U-Line UCBF632-SS12A User Manual & Service Manual page 53

USER GUIDE
Parameter
P51 condenser fan activity in the absence of
the condenser probe (P61 = 0)
0 = in parallel with compressor
1 = on
P52 the temperature below which the
condenser fan is switched off in the
presence of the condenser probe (P61 =
1) and on condition that the compressor
is on (with reference to the condenser
probe); see also P54
P53 P52 differential
P54 condenser fan switch off delay on
switching off the compressor in the
presence of the condenser probe (P61 =
1); see also P52
P55 chill and freeze cycle completion buzzer
duration
P56 maximum buzzer duration during an
alarm state
P57 elapsed time between switching on
the compressor and pump down valve
activation (pump down in power up);
also elapsed time between deactivation
of the pump down valve and switching
off the compressor (pump down in
power down)
P58 defrost parameter units of
measurement
0 = P25 h, P24, P26, P28 and P35 min
1 = P25 min, P24, P26, P28 and P35 s
P59 reserved
P60 probe type
0 = NTC
1 = PTC
P61 condenser probe enabling 1 = YES
P62 the temperature above which the
condenser temperature alarm is
activated (with reference to the
condenser probe)
P63 P62 differential
P64 temperature below which the minimum
temperature alarm is activated during
post-chill storage, with relation to P7,
i.e., "P7 + P64" (with reference to the
cabinet probe) 0 = no alarm
P65 temperature above which the maximum
temperature alarm is activated during
post-chill storage, with relation to P7,
i.e. "P7 + P65" (with reference to the
cabinet probe) 0 = no alarm
P66 temperature below which the minimum
temperature alarm is activated during
post-freezing storage, with relation to
P8, i.e. "P8 + P66" (with reference to
the cabinet probe)
0 = no alarm
P67 temperature above which the maximum
temperature alarm is activated during
post-freezing storage, with relation to
P8, i.e. "P8 + P67" (with reference to
the cabinet probe)
0 = no alarm
P68 P64, P65, P66, and P67 differential
P69 storage operation start-up temperature
alarm delay
System Diagnosis Guide
Description Factory
Value
1
20
5
30
3
15
10
0
0
0
70
10
0
0
0
0
2
0
Parameter
P70 temperature alarm delay
P71 enable printing 1 = YES
P72 print interval
P73 HACCP alarm list deletion 1 = YES
P74 Baudrate 0 = 2400
1 = 4800
2 = 9600
3 = 19200
P75 Bit polarity 0 = no polarity 1 = even
2 = odd
P76 Board address
All GBC Trolley Units (Cycle Off Defrost)
Parameter
P0 unit of temperature measurement
0 = °F
1 = °C
P1 cabinet probe offset
P2 evaporator probe offset
P3 needle probe offset
P4 operational setpoint during the second
hard chill step; also, operational
setpoint during normal chilling (with
reference to the cabinet probe)
P5 operational setpoint during freezing
(with reference to the cabinet probe)
P6 operational setpoint during the first
hard chill step (with reference to the
cabinet probe)
P7 operational setpoint during post-chill
storage (with reference to the cabinet
probe)
P8 operational setpoint during post-freeze
storage (with reference to the cabinet
probe)
P9 P4, P5, P6, P7, and P8 differential
P10 set temperature chill end temperature
(with reference to the needle probe)
P11 set temperature freeze end temperature
(with reference to the needle probe)
P12 temperature at which the hard chill
switches from the first step to the
second (with reference to the needle
probe)
P13 temperature above which it is not
possible to start a set temperature
operational cycle (with reference to the
needle probe)
P14 needle probe and the cabinet
temperature for verification of correct
needle probe insertion
0 = the test will not be performed
P15 duration of the second test to check
correct needle probe insertion; see also
P14
P16 maximum set temperature chill
duration; also timed chill duration
P17 maximum set temperature freeze
duration; also timed freeze duration
53
Description Factory
Value
0
0
5
0
2
2
1
Description Factory
Value
1
0
0
0
0
0
-20
3
3
1
3
3
20
99
0
60
90
90