016: Time Length To First Response At Time Of Fax/Tel Switchover; 017: Pseudo Rbt Signal Pattern On Time Length><018: Pseudo Rbt Signal Pattern Off Time Length (Short)><019: Pseudo Rbt Signal Pattern Off Time Length (Long); 020: Pseudo Ci Signal Pattern On Time Length><021: Pseudo Ci Signal Pattern Off Time Length (Short)><022: Pseudo Ci Signal Pattern Off Time Length (Long); 023: Cng Detention Level For Fax/Tel Switchover - Canon LASER CLASS 810 Service Manual

Set it so that the 1-line transmission time is longer for reception to prevent reception errors caused by a long data length per line (e.g., computer FAX).
16.5.8 <015: hooking detection time>
Allows setting of the hooking detection time.
16.5.9 <016: time length to first response at time of fax/tel switchover>
Allows setting of the time from seizing the line till pseudo RBT is sent, when the Fax/ Tel switching function is operating.
16.5.10 <017: pseudo RBT signal pattern ON time length><018: pseudo RBT signal pattern OFF time length (short)><019:
pseudo RBT signal pattern OFF time length (long)>
Use it to set the pattern of the pseudo RBT signal transmitted at time of a fax/tel switchover.
16.5.11 <020: pseudo CI signal pattern ON time length><021: pseudo CI signal pattern OFF time length (short)><022:
pseudo CI signal pattern OFF time length (long)>
Use it to set the pseudo CI signal pattern transmitted at time of a fax/tel switchover.
16.5.12 <023: CNG detention level for fax/tel switchover>
Use it to set the CNG detention level for a fax/tel switchover.
16.5.13 <024: pseudo RBT transmission level at time of fax/tel switchover>
Use it to set the pseudo transmission level for a fax/tel switchover.
16.5.14 <025: Answering machine connection function signal detection time>
Sets the signal detection time for the answering machine connection function operation. When the answering machine connection function is operating, if the func-
tion does not operate normally because the fax does not detect CNG signal sent from the line, raise this parameter to increase the signal detection time.
16.5.15 <027: V.21 low-speed flag preamble identification length>
Use it to detect the time of detection after which command analysis is started after detecting V.21 low-speed command preambles continuously for a specific period
of time.
16.5.16 <055: Acquisition period of environmental log data>
Use it to change the acquisition period of environmental log data.
16.5.17 <056 - 061: Count type select (if equipped with soft counter functions)>
Use it to confirm the count type indicated on the Counter Check screen, which appears in response to a press on the Counter key.
When '0' is selected, count type will not be indicated.
No.56: Use it to indicate the type of software counter 1 of the control panel. The type of soft counter 1 cannot be changed.
No.57: Use it to change the type of soft counter 2* of the control panel to suit the needs of the user.
No.58: Use it to change the type of soft counter 3* of the control panel to suit the needs of the user.
No.59: Use it to change the type of soft counter 4* of the control panel to suit the needs of the user.
No.60: Use it to change the type of soft counter 5* of the control panel to suit the needs of the user.
No.61: Use it to change the type of soft counter 6* of the control panel to suit the needs of the user.
*:The default type settings of soft counter is different from models.
<Soft Counter Specifications>
The soft counters are classified a follows in terms of input numbers:
100s: total
200s: copy
300s: print
400s: copy + print
500s: scan
700s: received file print
800s: report pint
900s: transmitted scan
Guide to the Table
- 1:Count sheets of all sizes by one.
- 2:Count sheets of the large size by two.
- C:full color
- Bk:black mono
- L:large size (larger than A4/LTR)
- S:small size (A4/LTR or smaller)
MEMO:
Chapter 16
0011-4154
0011-4155
0011-4156
0011-4157
0011-4158
0011-4159
0011-4160
0011-4161
0017-7839
0017-7815
16-19