Yamaha MOTIF RACK ES Owner's Manual page 72

Voice mode Voice Edit (for Normal Voice)
LFO (Low Frequency Oscillator)
Wave LFO Wave
Speed LFO Speed
KeyOnSync LFO Key On Sync
(KOnSyn)
KeyOnDelay LFO Key On Delay Time
(KOnDly)
Pmod LFO Pitch Modulation Depth
Fmod LFO Filter Modulation Depth
Amod LFO Amplitude Modulation
Depth
FadeIn LFO Fade In Time
PhaseOffset (Offset) LFO Phase Offset
Dest1-3Ratio LFO Destination Ratio
(D1-3Rtio)
EQ (Equalizer)
Type EQ Type
72
Owner's Manual
This display gives you a comprehensive set of controls over the LFO for each individual Element. The LFO
can be used to create vibrato, wah, tremolo and other special effects, by applying it to the pitch, filter and
amplitude parameters.
Determines the LFO waveform used to vary the sound.
Settings: saw, tri, squ
saw (sawtooth wave)
Set the speed of the LFO waveform. A larger setting means a faster speed.
Settings: 0 ~ 63
When this is set to on, the LFO waveform is reset every time a note is played.
Settings: off, on
Off
Note On
Determines the delay time between the moment a Note On message is received to the moment the LFO
comes into effect. A higher value results in a longer delay time.
Settings: 0 ~ 127
Determines the amount (depth) by which the LFO waveform varies (modulates) the pitch of the sound. The
higher the setting, the greater the depth of control.
Settings: 0 ~ 127
Determines the amount (depth) by which the LFO waveform varies (modulates) the Filter Cutoff frequency.
The larger the setting, the greater the depth of control.
Settings: 0 ~ 127
Determines the amount (depth) by which the LFO waveform varies (modulates) the amplitude or volume of
the sound. The larger the setting, the greater the depth of control.
Settings: 0 ~ 127
Determines the amount of time for the LFO effect to fade in (after the "KeyOnDelay" time has elapsed).
A higher value means a slower fade-in.
Settings: 0 ~ 127
Determines the offset values of the "Phase" parameter (in the [VOICE]
the respective Elements.
Settings: +0, +90, +120, +180, +240, +270
Determines the LFO Wave Depth.
Settings: 0 ~ 127
Determines the Equalizer Type. This synthesizer features a wide selection of various Equalizer Types, which
can be used not only to enhance the original sound, but even completely change the character of the
sound. The particular parameters and settings available depend on the specific Equalizer Type that is
selected.
Settings: EQ L/H (L/H), P.EQ, Boost6 (B6), Boost12 (B12), Boost18 (B18), thru
EQ L/H (Low/High) ................ This is a "shelving" equalizer, which combines separate high and low frequency bands.
P.EQ (Parametric EQ) ............ The Parametric EQ is used to attenuate or boost signal levels (gain) around the Frequency. This
type features 32 different "Q" settings, which determine the frequency band width of the
equalizer.
Boost6 (Boost 6dB)/Boost12 (Boost 12dB)/Boost18 (Boost 18dB)
.............................................. These can be used to boost the level of the entire signal by 6dB, 12dB and 18dB, respectively.
thru ........................................ If you select this, the equalizers are bypassed and the entire signal is unaffected.
n The available parameters differ depending on which Filter type is selected here.
When set to EQ L/H
Low Freq
Settings: 20.1Hz – 2.00kHz
Gain
High Freq
Settings: 503.8Hz – 10.1kHz
+
0
–
Low Gain
Settings: -32 – 0 – +32
tri (triangle wave)
On
Time
Note On
Common Edit
When set to P.EQ
+
0
Frequency
–
Freq
High Gain
Settings: 139.7Hz – 12.9kHz
Settings: -32 – 0 – +32
squ (square wave)
Time
LFO display) for
Q (Frequency characteristic)
Settings: 0 – 31
Frequency
Gain
Settings: -32 – 0 – +32