Table of Contents
Advertisement
Initial installation
Setting options for DVB-C reception:
If you have not selected a DVB-C antenna in the antenna
selection: Continue with Setting options for DVB-S recep-
tion (see right hand column).
The normal DVB-C settings are derived from the selection
of the location and do not need to be changed.
Settings
INITIAL INSTALLATION (DVB-C)
Scrambled stations
Search method
Start frequency
Network ID
Symbol rate 1
Symbol rate 2
QAM modulation 1
QAM modulation 2
Proceed
OK
Select and adapt settings for DVB-C reception.
Encrypted
You can state whether coded stations are to be searched
stations
for in the search/update.
scrambled stations.
received in connection with a CA module and the appro-
priate Smart Card. Handling of the CA module is described
on page 55.
If a CA module with a SmartCard is already plugged in for
the station search, all the stations which this module can
descramble are also saved when no is preset.
Search
If you want to run the station search independently of
method
the channel grid, select frequency search for the search
method.
Start
The DVB stations are only searched for in the frequency
frequency
range above the start frequency.
Network ID
Only change these defaults if you are familiar with other
symbol rates and types of modulation or if you have to
Symbol rate
specify the network ID for your cable network. In the
case of small cable networks fed directly from the satel-
QAM
lite, the rate of 6900 might have to be replaced by 6111.
modulation
Your cable provider has the information you need.
OK Proceed.
- 24
no
yes
Channel search
047.0 MHz
none
6875
6900
64
256
Select
yes
to save all found
However, these stations can only be
Setting options for DVB-S reception:
If you have not selected a DVB-S antenna in the antenna
selection: Continue with Setting options for all types of
reception on page 28.
The normal DVB-S settings are derived from the selection
of the location and do not need to be changed in most
cases.
Select
INITIAL INSTALLATION (DVB-S)
satellite
Select satellite installation
Single satellite
installation
2 satellites on 22 kHz switchbox
2 satellites on toneburst switch
Max. 4 satellites on DiSEqC multiswitch
DiSEqC one cable communal system
other communal installation
Proceed
OK
Selecting the satellite system.
Specify how you receive which satellite(s) (single
satellite or type of satellite system). Ask your dealer
if required.
Single
Reception of a single satellite via a connected LNC (LNB).
satellite
See page 25 for settings.
2 satellites
Reception of two different satellites with two LNCs (LNBs)
on 22 kHz
which are connected to the TV set by a 22 kHz switchbox.
switchbox
See page 25 for settings.
2 satellites
Reception of two different satellites with two LNCs (LNBs)
on toneburst
which are connected to the TV set by a toneburst switch.
switch
See page 25 for settings.
Max. 4
The TV set controls a DiSEqC multiswitch to which up to
four LNCs (LNBs) for different satellites are connected.
satellites
on DiSEqC
See page 26 for settings.
multiswitch
Select setting if the TV set is connected to a DiSEqC single-
DiSEqC
one cable
cable system (according to EN 50494). Several Sat receiv-
ers can be connected to one Sat cable. See page 26 for
communal
system
settings.
other
Select setting if the TV set is connected to a single-cable
system (without DiSEqC). Several Sat receivers can be
communal
installation
connected to one Sat cable. Unlike a DiSEqC single-cable
system there are restrictions in the range of certain recep-
tion frequencies in single-cable community systems. See
page 27 for settings.
OK Proceed
(to the appropriate page of the satellite system).
OK
Back
Advertisement
Table of Contents
