U-Line UCBF632-SS12A User Manual & Service Manual page 50

USER GUIDE
Parameter
P68 P64, P65, P66 and P67 differential
P69 storage operation start-up temperature
alarm delay
P70 temperature alarm delay
P71 enable printing 1 = YES
P72 print interval
P73 HACCP alarm list deletion 1 = YES
P74 Baudrate 0=2400
1=4800
2=9600
3=19200
P75 Bit polarity 0=no polarity 1=even 2=odd
P76 Board address
All GBF units from 5 to 18 Shelves (Hot gas Defrost)
Parameter
P0 unit of temperature measurement
0 = °F
1 = °C
P1 cabinet probe offset
P2 evaporator probe offset
P3 needle probe offset
P4 operational setpoint during the second
hard chill step; also, operational
setpoint during normal chilling (with
reference to the cabinet probe)
P5 operational setpoint during freezing
(with reference to the cabinet probe)
P6 operational setpoint during the first hard
chill step (with reference to the cabinet
probe)
P7 operational setpoint during post-chill
storage (with reference to the cabinet
probe)
P8 operational setpoint during post-freeze
storage (with reference to the cabinet
probe)
P9 P4, P5, P6, P7 and P8 differential
P10 set temperature chill end temperature
(with reference to the needle probe)
P11 set temperature freeze end temperature
(with reference to the needle probe)
P12 temperature at which the hard chill
switches from the first step to the
second (with reference to the needle
probe)
P13 temperature above which it is not
possible to start a set- temperature
operational cycle (with reference to the
needle probe)
P14 needle probe and the cabinet
temperature for verification of correct
needle probe insertion
0 = the test will not be performed
P15 duration of the second test to check
correct needle probe insertion; see also
P14
System Diagnosis Guide
Description Factory
Value
2
0
0
0
5
0
2
2
1
Description Factory
Value
1
2
0
0
0
-40
-20
3
-20
1
3
-18
20
99
0
60
Parameter
P16 maximum set temperature chill
duration; also timed chill duration
P17 maximum set temperature freeze
duration; also timed freeze duration
P18 first hard timed chill step duration
P19 compressor delay from device power on
(from restoration of power)
P20 minimum elapsed time period between
two consecutive compressor start-up
operations
P21 minimum compressor shut-down time
P22 defrost type
0 = electric (defrost on relay)
1 = hot gas (defrost compressor and
relay on)
2 = air (evaporator fan on)
P23 defrost end temperature (with reference
to the evaporator probe)
P24 maximum defrost duration
P25 defrost interval during storage; see also
P26
0 = intermittent defrosting will never
be activated (only the first will be
activated)
P26 first defrost delay from start of storage;
see also P25
P27 defrosting at start of chilling and
freezing 1 = YES
P28 drip-drain duration
P29 resetting of compressor protections at
start of defrosting (only if P22 = 1)
1 = YES
P30 elapsed time between the defrost
request and switching on the
compressor (only if P22 = 1 and
providing that the compressor is off
when the defrost is requested); see P31
(7) (8)also
P31 elapsed time between the defrost
request and activation of the solenoid
valve (only if P22 = 1 and on condition
that the compressor is off when
defrosting is requested); see also P30
P32 temperature above which the evaporator
fan is switched off during storage (with
reference to the evaporator probe)
P33 P32 differential
P34 evaporator fan activity during defrosting
(only if P22 = 0 or 1)
0 = on
1 = off
P35 evaporator stop time after dripping
P36 temperature above which the evaporator
fan is switched off (with reference to the
cabinet probe)
P37 effect caused by activation of microport
input on evaporator fan
0 = no effect
1 = the evaporator fan will be switched
off
50
Description Factory
Value
90
240
45
0
0
0
1
8
10
6
1
0
2
0
30
0
3
1
0
3
90
1