON/OFF Key changes from
ON to AUTO with the
Key.
WRITE
From the next
time onwards,
output operates
according to the
regular program.
Key held down.
WRITE
From the next time
onwards, output
operates
according to the
regular program.
Key held down.
WRITE
Example 3: Override and automatic return operation
Switch
ON
Regular
AUTO
program
OFF
Output
Point at which the Output ON/OFF Key changes from
AUTO to OFF.
Point at which the Output ON/OFF Key changes from
OFF to AUTO with the
Program Check Function
The days and times at which output turns ON or OFF over the course
of one week can be displayed continuously in the actual order in
which they will occur.
1. Press the
run mode to start the program
check.
The display will flash test and the
day and time of the next change in
output status will be displayed.
2. Press the
The display will change to the day
and time of the next change in out-
put status. (Continue pressing the
Key to display the days and
WRITE
times for one week.)
3. If the
WRITE
the last setting for the week dis-
played, end is displayed for 2 s and
then the Time Switch automatically
returns to run mode.
Note: 1. The program check can be started from run mode only.
2. Press the
reaching the end of the program check function display se-
quence.
3. The ON and OFF symbols (
program check have no effect on the present operation.
4. Only ON times are displayed for pulse-output operation.
starting from a forced OFF while output is ON
(pulse width: 30 min)
Key held down.
WRITE
Key for 2 s min. in
TEST
The color
Key.
WRITE
Key is pressed with
Key again to return to run mode before
TEST
Digital Daily Time Switch
From the next
time onwards,
output operates
according to the
regular program.
indicates flashing items.
SU MO TU WE TH FR SA
1 15
PM
te st
PW
In the above example, output will
turn ON at 1:15 pm on Monday.
SU MO TU WE TH FR SA
5 30
PM
te st
PW
In the above example, output will
turn OFF at 5:30 pm on Monday.
SU MO TU WE TH FR SA
e nd
PW
/ ) displayed during
H5F
15