Panasonic PT-SRQ35KC Operating Instructions Manual page 195

[LENS TYPE]
*2
[LENS ID]
*2
[LENS NAME]
*2
[LENS THROW RATIO]
[LENS ZOOM TYPE]
[ZOOM CALIBRATION]
[ON COUNT]
[OPERATING MODE]
[NORMAL]
[ECO]
[QUIET]
[USER1]
[USER2]
[USER3]
[CONSOLIDATED RUNTIME]
[UPGRADE KIT]
[SLOT1]
[SLOT2]
[SIGNAL INFORMATION]
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is
green.
*2 This is displayed only when the standard DC motor unit installed in the Zoom Lens (Model No.: ET-D75LE6, ET-D75LE8, ET-D75LE10C,
ET-D75LE20C, ET-D75LE30C, ET-D75LE40C) is replaced with the stepping motor unit using the Stepping Motor Kit (Model No.:
ET-D75MKS10), or when a projection lens with the stepping motor is attached.
*3 [CONSOLIDATED RUNTIME] can be obtained with the following calculation formula. Values obtained by the calculation formula contain a
slight error.
A x 1.0 + B x 0.8
f A: Runtime of the light source with [OPERATING MODE] set to [NORMAL], [QUIET], [USER1], [USER2], or [USER3]
f B: Runtime of the light source with [OPERATING MODE] set to [ECO]
r [DETAILED INFORMATION]
[INPUT]
[SIGNAL FORMAT]
[SIGNAL FREQUENCY]
[SCAN TYPE]
[TOTAL DOTS]
Chapter 4 Settings — [PROJECTOR SETUP] menu
Displays the type name (type of the projection lens) set to the projection lens.
Displays the ID set to the projection lens.
Displays the name set to the projection lens.
Displays the range of the throw ratio supported by the projection lens.
*2
Displays the drive method of the zoom motor attached to the projection lens.
*2
Displays the zoom calibration result ([OK]/[FAILED]) and the calibration date.
*2
[POWER ON TIMES]
[MECHANICAL SHUTTER]
Displays the setting value of the [PROJECTOR SETUP] menu → [OPERATION SETTING] →
[OPERATING MODE].
Displays the runtime of the light source with [OPERATING MODE] set to [NORMAL].
Displays the runtime of the light source with [OPERATING MODE] set to [ECO].
Displays the runtime of the light source with [OPERATING MODE] set to [QUIET].
Displays the runtime of the light source with [OPERATING MODE] set to [USER1].
Displays the runtime of the light source with [OPERATING MODE] set to [USER2].
Displays the runtime of the light source with [OPERATING MODE] set to [USER3].
Converts the total runtime of the light sources with [OPERATING MODE] set to each item into the
time used with the [NORMAL] setting.
*3
The consolidated runtime is used for a rough indication about when to perform maintenance when the
projector is used in combination of each item in [OPERATING MODE].
[ET-SUK10]
Displays the product model number of the Interface Board installed in <SLOT 1>.
Also, the firmware version is displayed after the product model number.
Displays the product model number of the Interface Board installed in <SLOT 2>.
Also, the firmware version is displayed after the product model number.
[INPUT]
[SIGNAL FORMAT]
[LINK]
[SIMUL]
[4K DIVISION]
[SAMPLING]
[BIT DEPTH]
[SIGNAL LEVEL]
[GAMMA]
[COLOR SPACE]
Conversion formula for [CONSOLIDATED RUNTIME]
Displays the input terminal used for the projected image.
Displays the format of the input signal.
Displays the frequency of the input signal.
Displays the scan type of the input signal.
Displays the total dot count of the input signal.
Displays the number of times the power is turned on.
Displays the number of times the mechanical shutter is closed.
It is counted when [MECHANICAL SHUTTER] is set to [ENABLE].
Displays the activation status by the High Frame Rate Upgrade Kit
(Model No.: ET-SUK10).
Displays the input terminal used for the projected image.
Displays the representative input terminal when one image is
displayed with multiple input signals.
Displays the format of the input signal.
Displays the settings of [SDI LINK], [HDMI LINK], and [DVI-D LINK].
Displays the determination result of the signal when [AUTO] is set.
Displays the [SIMUL INPUT SETTING] setting.
Displays the determination result of the signal when [AUTO(x2-
speed)] is set.
Displays the [4K DIVISION] setting.
Displays the determination result of the signal when [AUTO] is set.
Displays the sampling information and the color format of the input
signal.
Displays the gradation of the input signal.
Displays the signal level of the input signal.
Displays the [GAMMA] setting.
Displays the [COLOR SPACE] setting.
ENGLISH - 195