Yamaha MOTIF RACK ES Owner's Manual page 90

Utility
CtrlReset Controller Reset
LCD Cntrst LCD Contrast
PlgAutoLoad Plug-in Auto Load
BulkIntrval Bulk Interval
Output
L&R Gain L Gain and R Gain
Asn1/2Gain Assignable 1/2 Gain
Asn3/4Gain Assignable 3/4 Gain
MEQ (Master Equalizer)
MEF (Master Effect)
Voice
ArpOutSw
Arpeggio Output Switch
ArpTransCh Arpeggio Transmit Channel
AS1/2 Assign Assign 1/2
BC Assign Breath Controller
RB Assign Ribbon Controller
FC1/2 Assign Foot Controller
CtrlAsn (Control Assign)
ArpSwitch Arpeggio Switch
ArpHold Arpeggio Hold
ASA/B Asgn Assign A/B
ASA/B Dest Assign A/B Destination
FS Asgn Foot Switch Assign
ArpAsgn Arpeggio Assign
ArpAsgnMode Arpeggio Assign Mode
90
Owner's Manual
Determines the status of the external controllers when switching between Voices. When this is set to "off,"
the controllers are kept at the current setting. When this is set to "on," the controllers are reset to the default
states (below).
Settings: reset, hold
If you select "reset," the controllers will be reset to the following states/positions:
Pitch Bend: Center Foot Switch: Off
Modulation Wheel: Minimum Expression: Maximum
Aftertouch: Minimum Foot Volume: Maximum
Foot Controller: Maximum Sustain: Off
Breath Controller: Maximum
Sets the LCD display for optimum legibility.
Settings: 1~16
Determines whether the Board Voice data is automatically loaded (on) or not (off) when turning the power on
(Plug-in Load function in the JobSel display).
Settings: On, Off
Determines the transmit interval of the Bulk Dump.
Settings: 1~5
The higher the value, the larger the transmit interval.
Sets the signal gain of each output jack.
Settings: 0dB, +6dB
These special voice-related settings are available only when entering the Utility from the Voice mode, From
this display you can apply five-band equalization (LOW, LOW MID, MID, HIGH MID, HIGH) to all Voices.
Parameters are the same as in the MEQ display in the Performance/Multi Common Edit mode (page 79).
n For details about Equalizer, see page 60.
These special voice-related settings are available only when entering the Utility from the Voice mode. From
this display you can set the Master Effect related parameters applied to all the Voices. Parameters are the
same as in the MEF display in the Performance/Multi Common Edit mode (page 80).
These special voice-related settings are available only when entering the Utility from the Voice mode. From
this display you can make settings that apply commonly to all Voices.
This enables or disables MIDI data output for the Arpeggio function. When this is set to "on," Arpeggio data
is sent via MIDI in the Voice mode. In the Performance/Multi mode, you can set in the "OutputSw" parameter
from the Arpeggio Edit.
Settings: on, off
Determines the MIDI channel through which Arpeggio playback data will be sent (when Output Switch
above is on). In the Performance/Multi mode, you can set this in the "TransmitCh" parameter in the Arpeggio
Edit mode (page 89).
Settings: 1~16
Sets the parameters related to the controllers in the Voice mode. Parameters are the same as in the CtrlAsn
display in the Performance/Multi Common Edit mode (page 80).
Determines the Control Numbers corresponding to the external controllers. For details, see page 46.
Determines the Control Number that controls on/off for Arpeggio playback.
Settings: off, 1~95
Determines the Control Number that controls on/off for the "Hold" parameter (page 88).
Determines the Control Numbers corresponding to Assign A and Assign B, and sets the Destinations
(functions) assigned to the Control Numbers.
Settings: Refer to the separate Data List booklet.
Determines the Control Number corresponding to the Footswitch.
Settings: Refer to the separate Data List booklet.
Determines the Control Number for switching among Arpeggios 1-5, stored to each Voice/Performance/
Multi. For details, see page 44.
Determines the mode for switching among Arpeggios 1-5, stored to each Voice/Performance/Multi.
Settings: inc, direct
inc.................... Each time the MOTIF-RACK ES receives a message via the selected Control Change number, Arpeggios 1-5
can be switched. The actual Control Change data value does not matter.
direct ............... You can select the Arpeggio corresponding to the value of the selected Control Change number: 0~25
(Arpeggio 1), 26~50 (Arpeggio 2), 51~76 (Arpeggio 3), 77~101 (Arpeggio 4), 102~127 (Arpeggio 5)