Yamaha MOTIF RACK ES Owner's Manual page 74

Voice mode Voice Edit (for Drum Voice)
RcvNoteOff Receive Note Off
AltnateGrp Alternate Group
Pitch
CoarseTune Coarse
FineTune Fine
PitchVelSns Pitch Velocity Sensitivity
Filter
Cutoff LPF Cutoff
Resonance LPF Resonance
CutofVelSns LPF Cutoff Velocity Sensitivity
HPF Cutoff HPF Cutoff
AMP (Amplitude)
Level Level
Pan Pan
AltnatePan Alternate Pan
RandomPan Random Pan
AttackTime AMP Attack Time
Decay1Time AMP Decay1 Time
Decay1Lvl AMP Decay1 Level
Decay2Time
AMP Decay2 Time
LvVelSns Level Velocity Sensitivity
EQ (Equalizer)
74
Owner's Manual
Selects whether MIDI Note Off messages are received by each Drum Key.
Settings: off, on
n This parameter is only available if the "WaveType" parameter in the OSC display is set to "PresetWave."
Sets the Alternate Group to which the Wave is assigned. In a real drum kit, some drum sounds cannot
physically be played simultaneously, such as open and closed hi-hats. You can prevent Waves from playing
back simultaneously by assigning them to the same Alternate Group. Up to 127 Alternate Groups can be
defined. You can also select "off" here if you wish to allow the simultaneous playback of sounds.
Settings: off, 1 ~ 127
n This parameter is only available if the "WaveType" parameter in the OSC display is set to "PresetWave."
Determines the pitch of each Drum Key Wave (or Normal Voice) in semitones.
Settings: -48 ~ +48
n For a Normal Voice, this parameter adjusts the position of its note (not its pitch) relative to note C3.
Determines the fine tuning for the pitch of each Drum Key Wave (or Normal Voice).
Settings: -64 ~ +63
From this display you can determine how the pitch of the Drum key responds to velocity. For positive values,
the more strongly you play the note, the higher the pitch becomes. For negative values, the more strongly
you play the note, the lower the pitch.
Settings: -64 ~ +63
n This parameter is only available if the "WaveType" parameter in the OSC display is set to "PresetWave."
You can apply filter settings to the Drum Voice. The MOTIF-RACK ES lets you apply a low pass filter and
high pass filter to each individual Drum key.
n This parameter is only available if the "WaveType" parameter in the OSC display is set to "PresetWave."
Sets the Cutoff Frequency of the Low Pass Filter.
Settings: 0 ~ 255
Determines the amount of Resonance (harmonic emphasis) applied to the signal at the Cutoff Frequency.
Settings: 0 ~ 127
Determines the velocity sensitivity of the Low Pass Filter Cutoff Frequency. Positive settings will cause the
Cutoff Frequency to rise the harder you play the note. A negative setting will have the opposite effect.
Settings: -64 ~ 0 ~ +63
Determines the Cutoff Frequency of the High Pass Filter.
Settings: 0 ~ 255
n The "AltnatePan," "RandomPan," "AttackTime," "Decay1Time," "Decay1Lvl," "Decay2Time," and "LvVelSns"
parameters are only available if the "WaveType" parameter in the OSC display is set to "PresetWave."
Sets the output level of each Key. This lets you make detailed balance adjustments among the various
sounds of the Drum Voice.
Settings: 0 ~ 127
Sets the Pan position for each sound in a Drum Voice (Drum Kit). This will also be used as the basic Pan
position for the Alternate and Random settings.
Settings: L63 (far left) ~ C (center) ~ R63 (far right)
Sets the amount by which the sound is panned alternately left and right for each received Note On
message. The Pan setting is used as the basic Pan position.
Settings: L64 ~ 0 ~ R63
Determines the amount by which the sound of the selected Drum key is panned randomly left and right for
each received Note On message. The Pan setting (above) is used as the Center Pan position.
Settings: 0 ~ 127
Settings: 0 ~ 127
Settings: 0 ~ 127
Settings: 0 ~ 127
Settings: 0 ~ 126, hold
Decay 2 Time = 0 ~ 126
Attack level
Level
Decay 1 level
Decay 2
Attack Decay 1
time
time
time
Note On
Determines the velocity sensitivity of the Amplitude Envelope Generator's output level. For positive settings,
the more strongly you play the note, the more the volume changes. A negative setting will have the opposite
effect.
Settings: -64 ~ 0 ~ +63
Same as in Normal Element Edit. See page 72.
n This parameter is only available if the "WaveType" parameter in the OSC display is set to "PresetWave."
Decay 2 Time = hold
Attack level
Level
Decay1 level
Time
Attack
Decay 1
time
time
Note On
Time
Decay 2
time